共找到 322 条与 车辆通用零部件综合 相关的标准,共 22 页
이 규격은 자동차용 기관의 주 베어링 및 크랭크 핀 베어링 중, 반분할 칼라없는 베어링의
Sleeve type half bearings for automobile engines
이 규격의 목적은 차량의 차외 소음 측정에서 시험 노면의 재료, 설계 및 시공을 상세히 규
Acoustics-Specification of test tracks for the purpose of measuring noise emitted by road vehicles
이 규격은 비광유계 브레이크액을 사용하는 자동차용 액압 브레이크 마스터 실린더의 실린더 몸
Automotive parts-Reservoir seals for hydraulic brake master cylinders using a non-petroleum base hydraulic brake fluid
이 규격은 자동차용 디스크 휠을 부착하는 데 사용하는 차륜 너트에 대하여 규정한다.
Wheel nuts for automobiles
이 규격은 자동차용 디스크 휠을 부착하는 데 사용하는 허브 볼트에 대하여 규정한다.
Wheel hub bolts for automobiles
This Material Specification has been supersededm by GMW5M-AL-C. It may be applied only for current projects including g-platform.
Adhesive, Promoter Revision A
この規格は,自動車部品(以下,部品という。)に主として防食・防せい(錆)及び装飾の目的で施される電気めっき()(以下,めっきという。)の通則について規定する。
Automobile parts -- General rules of electroplating
이 규격은 인장에 사용하는 자동차용 컨트롤 케이블에 대하여 규정한다.
Control cables for automobiles
Specifies the test methods used for valve cores and caps for aircraft tyres, with or without inner tubes, and minimum airtightness standards. Constitutes a detailed method allowing products to be evaluated on the same basis, and results to be compared.
Aircraft inner tube and tubeless tyre valves - Cores and caps - Test methods
Evaluation of Effective Hardened Layer Depth in Carburizing, Carbonitriding and Nitriding of Armored Vehicle Parts
本标准规定了装甲车辆零件显微组织检验用试样的选取与制备、显微组织的评定方法及评级图。 本标准适用于评定装甲车辆用钢铁、非铁金属及粉末冶金等零件显微组织的评定。
Evaluation method for microstructure of armored vehicle parts
이 규격은 자동차에서 비광유계 브레이크액을 사용하는 드럼 브레이크용휠 실린더에 대하여 규정
Hydraulic brake wheel cylinders for automotive hydraulic brake systems using a non-petroleum base brake fluid
Unbeschooet etwoiger durch aen Abnehmer eriolgenden Siichprobenprüiungen tragt der Lieferont die Verantwortung dofür,dafi die gelieferte Wore aie Opel - Zeichnungsvors&rifen erfüllt. Mustern sowie Teilen einer ersten Serienlieferung ist uncufQeioraert ein
Adhesive, Pressure Sensitive Revision A
The following information applies to automotive camshaft drives, distributor drives, or other underhood drives that may require synchronization. For other power transmission drives requiring synchronization, refer to Specifications for Drives using synchronous belts (MXL, XL, L, H, XH and XXH belt sections) (IP 24/1978), published jointly by the Rubber Manufacturers Association (RMA), the mechanical power Transmission Association (MPTA), and the Rubber Association of Canada (RAC).
Automotive Synchronous Belt Drives
The purpose of this SAE Recommended Practice is to review factors that influence the behavior of elastomeric components of loading or deforming at a constant rate and to provide guidance concerning test procedures used to define or specify the load/deformation characteristics of elastomeric components. This characteristic is referred to as static stiffness. This is also referred to as a static deflection test.
Recommended Guidelines for Load/Deformation Testing of Elastomeric Components
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号