V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3090B-2011 多硫化物密封剂兼容紧固件热凝固干膜润滑剂

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a dry film lubricant in the form of lubricating solids dispersed in a resin binder and suitable solvents to produce a sprayable liquid. This product has been used typically for lubrication of fasteners in the area of aircraft fuel tanks where contact with fuel tank sealants is likely, but usage is not limited to such applications.

Lubricant, Dry Film, Heat Cured, For Fasteners Polysulfide Sealant Compatible

SAE AMS3269C-2011 360℉(182℃)间歇性使用的高强度整体油箱和燃料电池腔聚硫(T)合成橡胶密封剂

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers three class of fuel-resistant polysulfide (T) sealing compound with high strength and temperature characteristics, supplied as a two-component system which cures at room temperature. This sealing compound has been used typically in sealing aircraft integral fuel tanks, fuel tank fillets and faying surfaces, pressure barriers and moldline surfaces, but usage is not limited to such applications. The sealing compound is resistant to jet fuels and is capable of withstanding long-term exposure from -65 to 250 °F (-54 to 121 °C) and short-term exposure (approximately 6 hours) to 360 °F (182 °C).

Sealing Compound, Polysulfide (T) Synthetic Rubber for Integral Fuel Tank and Fuel Cell Cavities High Strength, for Intermittent Use to 360°F (182°C)

SAE AMS3101B-2011 丙烯酸和聚碳酸酯的无裂纹聚硫化物密封剂的助粘剂

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared "NONCURRENT" by the Aerospace Materials Division, SAE, as of July 2009. It is recommended, therefore, that this specification not be specified for new designs. "NONCURRENT" refers to those specifications which have previously been widely used and which may be required for production or processing of existing designs in the future. The Aerospace Materials Division, however, does not recommend these specifications for future use in new designs.This specification covers adhesion promoters in liquid form. This product has been used typically for use in enhancing the adhesion of polysulfide adhesives of sealing compounds to acrylic and polycarbonate windshield materials, but usage it not limited to such applications.

Adhesion Promotoer for Polysulfide Sealants, Non-crazing of Acrylic and Polycarbonate

SAE AMS3383A-2011 75-85耐高温燃料和油的聚四氟乙烯-氟硅氧烷橡胶

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a polytetrafluoroethylene (PTFE) modified fluorosilicone (FVMQ) rubber in the form of molded shapes, molded rings (ASTM D 1414), and compression seals. These products have been used typically for parts requiring resistance to jet fuel and lubricating oils, but usage is not limited to such applications. Generally, products are usable over a temperature range of -60 to +150 degrees C (-76 to +302 degrees F); the high tear resistance improves installation characteristics and the high tensile stress (modulus) enhances extrusion resistance. Each application, however, has to be considered individually.

Polytetrafluoroethylene (PTFE), Fluorosilicone (FVMQ) Rubber High Temperature Fuel and Oil Resistant 75 to 85

SAE AMS3258A-2011 适用于300℉ (149℃)的飞机挡风玻璃和座舱罩用聚硫醚密封剂

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a polythioether based sealing compound supplied as a two-component system suitable for application by brush, or by extrusion gun or spatula. This production has been used typically for sealing aircraft windshields and canopies. This includes both sealing between the windshield/canopy and the aircraft structure for pressure sealing, and sealing around the windshield/canopy for weather sealing, but usage is not limited to such applications. The sealing compound cures at room temperature and may have an accelerated cure at higher temperatures. The sealing compounds are usable from -65 to 300 °F (-54 to 149 °C).

Sealing Compound, Polythioether For Aircraft Windshields and Canopies, For Use Up to 300°F (149°C)

SAE AMS3571/2C-2011 硬度计A未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, Durometer A

SAE AMS3571/8C-2011 65硬度计D未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, 65 Durometer D

SAE AMS3249D-2011 75-85耐肼基流体的乙丙橡胶

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an ethylene propylene (EPDM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes other than o-rings. These products have been used typically for seals and gaskets for use from -55 to +70 °C (-67 to +158 °F) in hydrazine-base fluids, but usage is not limited to such applications.

Ethylene Propylene (EPDM) Rubber, Hydrazine-Base-Fluid Resistant, 75-85

SAE AMS3571/9C-2011 75硬度计D未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, 75 Durometer D

SAE AMS3571C-2011 未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled

SAE AMS-I-7171A-2011 热声学绝缘毯

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers the requirements of composite blankets suitable for acoustical and thermal insulation of the walls of aircraft compartments within the temperature range of -65 °F to +175 °F (-54 °C to +80 °C).

Insulation Blanket, Thermal-Acoustical

SAE AMS3252K-2011 一般用途的坚固合成橡胶和软木复合物

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers a synthetic rubber and cork composition in the form of sheet, strip, and molded shapes. This product has been used typically for parts, such as packings, seals, grommets, line support blocks, and tank strap pads, where cushioning and vibration damping are of prime importance, but usage is not limited to such applications.

Synthetic Rubber and Cork Composition General Purpose, Firm

SAE AMS3571/6C-2011 95硬度计A未充填实心柔性聚醚氨基甲酸乙酯(EU)树脂铸件

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products. Primarily for liquid application as electronics encapsulation or for casting parts and shapes.

Resin, Polyether Urethane (EU) Casting Flexible, Solid, Unfilled, 95 Durometer A

SAE AMS3108G-2011 底漆,赭色,酚醛

This document has been declared "Stabilized" and will no longer be subjected toperiodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification has been declared "CANCELLED" by the Aerospace Materials Division, SAE, as of June 2009. By this action, this document will remain listed in the Numerical Section of the Index of Aerospace Material Specifications indicating that it has been "CANCELLED".

Primer, Ocher, Phenolic

SAE AMS3587E-2011 收缩率为2-1的热收缩(低回复温度)极高挠性的着色的辐照处理的电绝缘聚烯烃塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of a thin-wall, heat-shrinkable tubing with a low recovery temperature. This tubing has been used typically as a very flexible, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 100 °C (212 °F) or higher, but usage is not limited to such applications. This tubing is stable for continuous exposure from -55 to +135 °C (-67 to +275 °F).

Plastic Tubing, Electrical Insulation, Irradiated Polyolefin, Pigmented, Very Flexible, Heat Shrinkable Low Recovery Temperature 2 to 1 Shrink Ratio

SAE AMS3960-2011 先进复合预浸料坯.公称250℉固化.碳素纤维和环氧树脂单向带

This specification establishes the requirements for a nominal 250 °F cure epoxy preimpregnated carbon fiber unidirectional tape product. This material is intended for use in laminate applications with a service temperature of -65 to 180 °F. The composite may be used for the manufacture of primary and secondary aircraft structure. The purpose of this specification is to allow procurement of a defined material corresponding to the statistically derived material properties published in MIL-HDBK-17.

Advanced Composites Prepreg - Nominal 250 °F Cure - Carbon Fiber and Epoxy Resin, Unidirectional Tape

SAE AMS3588E-2011 收缩率为2-1的热收缩极高挠性的透明的辐照处理的电绝缘聚烯烃塑料管

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of thin-wall, heat-shrinkable tubing with a low recovery temperature. This tubing has been used typically as a very flexible, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 100 °C (212 °F) or higher, but usage is not limited to such applications. This tubing is stable for continuous exposure from -55 to +135 °C (-67 to +275 °F).

Plastic Tubing, Electrical Insulation, Irradiated Polyolefin, Clear, Very Flexible, Heat Shrinkable 2 to 1 Shrink Ratio

SAE AMS3240K-2011 35-45耐风化的氯丁二烯(CR)橡胶

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as window channels, bumper pads, chafing strips, and seals, requiring resistance to weather and for use from -40 to +212 °F (-40 to +100 °C), but usage is not limited to such applications.

Chloroprene (CR) Rubber, Weather Resistant, 35-45

SAE AMS3568/1B-2011 密度5 lb/cu ft(80 kg/m<(hoch)3>)的缓冲用聚醚氨基甲酸乙酯(EU)橡胶泡沫

This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet. Primarily for use in applications where shock absorbing characteristics and cushioning are required and where flammability does not preclude its use.

Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing, 5 lb/cu ft (80 kg/m<(hoch)3>) Density

SAE AMS3568/3B-2011 密度20 lb/cu ft (320 kg/m<(hoch)3>)的缓冲用聚醚氨基甲酸乙酯(EU)橡胶泡沫

This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet. Primarily for use in applications where shock absorbing characteristics and cushioning are required and where flammability does not preclude its use.

Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing, 20 lb/cu ft (320 kg/m<(hoch)3>) Density