V00 标准化、质量管理 标准查询与下载

HB 7576-1997 航空粉末冶金制品质量控制标准

Quality Control Standards for Aeronautical Powder Metallurgy Products

SAE AS7114-1997 国家航空航天和国防承包商认证计划无损测试要求,代替AS 7100/1A

This Aerospace Standard (AS) establishes the requirements for suppliers of nondestructive testing (NDT) to be accredited by the National Aerospace and Defense Contractors Accrdditation Program (NADCAP) in accordance with the current revision of SAE AS7003. Using the audit checklist and the applicable supplementary checklists will ensure that accredited NDT suppliers meet the requirements of this standard and all applicable supplementary standards. When customer requirements differ from those specified herein, the customer requirements shall take precedence.

National Aerospace and Defense Contractors Accreditation Program Requirements for Nondestructive Testing Superseding AS 7100/1A

SAE AS7114/4-1997 Nadcap无损测试设施射线照相术调查要求,代替AS 7100/1A [代替: SAE AS 7110/1D,SAE AS 7110/1C,SAE AS 7110/1B,SAE AS 7110/1A]

This Aerospace Standard (AS) is to be used to supplement AS7114. In addition to the requirements contained in AS7114, the requirements contained herein shall apply to suppliers seeking NADCAP accreditation for Radiography. When customer requirements differ from those specified herein, the customer requirements shall take precedence.

NADCAP Requirements for Nondestructive Testing Facility Radiography Superseding AS 7100/1A [Superseded: SAE AS 7110/1D, SAE AS 7110/1C, SAE AS 7110/1B, SAE AS 7110/1A]

SAE AS7114/3-1997 Nadcap无损测试设施超声波调查要求,代替AS 7100/1A

This Aerospace Standard (AS) is to be used as a supplement to AS7114. In addition to the requirements contained in AS7114, the requirements contained herein shall apply to suppliers seeking NADCAP accreditation for Ultrasonic Nondestructive Testing. When customer requirements differ from those specified herein, the customer requirements shall take precedence.

Nadcap Requirements for Nondestructive Testing Facility Ultrasonic Survey Superseding AS 7100/1A

SAE AS7114/2-1997 针对无损检测磁粉调查的国家航空航天和国防承包商认证计划要求,代替AS 7100/1A

This Aerospace Standard is to be used as a supplement to SAE AS7114. In addition to the requirements contained in AS7114, the requirements contained herein shall apply to suppliers seeking NADCAP accreditation for Magnetic Particle Inspection. When customer requirements differ from those specified herein, the customer requirements shall take precedence.

Nadcap Requirements for Nondestructive Testing Magnetic Particle Survey Superseding AS 7100/1A

SAE AS7114/1-1997 Nadcap无损测试设施渗透剂调查要求,代替AS 7100/1A

This Aerospace Standard (AS) is to be used to supplement AS7114. In addition to the requirements contained in AS7114, the requirements contained herein shall apply to suppliers seeking NADCAP accreditation for Penetrant Nondesctructive Testing. When customer requirements differ from those specified herein, the customer requirements shall take precedence.

Nadcap Requirements for Nondestructive Testing Facility Penetrant Survey Superseding AS 7100/1A

SAE AS7108/2-1997 针对蚀刻制程(宏观结构,硝酸乙醇溶液,韧度,蓝蚀刻阳极)的国家航空航天和国防承包商认证计划要求

This Aerospace Standard (AS) establishes the requirements for suppliers for Etching Processes to be accredited by the National Aerospace and Defense Contractors Accreditation Program (NADCAP). These requirements may be supplemented by additional requirements specified by NADCAP Chemical Processing suppliers meet all of the requirements in this standard and all applicable supplementary standards.

National Aerospace and Defense Contractors Accreditation Program Requirements for Etch Processes (Macrostructure, Nital, Temper, Blue Etch Anodize)

MH/T 0002-1997 标准编写的基本规定

本标准规定了标准编写的要求和表述方法。 本标准适用于编写民用航空各级标准。

General rules for drafting standards

MH/T 0003-1997 标准编号规定

本标准规定了民用航空标准的编号和标记方法。 本标准适用于民航行业标准的编号和标记。

Rules for numbering standards

MH/T 0001-1997 标准的制定、修订程序和要求

本标准规定了民用航空标准制定、修订及复审的程序和要求。 本标准适用于制定、修订及复审民航行业标准。由民航起草的国家标准可参照使用。

Requirements and procedures for standards drawing up and reviewing

AC-145-10-1997 关于民用航空期保留项目管理指南

About the management guideline of civil aviation reservation project

ARINC 737-1 ITEM 2.0-1997 可交换性标准

Interchangeability Standards

Interchangeability Standards

NAVY MIL-PRF-24712 A (1)-1997 粉末覆盖物(衡量标准)

This amendment forms a part of MIL-PRF-24712A, dated 25 May 1995, and is approved for use by all Departments and Agencies of the Department of Defense.

COATINGS, POWDER (METRIC)

CAA CAP 667-1997 1985-1994年通用航空器重大事故的回顾

3.1 The Group decided that a review of all GA accidents (over 250 per year) and incidents was impracticable. There was a risk that some significant issues could be outweighed by relatively minor accidents such as landing gear collapses. It was agreed that the review would concentrate on fatal accidents to UK registered aeroplanes and helicopters of 5700kg maximum take-off mass and below which occurred in the UK and abroad during the 10 year period 1 January 1985 to 31 December 1994. Microlights, gyroplanes and gliders were excluded as they have different airworthiness codes and pilot licensing standards. This provided a manageable number of accidents (166) for analysis while it corresponded with the CAP 542 work (aeroplanes). 3.2 Fatal accidents where there was only third party involvement (e.g. people moving into rotating propellers or rotors) were included since these could have been affected by the operational environment. 3.3 The CAA's Mandatory Occurrence Reporting Scheme records all significant hazardous or potentially hazardous occurrences as well as accidents. For the purposes of this review, the occurrence computer database did not contain sufficient background material on the fatal accidents so Air Accidents Investigation Branch (MB) Bulletins, occurrence files and licensing records as well as other sources were used. 3.4 A number of accidents, 20 (12%), involved UK registered aircraft flying outside the UK and, thus, were investigated by foreign authorities. Very few had produced adequate reports and in spite of enquiries via Air Accidents Investigation Branch, very little has been forthcoming and, in most cases, it was not possible to allocate any causal factors. The 1987 accident review group also experienced this difficulty.

Review of General Aviation Fatal Accident 1985-1994 Reprinted May 2002

ARINC 747-2 SUPP-1997 附录

Supplements

Supplements

ARINC 651-1 ITEM 11.0-1997 标准IMA模块

Standard IMA Modules

Standard IMA Modules

SAE AS7112-1997 国家航空航天和国防承包商认证程序;流体系统组件要求

This Aerospace Standard (AS) establishes the requirements for manufacturers of Fluid System Components to be accredited by the National Aerospace and Defense Contractors Accreditation Program (NADCAP). NADCAP accreditation is granted in accordance with SAE AS7003 after demonstrating compliance with the requirements herein. These requirements may be supplemented by additional requirements specified by NADCAP Fluid System Components Task Group. Using the corrsponding Audit Criteria checklist (PRI ACs) will ensure that accredited Fluid System suppliers meet all of the requirements in this standard and all applicable supplementary standards. The purpose of this audit program is to assess a suppliers ability to consistently provide a product or service that conforms to the technical specifications and customer requirements. The corresponding audit critiera are also structured to obtain information relevant to management practices and processes that directly or indirectly affect the product or service. The information thus obtained will be used for determination of accreditation status, and may be used by the supplier to guide improvements in the product/service or associated processes

National Aerospace aand Defense Contractors Accreeditation Program; Requirements for Fluid System Components

ARINC 651-1 APP-1997 附录

Appendix

Appendix

ARINC 651-1 ITEM 2.0-1997 目标

Objectives

Objectives

QJ 2874-1997 质量与可靠性信息库命名方法与代码

Naming Method and Code of Quality and Reliability Information Base