T24 制动系统 标准查询与下载

BS ISO 26865:2009 道路车辆.制动衬面摩擦材料.带空气制动器的商业车辆用标准性能试验程序

Road vehicles - Brake lining friction materials - Standard performance test procedure for commercial vehicles with air brakes

KS M ISO 4223-1:2009 轮胎工业用一些术语的定义.第1部分:充气轮胎

이 표준은 타이어 산업에서 사용되는 공기 타이어와 관련된 용어 정의와 이에 상응하는 약호,

Definitions of some terms used in the tyre industry-Part 1:Pneumatic tyres

SANS 1622:2009 机动车新备用制动鼓

Specifies the composition and the performance requirements of new replacement cast-iron brake drums for motor vehicles.

New replacement brake drums for motor vehicles

ISO 26865:2009 道路车辆.制动衬面摩擦材料.带气闸的商业车辆用标准性能试验程序

Road vehicles - Brake lining friction materials - Standard performance test procedure for commercial vehicles with air brakes

SAE J44-2009 雪上汽车脚踏闸系统性能要求

This SAE Recommended Practice establishes performance requirements for hand-operated brake systems on recreational noncompetition snowmobiles

Service Brake System Performance Requirements Snowmobiles

SANS 20013:2009 与制动相关的M、N及O 类车辆许可有关的统一规定

Applies to vehicles of categories M2, M3, N and O with regard to braking. Does not cover vehicles with a design speed not exceeding 25 km/h, trailers that may not be coupled with power-driven vehicles with a design speed exceeding 25 km/h, and vehicles

Uniform provisions concerning the approval of vehicles of categories M, N and O with regard to braking

SAE J1469-2009 卡车-牵引车,公共汽车和挂车的空气制动传动装置试验规程

This SAE Recommended Practice provides procedures and methods for testing service, spring applied parking, and combination brake actuators with respect to durability, function, and environmental performance. A minimum of five test units designated A, B, C, D, and E are to be used to perform all tests per 1.1 and 1.2.

Air Brake Actuator Test Procedure, Truck-Tractor, Bus, and Trailers

SAE J2725-2009 道路车辆摩擦材料弹性性能测量

This SAE Standard specifies a method for testing and measuring elastic constants in friction materials by precise ultrasonic velocity measurements.

Road Vehicles Friction Materials Elastic Properties Measurements

KS R ISO 7635:2008 道路车辆.机动车辆用气压或气动.液压制动系统(包括有电子控制功能的机动车辆).试验规程

이 표준은 보충서 1-6을 포함하는 UN-ECE Regulation 13/09를 준수하여

Road vehicles－Air and air/hydraulic braking systems of motor vehicles,including those with electronic control functions－Test procedures

KS R ISO 7401:2008 道路车辆.横向瞬态响应的试验方法.开路试验方法

이 표준은 도로 차량의 과도 응답 거동을 결정하기 위한 개방 루프 시험방법에 대하여 규정하

Road vehicles-Lateral transient response test methods-Open-loop test methods

SAE J1802-2008 制动块有效性等级

This SAE Recommended Practice provides the test procedure and methods to calculate the effectiveness of brake blocks, using an inertia dynamometer. To minimize testing variability, and to potimize standardization and correlation, a single, high volume size of brake block is specified (FMSI No. 4515E) and evaluated in a reference S-cam brake assembly of 419 mm x 178 mm (16.5 in x 7.0 in) size, using a specified brake drum. The purpose of this document is to establish a uniform procedure for the determination and classification of brake effectiveness for commercial vehicle brake blocks. This document will permit comparison of basic frictional properties for brake blocks. Service usage classification ratings and applicable axle load ratings are not included in this document.

Brake Block Effectiveness Rating

NF H96-413:2008 机动工业车辆和牵引车.制动器性能和零件强度

Powered industrial trucks and tractors - Brake performance and component strength.

BS ISO 15484:2008 道路车辆.制动衬面摩擦材料.产品定义和质量保证

Road vehicles - Brake lining friction materials - Product Definition and quality assurance

KS R ISO 8035:2008 超过3.5吨的商业车辆和公共汽车.前牵引附件

이 표준은 최대 총 허용 중량이 3.5톤(ISO-M08) 이상의 상용차 및 버스의 전방에

Commercial road vehicles and buses over 3.5 t－Front towing attachments

KS R ISO 7630:2008 道路车辆.使用石油基液压制动液的鼓式轮闸液压缸弹性O形密封圈(最大工作温度120℃)

이 표준은 광유계 브레이크액을 사용하는 도로 차량의 액압식 드럼 브레이크 휠 실린더의 고무

Road vehicles－Elastomeric O-rings for hydraulic drum brake wheel cylinders using a petroleum base hydraulic brake fluid (service temperature 120 ℃ max.)

SAE J517-2008 液压软管

This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user. The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values. When using SAE J 517 hose for marine applications, see SAE J 1475, SAE J 1942 and SAE J 1942-1. The SAE J517 100R9, 100R10 and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C. The SAEJ 517 100R1A, 100R2A, 100R2B and 100R 2BT are discontinued due to lack of demand. For DOD orders replace 100R1A with 100R1AT, replace 100R2A, 100R2B and 100R2BT with 100R2AT. The SAE J517 100R2AT maximum working pressures will be replaced by the type S maximum working pressures beginning with the year 2009, eliminating the need to label 100R2 as type S. The SAE J517 100R16 maximum working pressures will be replaced by the type S maximum working pressures with the year 2009, eliminating the need to label 100R16 as type S.

Hydraulic Hose

SAE J2318-2008 卡车和客车的气闸制动器试验程序要求

This procedure provides test performance requirements for service, spring applied parking and double diaphragm combination air brake actuators with respect to durability, function and environmental performance when tested in accordance to SAE J 1469. This SAE recommended procedures provides uniform minimum requirements for air brake actuators used in air brake systems for trucks, truck-tractor, bus, and trailers.

Air Brake Actuator Test Performance Requirements Truck and Bus

SAE J1476-2008 额定总重量超过4500公斤(10000镑)的卡车和客车候车制动结构完整性试验规程

This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR. The main purpose of the document is to evaluate the structural integrity of a vehicle's parking brake system. However, other areas, such as suspension and drivetrain system, may also be evaluated during the test, provided that the criteria and procedure detailed as follows are not modified in any way.

Parking Brake Structural Integrity Test Procedure Vehicles over 4500 kg (10,000 lb) GVWR Truck and Bus

KS R ISO 21994:2008 乘用车.防抱死制动系统(ABS)直线制动停车距离.开环试验方法

이 표준은 ABS가 완전하게 작동하는 상태의 직선 제동에서 정지 거리를 결정하기 위한 개회

Passenger cars－Stopping distance at straight-line braking with ABS－Open-loop test method

KS R ISO 611:2008 道路车辆.机动车及其挂车的制动.词汇

이 표준은 KS R ISO 3833에 정의된 전동 차량, 트레일러 또는 이들이 결합된 차량

Road vehicles-Braking of automotive vehicles and their trailers-Vocabulary