V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3564F-2011 硫化纤维板

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers vulcanized fiber in the form of sheet. This sheet has been used typically for gaskets and reinforcements on packaging enclosures, but usage is not limited to such applications.

Vulcanized Fiber Sheet

SAE AMS3336E-2011 55-65耐超低温的硅胶

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a silicone (PVMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts required to operate or seal from -85 to +230 degrees C (-121 to +446 degrees F), compounded especially for operation at extreme low temperatures, but usage is not limited to such applications. Silicone rubber is resistant to deterioration by weathering and by high-aniline-point petroleum-base oils and remains flexible over the temperature range noted. This material is not normally suitable for use in contact with low-aniline-point petroleum-base fluids, including fuels, due to excessive swelling.

Silicone (PVMQ) Rubber, Extreme Low Temperature Resistant, 55-65

SAE AMS3611E-2011 通用聚碳酸酯塑料板

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a polycarbonate resin in the form of sheet. This sheet has been used typically for parts, such as aircraft heating ducts, cabin liners, fairings, storage boxes, and decorative laminates, requiring high impact strength, high strength, and dimensional stability, but usage is not limited to such applications. This material is sensitive to some solvents; each application must be evaluated on its own metrics.

Plastic Sheet, Polycarbonate, General Purpose

SAE AMS-R-83285A-2011 通用乙丙橡胶

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers two grades of ethylene-propylene rubber having excellent resistance to ozone and hot water, but poor resistance to hydrocarbon oils or solvents.

Rubber, Ethylene-Propylene, General Purpose

SAE AMS3570F-2011 中等挠性开孔聚氨酯泡沫材料

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers two types of an open-cell, medium-flexibility polyurethane foam in the form of sheet, strip, and shapes. These products have been used typically for general interior padding, cushioning, and vibration insulation, but usage is not limited to such applications. Foam furnished to this specification shall be classified as follows: Type I - Polyurethane Foam - Easter and Type II - Polyurethane Foam - Ester. Type II shall be supplied unless Type I is ordered.

Foam, Flexible Polyurethane, Open Cell, Medium Flexibility

SAE AMS3229H-2011 75-85低膨胀的耐热油的丁腈(NBR)橡胶

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist.

Acrylonitrile Butadiene (NBR) Rubber, Hot Oil Resistant, Low Swell, 75-85

SAE AMS3626G-2011 异丁烯酸甲酯塑料模制品和挤压件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of methyl methacrylate in the form of extrusions, compression moldings, and injection moldings. These products have been used typically for parts requiring good dimensional stability, a high degree of optical clarity, and good resistance to outdoor weathering, but usage is not limited to such applications.

Plastic Moldings and Extrusions, Methyl Methacrylate

SAE AMS3632F-2011 收缩比为2:1的半刚性热收缩辐照聚偏二氟乙烯电气绝缘塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an irradiated, thermally-stabilized, flame-resistant, modified-polyvinylidene-fluoride plastic in the form of extra-thin-wall tubing. Primarily for use as a semi-rigid, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 175 degrees C (347 degrees F) or higher.

Tubing, Plastic, Electrical Insulation, Irradiated Polyvinylidene Fluoride, Semi-Rigid, Heat-Shrinkable, 2 to 1 Shrink Ratio

SAE AMS3615F-2011 棉织物增强酚醛树脂塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of cotton fabric impregnated with a phenolic resin and supplied in the form of tubing. This tubing has been used typically for electrical insulation at low voltages and for protection from galvanic corrosion, but usage is not limited to such applications. This tubing has good machining qualities and good moisture resistance.

Plastic Tubing Cotton Fabric Reinforced Phenol-Formaldehyde

SAE AMS3607G-2011 棉织物增强酚醛树脂塑料板

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers phenol/formaldehyde-resin-impregnated, cotton fabric laminates in the form of sheet. This sheet has been used typically for parts requiring good mechanical properties but where electrical properties are of secondary importance and no post-forming is required, but usage is not limited to such applications. Often used for fairleads and tubing supports.

Plastic Sheet, Cotton Fabric Reinforced Phenol-Formaldehyde

QJ 20057.2-2011 战术导弹用有机硅类高温防热涂层

Silicone-based high-temperature heat-resistant coating for tactical missiles

SAE AMS3262A-2011 -67至500℉(-55至260℃)使用的导电性和耐腐蚀(非铬酸盐)两部分硅橡胶密封胶剂

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a silicone, electrically conductive and corrosion-inhibiting sealing compound. This sealing compound has been used typically for electrical bonding and sealing bare aluminum alloy or chemical conversion coated aluminum alloy surfaces, but usage is not limited to such applications.

Sealing Compound, Silicone Rubber, Two-Part, Electrically Conductive and Corrosion Resistant (Nonchromated) for Use from -67 to 500°F (-55 to 260°C)

SAE AMS3571/7C-2011 55硬度计D未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, 55 Durometer D

SAE AMS3090B-2011 多硫化物密封剂兼容紧固件热凝固干膜润滑剂

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a dry film lubricant in the form of lubricating solids dispersed in a resin binder and suitable solvents to produce a sprayable liquid. This product has been used typically for lubrication of fasteners in the area of aircraft fuel tanks where contact with fuel tank sealants is likely, but usage is not limited to such applications.

Lubricant, Dry Film, Heat Cured, For Fasteners Polysulfide Sealant Compatible

SAE AMS3243G-2011 55-65耐燃的氯丁二烯(CR)橡胶

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as grommets, seals, and line supports, on the firewall of aircraft or wherever flame resistance is of prime importance, but usage is not limited to such applications. Each application should be considered individually.

Chloroprene (CR) Rubber Flame Resistant, 55-65

SAE AMS3249D-2011 75-85耐肼基流体的乙丙橡胶

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an ethylene propylene (EPDM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes other than o-rings. These products have been used typically for seals and gaskets for use from -55 to +70 °C (-67 to +158 °F) in hydrazine-base fluids, but usage is not limited to such applications.

Ethylene Propylene (EPDM) Rubber, Hydrazine-Base-Fluid Resistant, 75-85

SAE AMS3571/8C-2011 65硬度计D未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, 65 Durometer D

SAE AMS3571/4C-2011 75硬度计A未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, 75 Durometer A

SAE AMS3571/2C-2011 硬度计A未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, Durometer A

SAE AMS3571/6C-2011 95硬度计A未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, 95 Durometer A