V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3568/3B-2011 密度20 lb/cu ft (320 kg/m<(hoch)3>)的缓冲用聚醚氨基甲酸乙酯(EU)橡胶泡沫

This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet. Primarily for use in applications where shock absorbing characteristics and cushioning are required and where flammability does not preclude its use.

Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing, 20 lb/cu ft (320 kg/m<(hoch)3>) Density

SAE AMS3568/2B-2011 密度15 lb/cu ft (240 kg/m<(hoch)3>)的缓冲用聚醚氨基甲酸乙酯(EU)橡胶泡沫

This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet. Primarily for use in applications where shock absorbing characteristics and cushioning are required and where flammability does not preclude its use.

Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing, 15 lb/cu ft (240 kg/m<(hoch)3>) Density

SAE AMS3240K-2011 35-45耐风化的氯丁二烯(CR)橡胶

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as window channels, bumper pads, chafing strips, and seals, requiring resistance to weather and for use from -40 to +212 °F (-40 to +100 °C), but usage is not limited to such applications.

Chloroprene (CR) Rubber, Weather Resistant, 35-45

SAE AMS3599B-2011 可燃性受控的覆铜箔玻璃纤维织物增强的环氧树脂塑料薄板

This specification covers epoxy-resin-impregnated glass fabric laminates in the form of sheet clad on one or both sides with electrolytically-deposited copper foil. Primarily for use in etched, printed circuits used in electrical and electronic equipment where low moisture absorption and superior bond strength are required.

Plastic Sheet, Copper-Faced, Glass Fabric Reinforced Epoxy Resin, Flammability Controlled

SAE AMS3241J-2011 55-65耐风化的氯丁二烯(CR)橡胶

This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as window channels, bumper pads, chafing strips, and seals, requiring resistance to weather and for use from -40 to +212 °F (-40 to +100 °C), but usage is not limited to such applications.

Chloroprene (CR) Rubber, Weather Resistant, 55-65

SAE AMS3756C-2011 烧结的25级75%聚四氟乙烯树脂，填充聚四氟乙烯的玻璃纤维模制品

This specification covers one grade of glass-fiber-filled polytetrafluoroethylene (PTFE) in the form of molded billets. Primarily for parts, such as seals and back-up rings, requiring chemical inertness and superior mechanical properties up to 500 degrees F (260 degrees C).

Moldings, Glass Fiber Filled Polytetrafluoroethylene, 75% PTFE Resin, 25 Glass, As Sintered

SAE AMS3272B-2011 射频或超声密封热聚氨酯涂覆的尼龙布

This specification and its supplementary detail specification cover a woven nylon cloth coated with polyether (EU) urethane. Primarily for use in inflatable survival equipment requiring a cloth which is thermally, radio frequency, or ultrasonically sealable and having air holding characteristics.

Cloth, Nylon, Polyurethane Coated, Thermally, Radio Frequency, or Ultrasonically Sealable

SAE AMS3623E-2011 收缩率为1,750:1的热收缩挠性辐照处理的电绝缘弹性管

This specification covers an irradiated, thermally-stabilized, flame-resistant modified-polychloroprene rubber in the form of thin-wall tubing. This tubing has been used typically as a flexible, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 135 degrees C (275 degrees F) or higher, but usage is not limited to such applications.

Elastomeric Tubing, Electrical Insulation, Irradiated Polychloroprene, Flexible, Heat-Shrinkable, 1.750 to 1 Shrink Ratio

SAE AMS3657F-2011 已烧结的高强度聚四氟乙烯(PTFE)挤压型材

This specification covers one grade of polytetrafluoroethylene (PTFE) in the form of extruded and sintered rods, tubes, and profiles. These products have been used typically for parts, such as bushings and insulators, requiring chemical inertness up to 500 °F (260 °C) and better mechanical and/or electrical properties than AMS 3656, but usage is not limited to such applications. When improved dimensional stability is required, it is recommended that stress relieved product in accordance with AMS 3659 be specified. For parts such as seals, back-up rings and bearings that do not require dielectric properties and radiographic inspection it is recommended to use AMS 3678/1 Grade B.

Polytetrafluoroethylene (PTFE) Extrusions, Premium Strength, As Sintered

SAE AMS3726/3B-2011 充填液态预催化树脂化合物的垫片

This specification covers a filled, resinous, thermosetting, precatalyzed, liquid compound capable of being applied and cured in place between the surfaces of mechanically fastened (joined) structures. This product has been used typically as a molded shim during assembly of aircraft components and parts, but usage is not limited to such applications. The compound covered by this detail specification requires storage in the frozen condition just prior to installation.

Shims, Filled Resin Compound Liquid Precatalyzed

SAE AMS3272/2B-2011 4.0盎司/平方码(135 g/m<(hoch)2>)涂覆聚氨酯的平纹尼龙织物

This specification covers a woven nylon cloth coated with polyether (EU) urethane. Primarily for use in inflatable survival equipment.

Cloth, Nylon, Polyurethane Coated, Plain Weave, 4.0 ounces/square yard (135 g/m<(hoch)2>)

SAE AMS3667E-2011 烧结的一般用途的聚四氟乙烯(PTFE)模压板

This specification covers virgin, unfilled polytetrafluoroethylene (PTFE) in the form of sheet, manufactured by compression molding and sintering. This sheet has been used typically for mechanical parts such as insulation, seals, and bearings, requiring chemical inertness up to 500 °C (260 °F), but usage is not limited to such applications.

Polytetrafluoroethylene (PTFE) Sheet, Molded, General Purpose Grade, AS Sintered

SAE AMS3668E-2011 烧结的优质聚四氟乙烯(PTFE)模制品

This specification covers two types of virgin, unfilled polytetrafluoroethylene (PTFE) in the form of molded rods, tubes, and shapes. This specification does not apply to product over 12 inches (305 mm) in length, rods under 0.750 inch (19.05 mm) in diameter, and tubes having wall thickness under 0.500 inch (12.70 mm). These moldings have been used typically for parts requiring chemical inertness up to 500 °F (206 °C), and better mechanical and/or electrical properties than AMS 3660, but usage is not limited to such applications. for applications such as bearings, seals, and back-up rings that do not require dielectric properties it is recommended to use AMS 3678/1 GradeA.

Polytetrafluoroethylene (PTFE) Moldings, Premium Grade, As Sintered

SAE AMS3274H-2011 耐燃料的尼龙织物增强的丁腈橡胶薄板和模制型材

This specification covers nylon-cloth-reinforced acrylonitrile - butadiene (NBR) rubber in the form of sheet and of shapes molded and cured form partly cured sheet. Primarily for diaphragms in power plant fuel supply and control systems.

Acrylonitrile Butadiene (NBR) Rubber Sheet and Molded Shapes Nylon Cloth Reinforced Fuel Resistant

SAE AMS3660E-2011 烧结的通用等级聚四氟乙烯(PTFE)模型

This specification covers virgin, unfilled, polytetrafluoroethylene (PTFE) in the form of molded rods, tubes, and shapes. This specification does not apply to product over 12 inches (305 mm) in dimension parallel to the direction of applied molding pressure, rods under 0.750 inch (19.05 mm) in diameter, and tubes having wall thickness under 0.500 inch (12.70 mm). These moldings have been used typically for parts such as, bushings and insulators, requiring chemical inertness and good mechanical and electrical properties up to 500 °C (260 °F), but usage is not limited to such applications. For applications such as bearins, seals, and back-up rings that do not require dielectric properties it is recommended to use AMS 3678/1 Grade A.

Polytetrafluoroethylene (PTFE) Moldings, General Purpose Grade, As Sintered

SAE AMS3677A-2011 烧结和聚四氟乙烯(PTFE)浸渍的聚苯并咪唑(PBI)聚酰胺玻璃纤维织物

This specification covers a polybenzimidazole (PBI) polyamide fiberglass fabric impregnated with polytetrafluoroethylene (PTFE) in the form of woven sheet or strip or of braided tubing. This fabric has been used typically for anti-chafing cushion between parts, such as flexible metal tubes and tube clips, rub strips, gaskets, and air seals, requiring long-term heat resistance up to 290 degrees C (554 degrees F), but usage is not limited to such applications.

Fabric, Polybenzimidazole (PBI) Polyamide Fiberglass Polytetrafluoroethylene (PTFE) Impregnated, Sintered

SAE AMS3273F-2011 耐风化的尼龙布增强氯丁(CR)橡胶薄板

This specification covers nylon-cloth-reinforced chloroprene (CR) rubber in the form of sheet. This product has been used typically for parts, such as gaskets, seals, diaphragms, and chafing strips, requiring resistance to weather, ozone, moderate heat, low temperature, water, and petroleum-base lubricating oil, but usage is not limited to such applications.

Chloropene (CR) Rubber Sheet, Nylon Cloth Reinforced, Weather Resistant

SAE AMS3643C-2011 热固化玻璃纤维无捻粗纱填充的有机硅塑料耐热模制品

This specification covers a glass-roving-filled silicone resin in the form of compression moldings or transfer moldings. These products have been used typically for parts requiring good mechanical and electrical properties and thermal stability in continuous service up to 315 degrees C (599 degrees F) or intermittent service up to 370 degrees C (698 degrees F), but usage is not limited to such applications.

Plastic Moldings, Silicone, Thermosetting Glass Roving Filled, Heat Resistant

SAE AMS3270K-2011 耐风化的棉织物增强的氯丁二烯(CR)橡胶薄板

This specification covers cotton-fabric-reinforced chloroprene (CR) rubber in the form of sheet. Primarily for parts, such as gaskets and seals, requiring resistance to weather, moderate heat, water, and petroleum-base lubricating oil.

Chloroprene (CR) Rubber Sheet, Cotton Fabric Reinforced, Weather Resistant

SAE AMS3286F-2011 白色100%羊毛毡的厚实衬垫

This specification covers felted wool fibers in the form of sheets and rolls. This product has been used typically for oil and grease retention where the felt is confined and compressed in assembly and for dust shields where conditions are not severe, but usage is not limited to such applications.

Felt, Firm Pad, White 100% Wool