V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3658F-2011 射线照相检查的高强度已烧结和消除应力的聚四氟乙烯(PTFE)挤压型材

This specification covers virgin unfilled polytetrafluoroethylene (PTFE) in the form of extruded rods, tubes, and shapes. These products have been used typically for parts, such as insulators and bushings requiring chemical inertness and dimensional stability up to 500 °F (260 °C) and better mechanical and/or electrical properties than AMS 3656, but usage is not limited to such applications. for applications such as seals, back-up rings and bearings that do not require dielectric properties and radiographic inspection it is recommended to use AMS 3678/1 Grade B.

Polytetrafluoroethylene (PTFE) Extrusions, Premium Strength, Sintered and Stress- Relieved Radiographically Inspected

SAE AMS3660E-2011 烧结的通用等级聚四氟乙烯(PTFE)模型

This specification covers virgin, unfilled, polytetrafluoroethylene (PTFE) in the form of molded rods, tubes, and shapes. This specification does not apply to product over 12 inches (305 mm) in dimension parallel to the direction of applied molding pressure, rods under 0.750 inch (19.05 mm) in diameter, and tubes having wall thickness under 0.500 inch (12.70 mm). These moldings have been used typically for parts such as, bushings and insulators, requiring chemical inertness and good mechanical and electrical properties up to 500 °C (260 °F), but usage is not limited to such applications. For applications such as bearins, seals, and back-up rings that do not require dielectric properties it is recommended to use AMS 3678/1 Grade A.

Polytetrafluoroethylene (PTFE) Moldings, General Purpose Grade, As Sintered

SAE AMS3643C-2011 热固化玻璃纤维无捻粗纱填充的有机硅塑料耐热模制品

This specification covers a glass-roving-filled silicone resin in the form of compression moldings or transfer moldings. These products have been used typically for parts requiring good mechanical and electrical properties and thermal stability in continuous service up to 315 degrees C (599 degrees F) or intermittent service up to 370 degrees C (698 degrees F), but usage is not limited to such applications.

Plastic Moldings, Silicone, Thermosetting Glass Roving Filled, Heat Resistant

SAE AMS3285F-2011 白色100%羊毛毡的背面检查

This specification covers felted wool fibers in the form of sheets and rolls. This product has been used typically for oil retention in installations which do not compress the felt, for feeding low-viscosity or light oil, and where unusual strength and hardness are required for such parts as washers, bushings, wicks, and other parts where resistance to wear and abrasion are required, but usage is not limited to such applications.

Felt, Back Check, White 100% Wool

SAE AMS3271B-2011 涂覆氯丁橡胶可伸展的尼龙织物

This specification covers a polychloroprene-coated, one side only, nylon knit in the form of cloth. Primarily for use in fabrication of protective clothing.

Cloth, Knitted Nylon Stretch, Polychloroprene Coated

SAE AMS3573C-2011 80至90耐低温实心的挠性聚醚型聚亚氨酯(EU)树脂铸件

This specification covers a plasticized, polyether-type, urethane (EU) resin and hardener which, when mixed and cured, produces elastomeric polyurethane products. This resin has been used typically for applications, such as electronic encapsulation or for casting parts and shapes, requiring exceptional flexibility down to -55 degrees C (-67 degrees F) where poor reversion resistance can be tolerated, but usage is not limited to such applications.

Resin, Polyurethane (EU), Casting, Polyether-Type, Flexible, Solid, Low-Temperature Resistant 80 to 90

SAE AMS3272/2B-2011 4.0盎司/平方码(135 g/m<(hoch)2>)涂覆聚氨酯的平纹尼龙织物

This specification covers a woven nylon cloth coated with polyether (EU) urethane. Primarily for use in inflatable survival equipment.

Cloth, Nylon, Polyurethane Coated, Plain Weave, 4.0 ounces/square yard (135 g/m<(hoch)2>)

SAE AMS3272/1B-2011 6.0盎司/平方码(200 g/m<(hoch)2>)涂覆聚氨酯的平纹尼龙织物

This specification covers a woven nylon cloth coated with polyether (EU) urethane. Primarily for use in inflatable survival equipment.

Cloth, Nylon, Polyurethane Coated, Plain Weave, 6.0 ounces/square yard (200 g/m<(hoch)2>)

SAE AMS3659F-2011 已烧结和消除应力的高强度聚四氟乙烯(PTFE)挤压型材

This specification covers virgin, unfilled polytetrafluoroethylene (PTFE) in the form of extruded rods, tubes, and profiles. These products have been used typically for parts, such as bushings and insulators, requiring better chemical inertness and dimensional stability up to 500 °F (260 °C) than AMS 3657 and better mechanical and electrical properties than AMS 3656, but usage is not limited to such applications. For spplications such as bearings, seals, and back-up rings that do not require dielectric properties it is recommended to use AMS 3678/1 Grade B.

Polytetrafluoroethylene (PTFE) Extrusions, Premium Strength, Sintered and Stress-Relieved

SAE AMS3270K-2011 耐风化的棉织物增强的氯丁二烯(CR)橡胶薄板

This specification covers cotton-fabric-reinforced chloroprene (CR) rubber in the form of sheet. Primarily for parts, such as gaskets and seals, requiring resistance to weather, moderate heat, water, and petroleum-base lubricating oil.

Chloroprene (CR) Rubber Sheet, Cotton Fabric Reinforced, Weather Resistant

DIN EN 2757:2011 航空航天系列.结构型胶粘剂系统.试验方法.底漆干残留物和灼烧残留物的测定;德文版本和英文版本EN 2757-2011

Aerospace series - Structural adhesives system - Test method - Determination of the drying and ignition residues of primers; German and English version EN 2757:2011

BS EN 4593:2011 航空航天系列.色漆和清漆 太阳能吸收率的测定

This European Standard specifies the method of test for determining the solar absorptance of paints and varnishes. The test procedure determines the amount of energy reflected by the material in the range of wavelengths at which there is energy from the sun hitting the Earth’s surface, and with the aid of a standard solar spectrum it allows a calculation to determine the solar absorptance which can then be used to determine the efficiency of solar heat reflecting paints. The procedure is applicable to products intended for use in aerospace applications.

Aerospace series. Paints and varnishes. Determination of solar absorptance

HB 5339-2011 金属结构胶接质量控制

本标准规定了金属结构胶接的人员、设备、仪表及工装、材料、工艺过程、环境、文件与资料等要求。 本标准适用于金属结构胶接的质量控制。

Quality control for structural adhesively-bonding of metals

HB/Z 63.2-2011 航空透明件柔性连接用胶粘剂配制及使用.第2部分: SY-50s胶粘剂

本部分规定了SY-50s胶粘剂配制及使用的材料、设备、仪器、环境、配制工艺、使用工艺、检验、安全与卫生等。 本部分适用于SY-50s胶粘剂的配制和使用。

Preparation and application process of adhesive used in flexible joint of aircraft transparency.Part 2:SY-50s adhesive

QJ 20020-2011 火箭发动机涡轮泵碳/碳密封材料规范

本规范规定了火箭发动机涡轮泵用B-1型碳/碳密封材料的要求、质量保证规定及交货准备等。 本规范适用于火箭发动机涡轮泵用B-1型碳/碳密封材料（以下简称密封材料）的检验与验收。其它碳/碳密封材料也可参照使用。

Specification for carbon/carbon sealing material used in turbopump of rocket engine

HB 20078-2011 航空用树脂基复合材料性能数据通用要求

本标准规定了航空用树脂基复合材料规范、许用值和设计的性能数据要求。 本标准适用于航空飞行器用树脂基复合材料规范、许用值及设计的性能项目选取。

General requirements for properties data of resin matrix composites for aerocraft

HB 20077-2011 航空用氟硅类密封剂规范

本规范规定了航空用氟硅类密封剂的要求、质量保证规定、交货准备及说明事项。本规范适用于航空用氟硅类密封剂。

Specification for fluorosilicone sealants for aviation

QJ 20026-2011 蜂窝夹层结构修补通则

本标准规定了铝蜂窝夹层结构（铝面板、铝蜂窝芯子）典型缺陷/损伤修补的-般要求、详细要求、质量控制及交付、贮存、运输等要求。 本标准适用于铝蜂窝夹层结构典型缺陷/损伤的修补（含无损检测）。其他种类蜂窝夹层结构典型缺陷/损伤的修补可参照使用。

General rules for honeycomb-sandwich structures repairing

QJ 20057.1-2011 战术导弹用有机硅类高温防热涂层

本部分规定了戰術導彈用GRW系列有機硅類高溫防熱塗料 (GRW-1防熱塗料、GRWN-1防熱膩 子) 的要求、质量保证规定、交货准备和说明事项。 本部分适用于战术导弹用GRW系列有机硅类高温防热涂料的生产及验收。

Silicone-based high-temperature heat-resistant coating for tactical missiles

QJ 20027-2011 导热脂低温热导率测试方法

本标准规定了用热线法在195K～300K温度区间内测试导热脂热导率的原理、测试装置及要求、测试环境条件、试样与安装要求、标准试样测试程序、试样测试程序、数据处理、装置的自校准、测试报告等要求。 本标准适用于热导率数值在0.05W/(m•k)～1.00W/(m•k)范围内的各种导热脂的测试。其他导热流体低温热导率的测试亦可参照使用。

Test method for thermal conductivity of thermal conductive grease at low temperature