T24 制动系统 标准查询与下载
共找到 680 条与 制动系统 相关的标准，共 46 页
이 표준은 KS R ISO 3833에 정의된 전동 차량, 트레일러 또는 이들이 결합된 차량
Road vehicles-Braking of automotive vehicles and their trailers-Vocabulary
- ICS
- 01.040.43;43.040.40
- CCS
- T24
- 发布
- 2008-10-23
- 实施
- 2008-10-23
This SAE Standard specifies minimum performance and test criteria for brake systems to enable uniform assessment of the braking capability of walk-along self-propelled work machines with a mass greater than 115 kg. Service and parking brake systems are covered by this document.
Walk-Along Work Machines Braking Systems Performance Requirements and Test Procedures
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-10-13
- 实施
This SAE standard covers motor vehicle brake fluids of the nonpetroleum type for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. This standard covers different levels of performance properties compared to the SAE J 1703 and SAE J 1705 documents on brake fluids. These fluids are not intended for use under arctic conditions or in braking systems requiring the use of mineral oil based hydraulic fluid These fluids are designed for use in braking systems fitting with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
Borate Ester Based Brake Fluids
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-09-12
- 实施
- 2008-09-13
Road vehicles - Test of braking systems on vehicles with a maximum authorized total mass of over 3,5 t using a roller brake tester - Air over hydraulic and purely hydraulic braking systems
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-08-29
- 实施
- 2008-08-29
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions.These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
Motor Vehicle Brake Fluid
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-08-28
- 实施
- 2008-08-30
本标准规定了客车电涡流缓速器（以下简称“缓速器”）装车性能要求和试验方法。 本标准适用于可载乘员数（不包括驾驶员）多于22人，且最大设计总质量超过5000kg的客车。其他客车可参照执行。
Requirements and test methods of electromagnetic retarder for the ues of bus
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-07-29
- 实施
- 2008-11-01
These performance requirements have been established for manual slack adjusters when tested to SAE J1461.To establish acceptable levels of performance for manual slack adjusters.
Manual Slack Adjuster Performance Requirements
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-07-24
- 实施
이 표준은 UNECE R.E.3에서 정의된 범주 M2, M3, N2, N3, O3 및 O4
Road vehicles-Test of braking systems on vehicles with a maximum authorized total mass of over 3.5 t using a roller brake tester-Part 1:Pneumatic braking systems
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-06-13
- 实施
- 2008-06-13
이 표준은 디스크 브레이크 패드 및 드럼 브레이크 슈 어셈블리의 캐리어와 라이닝 재질 사이
Road vehicles-Brake linings-Shear test procedure for disc brake pad and drum brake shoe assemblies
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-06-13
- 实施
- 2008-06-13
이 표준은 ECE-R 13/09의 부록 1에서 6까지를 따르도록 설계된 범주 M, N 및
Road vehicles－Endurance braking systems ofmotor vehicles and towed vehicles－Test procedures
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-06-13
- 实施
- 2008-06-13
本标准规定了乘用车行车制动器的性能要求及台架试验方法。 本标准适用于GB/T 15089规定的M类车辆用行车制动器总成及摩擦衬片（衬块）总成。
Performance requirements and bench test methods for passenger car brake
- ICS
- CCS
- T24
- 发布
- 2008-06-04
- 实施
- 2008-11-01
This SAE Recommended Practice has been set up by Subcommittee 4 of the Off-Road Machinery Technical Committee and is primarily for directional control valves on construction and industrial machinery equipment as referenced in SAE J1116. The purpose is to establish port area to flow relationship and match valve spool eye ends in relation to rated capacity. Port connections are optional for either the 4-bolt split flange connection or the internal straight thread "O" ring connection.
Hydraulic Directional Control Valves, 3000 psi Maximum
- ICS
- 23.100.50;43.040.40
- CCS
- T24
- 发布
- 2008-05-01
- 实施
This part of ISO 21069 describes a procedure that generates comparable measurement results in roller brake testing, such that the efficiency of the service braking system can be assessed reliably wherever the roller brake tests are performed. The following items are covered in this part of ISO 21069: - symbols and definitions; - test methods; - test conditions; - test equipment required; - accuracy of test equipment; - data recording and calculation needed; - presentation of results; - assessment criteria for pass/fail. The procedure described in this part of ISO 21069 is not applicable to passenger cars.
Road vehicles - Test of braking systems on vehicles with a maximum authorized total mass of over 3,5 t using a roller brake tester - Part 2: Air over hydraulic and purely hydraulic braking systems
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-05
- 实施
ISO 21995:2008 provides a method for the acquisition of suitable braking reference values that the manufacturer is required to provide, and for the use of these reference values in periodical technical inspection (PTI) on air brake systems.
Road vehicles - Test of vehicle air braking systems with a permissible mass of over 3,5 t. Acquisition and use of reference values using a roller brake tester
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-04-30
- 实施
- 2004-03-30
이 규격은 2 MPa(20 bar) 미만의 압력을 가진 압축 공기를 사용하는 도로 차량의
Road vehicles-Pneumatic braking systems-Part 1:Pipes, male fittings and tapped holes with facial sealing surface
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-04-11
- 实施
- 2008-04-11
이 규격은 2 MPa(20 bar) 미만의 압력을 가진 압축 공기를 사용하는 도로 차량의
Road vehicles－Pneumatic braking systems－Part 2：Pipes, male fittings and tapped holes with conical sealing surface
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-04-11
- 实施
- 2008-04-11
This International Standard provides a method for the acquisition of suitable braking reference values that the manufacturer is required to provide, and for the use of these reference values in periodical technical inspection (PTI) on air brake systems.
Road vehicles - Test of vehicle air braking systems with a permissible mass of over 3,5 t - Acquisition and use of reference values using a roller brake tester
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-03-15
- 实施
Applies to vehicles of categories L1, L2, L3, L4 and L5. Does not include categories of (a) vehicles with a Vmax of < 25 km/h, and (b) vehicles equipped for disabled riders.
Uniform provisions concerning the approval of vehicles of categories L1, L2, L3, L4 and L5 with regard to braking
- ICS
- 43.040.40
- CCS
- T24
- 发布
- 2008-02-22
- 实施
This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a. Ability of the parking brake system to lock the braked wheels; b. The vehicle holding or sliding on the grade, fully loaded or unloaded; c. Applied manual effort; d. Unburnished or burnished brake lining friction conditions; e. Down and up grade directions. This document establishes a uniform procedure for determining the parking performance on a grade by the parking brake systems of new vehicles over 4536 kg (10 000 lb) gross vehicle weight rating (GVWR) intended for roadway use.
Truck and Bus Grade Parking Performance Test Procedure
- ICS
- 43.040.40;43.180
- CCS
- T24
- 发布
- 2008-02-01
- 实施
- 2011-06-20
