T32 螺塞、管件 标准查询与下载

WJ 197-1994 装甲车辆标准零件 锥形管节

Armored vehicle standard parts tapered pipe joints

WJ 195-1994 装甲车辆标准零件 三通管接头

Armored Vehicle Standard Parts Tee Pipe Joint

WJ 194-1994 装甲车辆标准零件 弯管接头

Armored Vehicle Standard Parts Elbow Fittings

WJ 212-1994 装甲车辆标准零件 固定卡子

Fixed clips for standard parts of armored vehicles

GM 9985910-1993 No.2,3离合器释放轴承锂复杂润滑脂

This standard is a tool to classify materials. It is essential to see the entirety and not get locked by single requirements.

Grease, Lithium Complex, No. 2 and 3 Clutch Release Bearings

NBN-EN 27326-1993 橡胶管和塑料管．静止条件下抗臭氧能力评估（ISO 7326：1991）

Rubber and plastics hoses. Assessment of ozone resistance under static conditions (ISO 7326:1991)

GM D001-1993 D部分-自攻丝螺钉目录

Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenpriifungen tragt der Lieferant die Verantwortung dofür, dot3 die gelieferte Ware die Opel -2eirhnungsvorschrifen erfüllt. Mustern sowie Teile einer ersten Serienlieferung ist unaufgefordert ei

Section D - Table of Contents Tapping Screws

NBN-EN 28028-1993 用于油漆喷射的橡胶或塑料管．详细说明（ISO 8028：1987）

Rubber and/or plastics hose assemblies for airless paint spraying. Specification (ISO 8028:1987)

NBN-EN 28031-1993 橡胶和塑料导管及挠性管．电阻的测定（ISO 8031：1987）

Rubber and plastics hoses and hose assemblies. Determination of electrical resistance (ISO 8031:1987)

NBN-EN 24671-1993 橡胶和塑料质管子．测量大小的方法（ISO 4671：1984）

Rubber and plastics hose and hose assemblies. Methods of measurement of dimensions (ISO 4671:1984)

NBN-EN 24672-1993 橡胶管和塑料管．温度低于环境温度时柔软性实验（ISO 4672：1988）

Rubber and plastics hoses. Sub-ambiant temperature flexibility tests (ISO 4672:1988)

NBN-EN 26801-1993 橡胶和塑料导管．单位体积膨胀测定（ISO 6801：1983）

Rubber or plastics hoses. Determination of volumetric expansion (ISO 6801:1983)

NBN-EN 26802-1993 被金属丝加固的橡胶和塑料管．水力推动后弯曲度实验（ISO 6802：1991）

Rubber and plastics hose and hose assemblies. Wire reinforced. Hydraulic impulse test with flexing (ISO 6802:1991)

NBN-EN 23994-1993 塑料产品，用于吸液和增压的聚合加强型热塑导管（ISO 3994：1977）

Plastics products. Hose of polymer reinforced thermoplastics for suction and discharge (ISO 3994:1977)

NBN-EN 28030-1993 用于地下采矿的橡胶导管及挠性管．可燃性实验方法（ISO 8030：1987）

Rubber and plastics hoses for underground mining. Methods of test for flammability (ISO 8030:1987)

NBN-EN 28029-1993 塑料管．纺织业中用于加固的易压碎水管．详细说明（ISO 8029：1985）

Plastics hose. General purpose collapsible water hose, textile reinforced. Specification (ISO 8029:1985)

NBN-EN 21746-1993 橡胶管或塑料管．弯曲实验（ISO 1746：1983）

Rubber or plastics hoses and tubing. Bending tests (ISO 1746:1983)

ANSI/SAE J1508-1993 软管夹规格

This SAE Standard covers thirty-two (32) types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems. This document is compiled for the specific purpose of describing the basic characteristics and minimum performance requirements recommended by the manufacturers. No application recommendations are intended or implied. For the benefit of the user in selecting appropriate products for their application, the committee has published ancillary documents that may assist you in this selection. The documents are SAE J1610, SAE J1697, and TMC RP 332.

Hose Clamp Specifications

JIS D 2102:1993 汽车用膨胀塞

この規格は，自動車に使用する打込みプラグ(以下，プラグという。)について規定する。

Expansion plugs for automobiles

GM 9985443-1993 fipg硅橡胶室温硫化胶粘剂

Unbeschadet etwaiger durch den Abnehmer erfolgenden Ctichprobenprüfungen tragt der Lieferant die Verantwortung dafür, dai3 die gelieferte Ware die Opel-Zeichnungtvorschrifien erfüllt. Mustern sowie Teilen einer ersten Serienliefening ist unaufgefordert

Adhesive, RTV, Silicone Rubber, FIPG