共找到 360 条与 螺塞、管件 相关的标准,共 24 页
This specification covers the requirements depending on quality of this upholstery fabric. The general minimum requirements shall be tested on principle to TM 1100 OO.
Adhesive, Two-Part, Urethane, FRP-SMC, Cartridge Use Only
The material is a steel with low yield strength, high tensile strength and good formability. Therefore it is well suited for moulding advanced details.
Adhesive, Two-Part, Urethane, FRP-SMC
The following items are covered: dimensions, material and surface.#,,#
Motor vehicles - Pipe clips for exhaust systems
This SAE Recommended Practice covers design and evaluation of the entire gasoline filler pipe assembly used on cars and light trucks with respect to compliance with CARB (California Air Resources Board) LEV II (meeting or exceeding EPA Tier 2 and EU Stage-5 evaporative emissions requirements). It is limited to an assembly which is joined to the fuel tank using either a hose, Quick Connect Coupling, or a grommet type sealing device. The Design Practice covers the filler cap, filler pipe, filler pipe assembly to tank hose, and filler pipe assembly to tank grommet or spud. It includes recommendations for design of components and assemblies intended to perform successfully in evaporative emission SHED (Sealed Housing for Evaporative Determination) tests, based on best practices known at the time of release.
Fuel Filler Pipe Assembly Design Practice to Meet Low Evaporative Emission Requirements
Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein
Adhesive, Two-Part, Urethane, FRP-SMC
Freigabernuster, für die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstmktion genehmigt sein, ehe eine Lieferung erfolgen kann. Bei beabsichtigter Abweichung von dieser Vorschrift oder von
Grease, Wheel Bearing, High Temperature, No. 2 Revision D
Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein
Medium Build Cathodic Electrocoat Revision D
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of two types of fuel injectors in diesel engines. The location and dimensions of the fuel inlet, leak-off connections, and flange design are not defined since they may vary according to the particular application.
Diesel Fuel Injector Assembly - Flange Mounted Types 5 and 6
UnDaschaao! Error aiger durch oen Abnehmer erislgenden Sti&pror enprüiungen trac: de: Lieferont die Verantwortun asfi oie gelieferie Wore aie =nnunjsvorsnriFren . Mustern SOWO Teiler einer ersten Serieniieferung ist
Anti-Spatter Compounds - MIG Weld Operations Revision B; Do Not Use on New Applications
Stalplat med forhojd strackgrans avsedd for kallformning. Steel sheet of higher yield strength for cold forming.
Oil, Engine High Temperature GF-3
This SAE Standard identifies the material and dimensional requirements for component connector tubes and related items for use in fluid power components. Connector tubes are also identified as quills, ferrules, or transfer tubes. Connector tubes are used to connect fluid passages within a component or to connect one component to another; for example, connecting control valves to subplates. Related items include plugs, undrilled connector tubes and connector tubes for internal check valves and restrictors.
Fluid Systems - Connector Tubes - General Specification and Part Standard
Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprüfungen tragt der Lieferant die Verantwortung dafür, da? die gelieferte Ware die Opei-Zeichnungsvorschriften erfüllt. Ein Prüfbericht mit zahlenma?igen Ergebnissen aus Prüfungen der Lieferu
Vibration Damper - Sprayable, Chip Resistant, High Bake Revision A
この規格は,自動車に使用するねじブラグ(以下,プラグという。)について規定する。
Automotive parts -- Screw plugs
This SAE Standard covers two types of hose fabricated from textile reinforcement and synthetic rubber, assembled with end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of -40 to +150 degrees C (-40 to +302 degrees F) maximum and 10.3 MPa (1500 psi) maximum working pressure. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Class A hose has a nominal OD of 19.84 mm (0.781 in). Class B hose is a lightweight hose with a nominal OD of 17.91 mm (0.705 in). This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering pump to the steering gear.
High-Temperature Power Steering Pressure Hose
Unbeschadet etwaiger durch den Abnehmer erfolgenden Stidrprobenprüfungen tragt der Lieferant die Verantwortung dafür, daß die gelieferte Ware die Opel -Zeichnungsvorsdrriftten erfüllt. Mustern sowie Teilen einer ersten Serieniieferung irt unaufaefordert
Transit Coating Remover Revision A
Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprüfungen tragt der Lieferant die Verontwortvng dafür, da0 die gelieferte Ware die Opal -Zeihnungsvorschriften erfüll?. Mustern sowie Teilen einer ersten Serienlieferung unoufgefordert ein P
Transit Coating (Sprayable) Revision B
Freigabemuster, fur die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein
Primer for Zinc Die Castings Revision F
This SAE Standard covers general and dimensional specifications for brass bodied reusable push-to-connect tube fittings for use in the piping of vehicular air brake systems. This type of fitting is intended for use with nylon tubing per SAE J844. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusable (Push-to-Connect) Fittings Intended for Use in Automotive Air Brake Systems and U.S. Department of Transportation FMVSS 571.
Push-to-Connect Tube Fittings for use in the Piping of Vehicular Air Brake
This SAE Standard specifies the nominal dimensions and tolerances which affect interchangeability between cross-tooth companion flanges type T and mating parts. Dimensions and tolerances of the mating parts, other than those occurring at the interface of the two flanges, are left to the discretion of the manufacturer of that component. This document is equivalent to ISO 8667.
Cross-Tooth Companion Flanges, Type T
Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprufungen tragt der Lieferant die Verantwortung dafur, daß die gelieferte Ware die Opel-Zeichnungsvorschriften erfullt Ein Prufoericht mit zahlenmaßigen Ergebnissen aus Prufungen der Lieferun
Phosphate - Small Parts Revision B
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号