T36 电子、电气设备 标准查询与下载

SANS 2362:1997 陆地车辆移动无线电设备的安装

Provides guidance for the installation in vehicles of land mobile radio, mobile telephones, "in-car" mounting kits for transportable and handheld equipment and ancillary equipment associated with the above. Details the recommended methods for the safe an

Installation of mobile radio equipment in land based vehicles

SAE J180-2002 非公路工作机用电子收费系统

This standard covers alternator design and mounting configurations for electrical charging systems for construction and industrial machinery. To provide information on which to base machine and component design which will result in the most satisfactory operation of charging systems in the severe environment of construction and industrial machinery.

Electrical Charging Systems for Off Highway Work Machines

SAE HS-1738-2002 SAE 工业机械电气标准 - NFPA 79 的补充 不包括图像；请参考全球

This edition of HS-1738 provides requirements and recommendations relating to the electrical equipment of machines so as to promote safety of persons and property, consistency of control response, and ease of maintenance. Although it is desired that high performance be achieved, the above mentioned essential factors should not be compromised.

SAE Electrical Standard for Industrial Machinery - Supplement to NFPA 79 IMAGES ARE NOT INCLUDED; PLEASE REFER TO GLOBAL

ASTM C1534-02 作为喇叭的吸热吸声衬垫使用的软质聚合物塑料泡沫薄片的标准规范

1.1 This specification covers the composition, dimensions, and physical properties of flexible unfaced foam sheet, used to insulate interior surfaces of HVAC ducts, plenums and equipment used for the distribution of conditioned air with a temperature of up to 250176;F (121176;C).1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are in SI, and are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems

SAE J1494-2001 电池跨接线

The purpose of this SAE Recommended Practice is to establish minimum performance and user information requirements for battery booster cable sets. Such sets may be used to provide a temporary connection of a surface vehicle battery to another similar battery to provide emergency power when required. This recommended practice DOES NOT ENDORSE NOR RECOMMEND the potentially hazardous procedure of jump starting a vehicle.

Battery Booster Cables

SAE J2590-2001 汽车电子网络PMODE

This Recommended Practice describes the power mode requirements for in-vehicle networks that conform to the Automotive Multimedia Interface Collaboration (AMI-C).

PMODE for In-Vehicle Networks

ISO 15170-2:2001 道路车辆 带有插销和螺旋锁的4柱电连接器 第2部分：试验和要求

This part of ISO 15170 specifies tests and requirements for electrical connectors and connections with up to four poles and twist lock coupling. This type of connection is intended for electrical connections in truck, bus and trailer applications (e.g. for components directly mounted on the engine).

Road vehicles - Four-pole electrical connectors with pins and twist lock - Part 2: Tests and requirements

ISO 4165:2001 道路车辆 电气连接 双极接线盒

This International Standard specifies the dimensions and electrical characteristics of the double-pole connection required for the interchangeability of the electrical connections used to supply additional appliances in road vehicles with a nominal supply voltage of 12 V or 24 V d.c.

Road vehicles - Electrical connections - Double-pole connection

ISO 14572:2001 道路车辆 圆形、非屏蔽60V和600V多芯铠装电缆 基本性能和高性能电缆的试验方法和要求

This International Standard specifies test methods and requirements for basic and high performance round, unscreened 60 V and 600 V multicore sheathed cables intended for use in road vehicle applications. For the unscreened single-core cables used in the multicore cable, see ISO 6722. Other cores may be used, but with the construction and tests required to ensure functionality of these cores agreed between the customer and supplier. For temperature classes, see ISO 6722.

Road vehicles - Round, unscreened 60 V and 600 V multicore sheathed cables - Test methods and requirements for basic and high performance cables

SAE J2366/1L-2001 智能交通系统数据公交.低阻抗立体声音频(LISA)

This SAE Recommended Practice describes the Low Impedance Stereo Audio (LISA) bus, which may be used in conjunction with the physical layer of the IDB-C.

ITS Data Bus - Low Impedance Stereo Audio (LISA)

ISO 15170-1:2001 道路车辆 带有插销和螺旋锁的4柱电连接器 第1部分：尺寸和应用等级

This part of ISO 15170 specifies those items, principally dimensions and classes of application of electrical connectors with up to four pins and twist lock coupling, necessary for assuring the interchangeability of both parts of electrical connections according to ISO 15170. This type of connection is intended for electrical connections in truck, bus and trailer applications (e.g. for components directly mounted on the engine).

Road vehicles - Four-pole electrical connectors with pins and twist lock - Part 1: Dimensions and classes of applications

NF R13-462:2001 道路车辆.车载防水连接器用连接界面.0.64 mm 和/或 1.5 mm 四列式连接器

Road vehicles - Connection interface for on-board waterproof connectors - Connectors with four rows of 0,64 mm and/or 1,5 mm.

ISO 15031-1:2001 道路车辆 车辆与发射相关诊断的外部设备之间的通信 第1部分：一般信息

This part of ISO 15031 provides an introduction to ISO 15031 and its application to communication between vehicles and external equipment for emissions-related diagnostics. This part of ISO 15031 presents an overview of ISO 15031, describing its partitioning and the relation of its other parts to SAE (US Society of Automotive Engineers) recommended practices.

Road vehicles - Communication between vehicle and external equipment for emmissions-related diagnostics - Part 1: General information

ISO 16844-1:2001 道路车辆 速度记录器系统 第1部分：电连接器

This part of ISO 16844 gives the dimensions and tests and requirements for the performance of electrical connectors needed for ensuring the interchangeability of different components of the tachograph systems used for road vehicles in accordance with Council Regulation (EEC) No. 3821/85 on recording equipment in road transport. In particular, this part of ISO 16844 specifies the connector used to connect the recording unit of the tachograph to the vehicle electrical wiring harness.

Road vehicles - Tachograph systems - Part 1: Electrical connectors

QC/T 417.5-2001 车用电线束插接器 第5部分 用于单线和多线插接器的圆柱式插接件的尺寸和特殊要求

本标准规定了圆柱式插接件的尺寸和特殊要求。本标准适用于车用电线束中用于单线和多线插接器及车辆上用于维修的分离插接器。

Automotive wiring harness connectors - Part 5 - Dimensions and special requirements for cylindrical connectors for single-wire and multi-wire connectors

QC/T 417.4-2001 车用电线束插接器 第4部分 多线片式插接件的尺寸和特殊要求

本标准规定了多线片式插接件的尺寸和特殊要求。本标准适用于车用电线束中的多线插接器及车辆上用于维修的分离插接器。

Automotive wiring harness connectors - Part 4 Dimensions and special requirements for multi-wire blade connectors

QC/T 417.3-2001 车用电线束插接器 第3部分 单线片式插接件的尺寸和特殊要求

本标准规定了单线片式插接件的尺寸和特殊要求。本标准适用于车用电线束中的单线片式插接器，例如附录A给定的插座。本标准还适用于车辆上用于维修的分离插接器。

Automotive wiring harness connectors - Part 3 Dimensions and special requirements for single-wire blade connectors

QC/T 417.2-2001 车用电线束插接器 第2部分 试验方法和一般性能要求（摩托车部分）

本标准规定了摩托车和轻便摩托车电气线路用低压电缆(电线)单线和多线插接器的定义、试验方法和性能要求。 　　本标准适用于片式和柱式插接器，其它型式的插接器亦可参照使用。

Automotive wiring harness connectors Part 2 Test methods and general performance requirements (motorcycle part)

QC/T 417.1-2001 车用电线束插接器 第1部分 定义，试验方法和一般性能要求（汽车部分）

本标准规定了车用电线束插接器的定义，一般性能要求以及具体试验方法。本标准适用于车用电线束中的单线和多线插接器及车辆上用于维修的俄分离插接器。本标准不适用于直接与印制电路板连接的插接器和电子仪器的内部连接。

Automotive wiring harness connectors Part 1 Definitions, test methods and general performance requirements (automotive part)

ISO 11748-2:2001 道路车辆 电气和电子系统的技术文件编制 第2部分：文件编制协议

This part of ISO 11748 gives guidelines for the structure and content of the documentation agreement established between partners in the development of on-board electronic control systems used in road vehicles. The documentation agreement describes the exchange of documents between the partners and is specific to a given development. This part of ISO 11748 provides a framework for any such agreement.

Road vehicles - Technical documentation of electrical and electronic systems - Part 2: Documentation agreement