T35 车用电子、电气设备与仪表综合 标准查询与下载

KS R ISO 3470:2007 轿车.挡风玻璃除雾系统.试验方法

이 규격은 승용차(KS R ISO 3833의 3.1.1)에 설치되어 있는 앞 유리창 연무

Passenger cars－Windscreen demisting systems－Test method

KS R ISO 3958:2007 轿车.司机手控活动范围

1.1 이 규격은 남자 및 여자 운전자 인구비에 따라 승용차 내에서 손이 도달하여 조작할

Passenger cars－Driver hand-control reach

KS R ISO 4129:2007 机动脚踏两用车.控制装置、指示器和信号装置的符号

이 규격은 모페드의 각종 제어, 표시 및 경보 장치에 사용되는 기호 및 관습적인 표시를 규

Mopeds-Symbols for controls, indicators and tell-tales

KS R ISO 4164:2007 道路车辆.轻便摩托车.发动机试验规程.净功率

이 규격은 엔진의 회전 속도에 대한 출력과 연료 소비율 곡선을 작성하고 모페드의 성능을 평

Mopeds－Engine test code－Net power

GJB 6106-2007 装甲车辆综合显控终端通用规范

本规范规定了装甲车辆综合显控终端（以下简称为显控终端）的通用要求。 本规范适用于装甲车辆的驾驶员终端、车长终端和炮长终端等，其它类型的显控终端亦可参照使用。

General specincation of integrated display & control terminal for armored vehicles

AQ 3008-2007 危险化学品汽车运输安全监控系统 通信中心与运营控制中心、客户端监控中心间数据接口和数据交换技术规范

本标准规定了危险化学品汽车运输监控系统中，通信控制处理中心与运营控制中心、客户端监控中心间经通信网络进行数据传输和数据交换的通信接口协议的术语、定义和缩略语及接口要求。 本标准适用于危险化学品汽车运输安全监控系统中通信控制处理中心、运营控制中心和客户端监控中心和其他汽车安全运输监控系统的软件设计和开发。

Monitoring system for dangerous chemicals in road transport interface protocol and data exchange standard between Communication Control Processing Center (CCPC) and Operation Control Center (OCC) & client of monitoring center (CMC)

AQ 3007-2007 危险化学品汽车运输安全监控系统 车载终端与通信中心间数据接口协议和数据交换技术规范

本标准规定了危险化学品汽车运输监控系统中，车载终端与通信控制处理中心间经移动通信网络进行无线数据传输和数据交换的通信接口协议。 本标准适用于危险化学品汽车运输安全监控系统的各车载终端和通信中心的开发厂商；其他汽车安全运输监控系统开发商，可参照本技术标准。

Monitoring system for dangerous chemicals in road transport interface protocol and data exchange standard between Telematies Control Unit (TCU)and Communication Control Processing Center (CCPC)

SAE J2748-2006 标准化VHDL-AMS语言统计分析数据包

This document specifies the interface and the behavior of the VHDL-AMS packages for use in modeling statistical behavior. These packages are useful in defining the statistical variation of parameters of electrical, electronic, and mechatronic components and sub-systems. These can then be used with simulation tools to analyze the performance and reliability of systems composed of these components and sub-systems.Providing a standard definition of the package interfaces and their behavior is intended to facilitate the exchange of models between component and system manufacturers and the use of different CAE simulation tools.The SAE statistical package supports the statistical modeling of design parameters subject to tolerances for designs described using the VHDL or VHDL-AMS languages. The performance of a design that uses this package to model parameter tolerances may be analyzed by a Monte Carlo simulation, which consists of multiple simulation runs of the design, each run with a different set of parameter values according to their statistical distributions. The Monte Carlo simulation will yield an estimate of the behavior of the design subject to the parameter tolerances. Additionally, the package may be used to perform an Extreme Value Analysis of a design, that is, an analysis that computes the worst case behavior of the design.The SAE statistical package does not support other statistical modeling needs, for example the modeling of statistical variations of the arrival of events in a queue, or any other situation where a value exhibits a statistical behavior during a single simulation.

VHDL-AMS Statistical Analysis Packages

ISO 4141-3:2006 道路车辆.多芯连接电缆.第3部分:非屏蔽铠装低压电缆的结构、尺寸和标记

This part of ISO 4141 specifies the construction, dimensions and marking of unscreened sheathed low-voltage multi-core cables for the connection of towing and towed vehicles, suitable for the temperature range - 40 °C to + 85 °C.

Road vehicles - Multi-core connecting cables - Part 3: Construction, dimensions and marking of unscreened sheathed low-voltage cables

SAE J2685-2006 正温度系数过电流动作保护装置(PTCs)

This SAE Recommended Practice defines the test conditions, procedures, and performance requirements for PTC (positive temperature coefficient of resistance) overcurrent protection devices. PTCs are typically either polymeric (PPTC) or ceramic (CPTC). It is important to note battery voltages versus powernets/system voltage versus max battery voltages: (12 V/14 V/16 V, 24 V/28 V/32 V, and 36 V/42 V/58 V). All voltages are DC. These devices are typically rated with a maximum operating voltage, which for vehicular systems need to be 16 V (for 12 V batteries), 32 V (for 24 V batteries), and 58 V (for 36 V batteries/42 V powernets). PTC devices are considered to be self-resetting after responding to overcurrent conditions and after such condition has been removed from the affected circuit containing the PTC. The test and evaluation requirements of this document are sufficient to determine relative performance regardless of maximum voltage rating. The suitability of any given PTC device for 42 V electrical systems is dependent upon the manufacturer's design and performance characteristics in higher voltage applications. Whereas electrical arc generation in live circuits poses a hazard to equipment and operators, it is also the recommendation of the Circuit Protection Task Force that vehicular electrical applications employ adequate safety measures to prevent live engage or disengage occurrences of these electrical devices.

Positive Temperature Coefficient Overcurrent Protection Devices (PTCs)

JIS E 6603:2006 乘用车空调设备容量的计算方法

この規格は，日本国内の鉄道用旅客車両に設置される空気調和装置(以下，空調装置という。)に必要な，冷房及び暖房の標準的な容量算出方法について規定する。

Calculation method of air conditioning equipment capacity for passenger cars

SAE J2052-2005 头接触持续时间分析的试验设备

This methodology can be used for all calculations of HIC, with all test devices having an upper neck triaxial load cell mounted rigidly to the head, and head triaxial accelerometers. The purpose of this SAE Information Report is to describe a computer-adaptable technique for determining head engagement and disengagement times for use in the calculation of the HIC without reliance on contact switches or photography.

Test Device Head Contact Duration Analysis

ISO 10599-2:1997/cor 1:2005 轿车收音机.同轴天线连接器.第2部分:特征值、性能要求和试验.技术勘误1

This is Technical Corrigendum 1 to ISO 10599-2-1997 (Car radios — Coaxial aerial connectors — Part 2: Characteristic values, performance requirements and tests)

Car radios - Coaxial aerial connectors - Part 2: Characteristic values, performance requirements and tests; Technical Corrigendum 1

ISO 4141-1:2005 道路车辆.多芯连接电缆.第1部分:基本性能铠装电缆的试验方法和要求

This part of ISO 4141 specifies the test methods and requirements of basic performance multi-core sheathed cables for the connection of towing and towed vehicles, suitable for a temperature range of -40 ℃ to +85 ℃.

Road vehicles - Multi-core connecting cables - Part 1: Test methods and requirements for basic performance sheathed cables

BS ISO 21848:2005 道路车辆.电源电压42 V的电气和电子设备.电负载

ISO 21848:2005 describes the electrical loads that can affect electric and electronic systems and components of road vehicles for a supply voltage of 42 V which may be used in a multiple voltage electrical system. In addition it specifies the tests and resulting requirements, test equipment accuracy being agreed upon between the vehicle manufacturer and the supplier. This International Standard also provides design guidance for the interaction of 42 V with other system voltages.

Road vehicles - Electrical and electronic equipment for a supply voltage of 42 V. Electrical loads

ISO 11992-4:2005 道路车辆.牵引车和拖挂车之间电连接数字信息的交换.第4部分:诊断

This part of ISO 11992 specifies the data communication for diagnostic purposes on a serial data link between a road vehicle and its towed vehicle(s). This part of ISO 11992 is applicable to road vehicles of a maximum authorized total mass greater than 3 500 kg.

Road vehicles - Interchange of digital information on electrical connections between towing and towed vehicles - Part 4: Diagnostics

ISO 11452-4:2005 道路车辆.窄带辐射电磁能量产生的电子干扰用部件试验方法.第4部分:大容量电流注入(BCI)

This part of ISO 11452 specifies bulk current injection (BCI) test methods for determining the immunity of electronic components of passenger cars and commercial vehicles regardless of the propulsion system (e.g. spark-ignition engine, diesel engine, electric motor). The electromagnetic disturbances considered in this part of ISO 11452 are limited to continuous narrowband electromagnetic fields. See ISO 11452-1 for general test conditions.

Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 4: Bulk current injection (BCI)

JIS E 5007:2005 机动车辆用牵引变压器和电感器

この規格は，単相交流式鉄道車両用主変圧器及び電気車の主回路並びに補助回路用のリアクトルについて規定する。ここでリアクトルとは，次のようなものをいう。ーフィルタリアクトルー平滑リアクトルー転流リアクトルー静止形電力変換装置用保護リアクトルー主電動機用誘導分流器ータップ切換器のタップ間渡り用リアクトル ーブレーキ回路用1)アクトルー電波障害抑制用リアクトル

Traction transformers and inductors for rolling stock

JIS B 1404-2:2005 电磁离合器和电磁闸.第2部分:试验方法

この規格は，一直線上にある2軸の一方から他の軸へ，又は同心軸上にある駆動側から被動側へトルクを伝達，遮断又は制動を行う電磁クラッチ及び電磁ブレーキ(以下，クラッチ・ブレーキという。)の試験方法について規定する。

Electromagnetic clutches and electromagnetic brakes -- Part 2: Test methods

JIS B 1404-1:2005 电磁离合器和电磁闸.第1部分:词汇

この規格は，一直線上にある2軸の一方から他の軸へ，又は同心軸上にある駆動側から被動側へトルクを伝達，遮断又は制動を行う電磁クラッチ及ぴ電磁ブレーキ(以下，クラッチ・ブレーキという。)に関する用語について規定する。

Electromagnetic clutches and electromagnetic brakes -- Part 1: Vocabulary