T36 电子、电气设备 标准查询与下载

SAE J2403-2010 中型/重型E/E系统诊断术语

This SAE Recommended Practice is applicable to all E/E systems on MD and HD vehicles. The terms defined are largely focused on compression-ignited and spark-ignited engines. Specific applications of this document include diagnostic, service and repair manuals, bulletins and updates, training manuals, repair data bases, under-hood emission labels, and emission certification applications. This document focuses on diagnostic terms, definitions, abbreviations, and acronyms applicable to E/E systems. It also covers mechanical systems which require definition. Nothing in this document should be construed as prohibiting the introduction of a term, abbreviation, or acronym not covered by this document. The use and appropriate updating of this document is strongly encouraged. Certain terms have already been in common use and are readily understood by manufacturers and technicians, but do not follow the methodology of this document. To preserve this understanding, these terms were included and have been identified with "historically acceptable common usage," so they will not erroneously serve as a precedent in the construction of new names. These terms fall into three categories: a. Acronyms that do not logically fit the term. b. Acronyms existing at the component level, i.e., their terms contain the base word or noun that describes the generic item that is being further defined. c. Acronyms for terms that appear to contain the base word, but are frequently used as a modifier to another base word. (This use may possibly be thought of as following the methodology since the acronym is normally used as a modifier.)

Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

SAE J1939/31-2010 网路层

The Network Layer document describes the requirements and services for Network Interconnection ECUs (NIECU) thatenable electronic control units (ECUs) on a network segment to intercommunicate with other ECUs on different networksegments of the vehicle network. This document defines various types of NIECUs. The information in this documentapplies only to ECUs that are intended to provide networking services. It is not necessary for an ECU to provide any ofthese services in order to be compliant with the SAE J1939 protocol.

Network Layer

DB31/T 466-2009 公共汽(电)车车载视频监控系统基本技术要求

The Technical Requirements of Video Monitoring System for Urban Public Transportation Vehicles

BS ISO 16750-5:2010 道路车辆.电气和电子设备用环境条件和试验.化学载荷

Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Chemical loads

SANS 10250:2010 汽车空调系统配件和维修中心

Specifies the site conditions and operating methods that should be uniformly applied in all franchised and independent fitment and repair centres to ensure that a high level of customer satisfaction is maintained. Also addresses protection of the environ

Fitment and repair centres for automotive air-conditioning systems

UL SUBJECT 458A-2010 电力陆上车辆电源转换器/逆变器调查大纲

1.1 These requirements cover fixed and stationary power converters, and accessories having a nominal rating of 600 V or less, direct and alternating current. These converters are intended for use within electric vehicle land vehicles where not directly exposed to outdoor conditions, and are intended to be employed in accordance with the National Electrical Code, NFPA 70. 1.2 These requirements also cover fixed, stationary and portable power inverters having a dc input and a 120 or 240 V ac output. These inverters are intended for use within electric vehicle land vehicles where not directly exposed to outdoor conditions, and are intended to be employed in accordance with the National Electrical Code, NFPA 70. 1.3 These requirements also cover converters/inverters that are additionally intended to charge batteries. 1.4 This outline does not cover fixed and stationary power converters, power-converter systems, and accessories intended for use within land vehicles which are not electric vehicles. Fixed and stationary power converters, power-converter systems, and power inverters and power-inverter systems accessories intended for use within land vehicles other than electric vehicle land vehicles are covered under the Standard for Power Converters/Inverters and Power Converter/Inverter Systems for Land Vehicles and Marine Crafts, UL 458.

OUTLINE OF INVESTIGATION FOR POWER CONVERTERS/INVERTERS FOR ELECTRIC LAND VEHICLES

BS ISO 16750-4:2010 道路车辆.电气和电子设备用环境条件和试验.气候载荷

Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Climatic loads

ISO 22840:2010 智能运输系统.援助倒车操纵的设备.支持援助系统扩展范围(ERBA)

Intelligent transport systems - Devices to aid reverse manoeuvres - Extended-range backing aid systems (ERBA)

SAE J1742-2010 道路车辆高压电气线束试验方法和一般性能要求用连接件

Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in high power road vehicle applications That operates at either 20 V to 600 volts regardless of the current applied or any current greater than or equal to 80 A regardless of the voltage applied. These procedures are applicable only to terminals used for In-Line, Header, and Device Connectors and for cable sizes up to 120 mm/u2 (4/0). In cases where power levels are mixed in the same connector, (i.e. sensing or normal 14.5 volt system circuits with High Power Contacts) the High Power Contacts must pass J1742 requirements, and all other contacts must pass SAE J2223-2 requirements. The connection system (housing and high power contacts) shall meet J1742 requirements. The requirements and procedures in this document are not intended for connections internal to electrical/electronic modules or complete subassemblies. This document does not contain a test for EMI/EMC since these parameters must be tested as a combination of cable and connector. These are considered system level requirements. Determination of the need and type of test must be considered at that level.

Connections for High Voltage On-Board Road Vehicle Electrical Wiring Harnesses Test Methods and General Performance Requirements

ISO 17386:2010 交通信息和控制系统.低速操作的操控辅助装置(MALSO).性能要求和试验程序

This International Standard addresses light-duty vehicles, e.g. passenger cars, pick-up trucks, light vans and sport utility vehicles (motorcycles excluded) equipped with MALSO systems. It specifies minimum functionality requirements which the driver can generally expect of the device, i.e. detection of and information on the presence of relevant obstacles within a defined (short) detection range. It defines minimum requirements for failure indication as well as performance test procedures; it includes rules for the general information strategy but does not restrict the kind of information or display system. MALSO systems use object-detection devices (sensors) for ranging in order to provide the driver with information based on the distance to obstacles. The sensing technology is not addressed; however, technology affects the performance-test procedures set up in this International Standard (see Clause 7). The current test objects are defined based on systems using ultrasonic sensors, which reflect the most commonly used technology at the time of publishing this International Standard. For other sensing technologies possibly coming up in the future, these test objects shall be checked and changed if required. Visibility-enhancement systems like video-camera aids without distance ranging and warning are not covered by this International Standard.

Transport information and control systems - Manoeuvring Aids for Low Speed Operation (MALSO) - Performance requirements and test procedures

SAE J1772-2010 汽车工程师协会(SAE)电动车电导充电耦合器

This SAE Recommended Practice covers the general physical, electrical, functional and performance requirements to facilitate conductive charging of EV/PHEV vehicles in North America. This document defines a common EV/PHEV and supply equipment vehicle conductive charging method operational requirements and the funcational and dimensional requirements for the vehicle inlet and mating connector.

SAE Electric Vehicle Conductive Charge Coupler

SAE J551/17-2010 机动车电磁免疫性的电力线电磁场

This SAE Standard specifies the test methods and procedures for testing passenger cars and commercial vehicles to magnetic fields generated by power transmission lines and generating stations. SAE J 551-1 specifies general, definitions, practical use, and basic principles of the test procedure.

Vehicle Electromagnetic Immunity Power Line Magnetic Fields

SAE J2191-2010 标准化卡车和拖拉机电路的鉴定用推荐实施规程

This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer's primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5. This document will provide a common method of identifying circuit function for commercially available Class 8 vehicles. It will guide the service technician in diagnosing vehicle electrical subsystems. The identification method will supplement component OEM circuit identification for each major subsystem.

Recommended Practice for Identification of Standardized Truck and Tractor Electrical Circuits

JJG 771-2010 机动车雷达测速仪检定装置

本规程适用于机动车雷达测速仪检定装置（以下简称检定装置）的首次检定、后续检定和使用检验。

Verification Regulation of Test Equipment for Vehicle Speed Radar Measurement Meters

SAE USCAR38-2010 超声波包铜钢丝/电缆终端用性能规范

Performance specification for ultrasonically welded wire/cable termination

SAE USCAR15-2010 测试汽车电灯泡插座用规范

This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connector, direct wire wedge base sockets, circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendix E whenever the following occurs: New design; Design, material or process change made to an existing device, which could affect the outcome of the test. The test sequence shown in Appendix F shall be run annually.

Specification for testing automotive light bulb sockets

IEEE 1609.11-2010 车载环境的无线访问(WAVE)标准.智能运输系统(ITS)用空中电子支付数据交换协议

Wireless Access in Vehicular Environments (WAVE)— Over-the-Air Electronic Payment Data Exchange Protocol for Intelligent Transportation Systems (ITS)

BS ISO 10924-4:2009 道路车辆.断路器.CB15式带有标签的中等断路器(刀片式)

Road vehicles - Circuit breakers - Medium circuit breakers with tabs (Blade type), Form CB15

BS ISO 10924-1:2009 道路车辆.断路器.术语及一般试验要求

Road vehicles - Circuit breakers - Definitions and general test requirements

SAE J1474-2009 重型非金属发动机冷却扇.材料、制造和试验的注意事项

The following topics are included in this report: Section 2. References, Section 3- Definitions, Section 4- Material Selection, Section 5- Production Considerations, Section 6- Initial Structural Integrity, Section 7- In-Vehicle Testing, Section 8- Laboratory Testing The Material Selection section lists environmental factors and material properties which should be considered when determining appropriate fan material(s) for a given application. The Production Considerations section covers various aspects of machine selection, mold design, and process control. The Initial Structural Integrity section lists factors which should be considered in addition to those covered by the same section of SAE J1390. The In-Vehicle Testing section lists factors which should be considered in addition to those covered by the same section of SAE J1390. The Laboratory Testing section addresses some test considerations and methods for nonmetallic fans which differ from those used with metallic fans or which were not included in the Durability Test Methods section of SAE J1390. This report exists to identify general methodology which addresses the areas of evaluation listed previously for injection-molded nylon fans. It is envisioned that those working with other processes and/or materials can use SAE J1390 and this document as starting points in the development of structural analysis methodology pertinent to their particular combination(s).

Heavy-Duty Nonmetallic Engine Cooling Fans Material, Manufacturing and Test Considerations