V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3650D-2012 未增塑的聚氯三氟乙烯杆材、薄板和模制型材

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of rods, sheets, and molded shapes. Primarily for parts requiring chemical inertness and high impact strength up to 200 degrees C (392 degrees F) or high-frequency electrical insulating properties up to 165 degrees C (329 degrees F).

Rods, Sheets, and Molded Shapes, Polychlorotrifluoroethylene (PCTFE), Unplasticized

SAE AMS3751C-2012 空心玻璃微球形体

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers hollow glass microspheres. Primarily as a filler material in syntactic foam shapes or parts for dielectric applications.

Microspheres, Hollow Glass

SAE AMS3664C-2012 乙烯涂层的玻璃织物

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers four types of glass cloth coated on both sides with a flexible, vinyl-copolymer resin, the type of glass cloth varying with nominal thickness of the product. Primarily for use as a nonporous, abrasion and flame resistant, trim cloth or as a covering for thermal and acoustic insulation blankets for use up to 80 degrees C (180 degrees F).

Cloth, Glass, Vinyl Coated

SAE AMS3645D-2012 未增塑的聚氯三氟乙烯压缩模塑大型材

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers polychlorotrifluoroethylene (PCTFE) in the form of sheet over 0.250 in. (6.25 mm) in thickness, rod, heavy wall tubing, and large molded and machined parts. Primarily for parts requiring chemical inertness and toughness up to 200C degrees (390F degrees) or high-frequency electrical insulating properties up to 165C degrees (330F degrees). The material also may be used at cryogenic temperatures.

Polychlorotrifluoroethylene, Compression Molded-Heavy Sections, Unplasticized

SAE AMS3722B-2012 蜂窝状纸、125 1b(55 kg)纸

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers paper base honey comb material having a cell size of 0.440 in. (11.18 mm). Unless otherwise ordered, size 0.440 in. (11.18 mm) will be supplied. Primarily for use as a core in sandwich construction of light weight partitions, space fillers, and non-structural parts. This product is not intended for aircraft structural or exterior applications.

Paper Honeycomb, 125 lb (55 kg) Paper

SAE AMS3638G-2012 热收缩比为2:1的热收缩半刚性电气绝缘着色散热聚烯烃塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an irradiated, thermally-stabilized, flame-retardant, modified polyolefin plastic in the form of thin-wall tubing. This tubing has been used typically as a semi-rigid, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to a temperature higher than 120 degrees C (248 degrees F), but usage is not limited to such applications.

Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Pigmented, Semi-Rigid, Heat-Shrinkable, 2 to 1 Shrink Ratio

SAE AMS3635E-2012 闭孔的改良乙烯泡沫塑料板材和带材

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a closed-cell, modified vinyl plastic foam in the form of sheet and strip up to 1-1/2 inches (38.1 mm) in nominal thickness. These products have been used typically for parts, such as head rest pads and arm rests, requiring an impact-resistant, slow-recovery, energy-absorbing product, but usage is not limited to such applications.

Plastic Sheet and Strip, Modified Vinyl, Foamed, Closed Cell

SAE AMS3666E-2012 玻璃织物增强的聚四氟乙烯薄板

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers glass-cloth-reinforced polytetrafluoroethylene (PTFE) resin in the form of sheet. This sheet has been used typically for electrical, electronic, and mechanical applications requiring a composite having the high strength and nondeforming characteristics of woven glass cloth and the electrical, chemical, and heat resistance and the anti-stick and low- friction properties of PTFE resin, but usage is not limited to such applications.

Polytetrafluoroethylene (PTFE) Sheet, Glass Cloth Reinforced

SAE AMS3636H-2012 缩减比为2:1的、热缩、柔性、加色、辐照的聚烯烃电绝缘塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an irradiated, thermally-stabilized, flame-resistant, modified polyolefin plastic in the form of flexible, thin-wall, heat-shrinkable tubing. Primarily for use as a flexible, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 120 degrees C (248 degrees F) or higher.

Tubing, Plastic, Electrical Insulation, Irradiated Polyolefin, Pigmented, Flexible, Heat-Shrinkable, 2 to 1 Shrink Ratio

SAE AMS3649D-2012 未增塑的聚氯三氟乙烯薄膜

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of film and film tape 0.010 in. (0.25 mm) and under in nominal thickness. Primarily for parts requiring chemical inertness up to 200 degrees C (392 degrees F) and electrical insulating properties up to 165 degrees C (329 degrees F).

Film, Polychlorotrifluoroethylene (PCTFE) Unplasticized

SAE AMS3639G-2012 电绝缘、洁净、半刚性、2:1收缩率热可收缩的经辐照聚烯烃塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of semi-rigid, thin-wall, heat-shinkable tubing. This tubing has been used typically as a semi-rigid, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 120 degrees C (250 degrees F) or higher, but usage is not limited to such applications.

Tubing, Irradiated Polyolefin Plastic, Electrical Insulation, Clear, Semi-Rigid, Heat-Shrinkable, 2 to 1 Shrink Ratio

SAE AMS3637G-2012 热收缩比为2:1的热收缩柔性电气绝缘透明散热聚烯烃塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of thin-wall tubing. This tubing has been used typically as a flexible, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 120 degrees C (248 degrees F) or higher, but usage is not limited to such applications.

Tubing, Irradiated Polyolefin Plastic, Electrical Insulation, Clear, Flexible, Heat Shrinkable, 2 to 1 Shrink Ratio

SAE AMS3642E-2012 耐热的玻璃织物增强的热固树脂叠层塑料模制品

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of glass-cloth-reinforced thermosetting resin in the form of laminated, pressure-bag or matched-die moldings. These moldings have been used typically for parts requiring thermal stability consistent with good mechanical properties when exposed to temperatures up to 260 degrees C (500 degrees F) continuously or up to 315 degrees C (599 degrees F) intermittently, but usage is not limited to such applications.

Plastic Moldings, Laminated, Thermosetting Resin, Glass Cloth Reinforced, Heat Resistant

DIN EN 3844-2:2012 航空航天系列.非金属材料的可燃性.第2部分: 水平小型燃烧试验.水平火焰传播的测定.德文版和英文版 EN 3844-2-2011

Aerospace series - Flammability of non metallic materials - Part 2: Small burner test, horizontal - Determination of the horizontal flame propagation; German and English version EN 3844-2:2011

DIN EN 2824:2012 航空航天系列.热辐射及火焰辐射下非金属材料的燃烧.材料烟气中烟浓度及气体成分的测定.测试设备仪器和介质.德文版和英文版

Aerospace series - Burning behaviour of non-metallic materials under the influence of radiating heat and flames - Determination of smoke density and gas components in the smoke of materials - Test equipment apparatus and media; German and English version

DIN EN 3844-3:2012 航空航天系列.非金属材料可燃性.第3部分:45°小型燃烧试验.材料耐燃性,辉光传播和耐火焰穿透性测定.德文和英文版 EN 3844-3-2011

Aerospace series - Flammability of non metallic materials - Part 3: Small burner test, 45 - Determination of the resistance of material to flame and glow propagation and to flame penetration; German and English version EN 3844-3:2011

DIN EN 3844-1:2012 航空航天系列.非金属材料的可燃性.第1部分:垂直小型燃烧试验.垂直火焰传播的测定.德文版和英文版 EN 3844-1-2011

Aerospace series - Flammability of non metallic materials - Part 1: Small burner test, vertical - Determination of the vertical flame propagation; German and English version EN 3844-1:2011

ASTM E2461-12 航线控制塔操作室玻璃厚度测定标准实施规范

This standard procedure facilitates determination of the thickness of a glass construction required to resist a specified design load with a selected probability of breakage. This standard procedure addresses the following glass constructions: annealed monolithic, annealed laminated, and insulating glass fabricated with annealed monolithic or annealed laminated glass, or both. Use of these procedures assume: The glass is free of edge damage and is properly glazed, The glass has not been subjected to abuse, The surface condition of the glass is typical of glass that has been in service for several years, and is significantly weaker than freshly manufactured glass due to minor abrasions on exposed surfaces, The glass edge support system is sufficiently stiff to limit the lateral deflections of the supported glass edges to less than 1/175 of their lengths. The specified design load shall be used for this calculation, and The center of glass deflection shall not result in loss of edge support. Typically maintaining center of glass deflection at or below the magnitude of three times the nominal glass thickness assures that no loss of edge support will occur. Many other factors affect the selection of glass type and thickness. These factors include but are not limited to: thermal stresses, the effects of windborne debris, excessive deflections, behavior of glass fragments after breakage, seismic effects, heat flow, edge bite, noise abatement, potential post-breakage consequences, and so forth. In addition, considerations set forth in federal, state, and local building codes along with criteria presented in safety glazing standards and site specific concerns may control the ultimate glass type and thickness selection.1.1 This practice covers the determination of the thickness of glass installed in airport traffic control towers (ATCT) to resist a specified design loading with a selected probability of breakage less than or equal to either 1 lite per 1000 or 4 lites per 1000 at the first occurrence of the design wind loading. 1.2 The procedures apply to common outward sloping cab glass designs for which the specified loads do not exceed 10 kPa (210 psf). 1.3 The procedures assume control tower cab glass has an aspect ratio no greater than 2. 1.4 The procedures assume control tower cab glass has an area no less than 1.86 square metres (20 square feet). 1.5 The procedures apply only to annealed monolithic, annealed laminated, or annealed insulating glass having a rectangular or trapezoidal shape. 1.6 The use of the procedures assumes the following: 1.6.1 Annealed monolithic and annealed laminated glass installed in ATCTs shall have continuous lateral support along two parallel edges, along any three edges, or along all four edges; 1.6.2 Insulating glass shall have continuous lateral support along all four edges; and 1.6.3 Supported glass edges are simply supported and free to slip in plane. 1.7 The procedures do not apply to any form of wired, patterned, etched, sandblasted, or glass types with surface treatments that reduce the glass strength. 1.8 The procedures do not apply to any form of heat treated glass, chemically strengthened glass, or any type of glass with surface treatments intended to increase the glass strength. 1.9 The procedures address the determination of thickness and construction type to resist a specified design wind load at a selected probability of breakage. The final glass thickness and construction determined also depends upon a variety of other factors (see 5.3). 1.10 These procedures do not address blast loading on glass. 1.11 The values stated in SI units are to be regar......

Standard Practice for Determining the Thickness of Glass in Airport Traffic Control Tower Cabs

NF L17-123:2011 航空航天系列.丁腈橡胶.２３类.特性

Aerospace series - Butadiene - Acrylonitrile rubbers - Class 23 - Characteritics.

NF L17-132:2011 航空航天系列.氯丁橡胶.32类.特性

Aerospace series - Polychloroprene rubbers - Class 32 - Characteristics.