V13 航空与航天用非金属材料 标准查询与下载

QJ 20027-2011 导热脂低温热导率测试方法

本标准规定了用热线法在195K～300K温度区间内测试导热脂热导率的原理、测试装置及要求、测试环境条件、试样与安装要求、标准试样测试程序、试样测试程序、数据处理、装置的自校准、测试报告等要求。 本标准适用于热导率数值在0.05W/(m•k)～1.00W/(m•k)范围内的各种导热脂的测试。其他导热流体低温热导率的测试亦可参照使用。

Test method for thermal conductivity of thermal conductive grease at low temperature

HB/Z 63.2-2011 航空透明件柔性连接用胶粘剂配制及使用.第2部分: SY-50s胶粘剂

本部分规定了SY-50s胶粘剂配制及使用的材料、设备、仪器、环境、配制工艺、使用工艺、检验、安全与卫生等。 本部分适用于SY-50s胶粘剂的配制和使用。

Preparation and application process of adhesive used in flexible joint of aircraft transparency.Part 2:SY-50s adhesive

HB/Z 63.1-2011 航空透明件柔性连接用胶粘剂配制及使用.第1部分: 丙烯酸酯胶粘剂及改性丙烯酸酯胶粘剂

本部分规定了丙烯酸酯胶粘剂及改性丙烯酸酯胶粘剂配制及使用的材料、设备、仪器、环境、配制工艺、使用工艺、检验、安全与卫生等。 本部分适用于丙烯酸酯胶粘剂及改性丙烯酸酯胶粘剂的配制和使用。

Preparation and application process of adhesive used in flexible joint of aircraft transparency.Part 1:Acrylic adhesive and modified acrylic adhesive

HB/Z 63.3-2011 航空透明件柔性连接用胶粘剂配制及使用.第3部分: J-189胶粘剂

本部分规定了J-189胶粘剂配制及使用的材料、设备、仪器、环境、配制工艺、胶接工艺、检验、安全与卫生等。 本部分适用于J-189胶粘剂的配制和使用。

Preparation and application process of adhesive used in flexible joint of aircraft transparency.Part 2: J-189 adhesive

DIN EN 2825:2011 航空航天系列.受火焰和辐射热影响的非金属材料的燃烧性能.烟浓度的测定;德文和英文版本EN 2825-2011

This European Standard defines a test method for determination of the smoke density due to pyrolitic decomposition of solid materials and composite materials of up to 25 mm in thickness under the influence of radiant heat only or with simultaneous flame application.

Aerospace series - Burning behaviour of non metallic materials under the influence of radiating heat and flames - Determination of smoke density; German and English version EN 2825:2011

DIN EN 4160:2011 航空航天系列.色漆和清漆.热辐射量影像的测定;德文版本和英文版本EN 4160-2011

This European Standard specifies the method of test for determining the resistance of paints and varnishes to the effects of heat or cold within the limits of - 50 °C to 200 °C. The test procedure assesses the resistance of paint coatings, varnishes or related products to changes of gloss, colour, blistering, cracking and/or detachment from the substrate as a result of exposure to elevated or sub ambient temperature. The procedure is applicable to products intended for use in aerospace applications.

Aerospace series - Paints and varnishes - Determination of the effect of thermal exposure; German and English version EN 4160:2011

SAE AMS3801/2B-2011 特殊编织的布制降落伞含元纤维和低模量重量为6.5(220)

This specification covers one weight and one weave of low-modulus meta-aramid cloth. Primarily for use in construction of parachutes.

Cloth, Parachute, Meta-Aramid, Low Modulus, 6.5 (220) Weight, Special Weave

SAE AMS3801/1B-2011 斜纹布制降落伞含元纤维和低模量重量为4.7(159)

This specification covers one weight and one weave of low-modulus meta-aramid cloth. Primarily for use in construction of parachutes.

Cloth, Parachute, Meta-Aramid, Low Modulus, 4.7 (159) Weight, Twill

SAE AMS3301H-2011 通用40硬度计硅橡胶

This specification covers a silicone rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. This product has been used typically for parts required to operate or seal from -85 to +401 °F (-65 to +205 °C). Silicone elastomer is resistant to deterioration by weathering and petroleum-base lubricating oil and remains flexible over the temperature range noted, but usage is not limited to such applications. These products are not normally suitable for use in contact with gasoline or aromatic fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the elastomer.

Silicone Rubber, General Purpose, 40 Durometer

SAE AMS3302H-2011 50硬度计的通用型硅橡胶

This specification covers a silicone rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. This product has been used for parts required to operate or seal from -85 to +401 °F (-65 to +205 °C). Silicone elastomer is resistant to deterioration by weathering and petroleum-base lubricating oil and remains flexible over the temperature range noted, but usage is not limited to such applications. These products are not normally suitable for use in contact with gasoline or aromatic fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the elastomer.

Silicone Rubber, General Purpose, 50 Durometer

SAE AMS3801/3B-2011 重量为12.0(407)的特殊编织低模量元纤维降落伞布料

This specification covers one weight and one weave of low-modulus meta-aramid cloth. Primarily for use in construction of parachutes.

Cloth, Parachute, Meta-Aramid, Low Modulus, 12.0 (407) Weight, Special Weave

SAE AMS3801C-2011 低模量间位芳纶降落伞布料

This specification covers a low modulus meta-aramid in the form of cloth. These products have been used typically used in construction of parachutes, but usage is not limited to such applications.

Cloth, Parachute - Meta-Aramid, Low Modulus

SAE AMS3801/4B-2011 重量为7.0(237)的平纹编织低模量元纤维降落伞布料

This specification covers one weight and one weave of low-modulus meta-aramid cloth. Primarily for use in construction of parachutes.

Cloth, Parachute, Meta-Aramid, Low Modulus, 7.0 (237) Weight, Plain Weave

SAE AMS3303K-2011 通用60硬度计硅橡胶

This specification covers a silicone rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. This product has been used typically for parts required to operate or seal from -85 to +401 °F (-65 to +205 °C). Silicone elastomer is resistant to deterioration by weathering and petroleum-base lubricating oil and remains flexible over the temperature range noted, but usage is not limited to such applications. These products are not normally suitable for use in contact with gasoline or aromtic fuels and low-aniline-point petroleum-base fluids due to excessive swelling of the elastomer.

Silicone Rubber, General Purpose, 60 Durometer

SAE AMS3801/5B-2011 重量为18.0(610)的经过树脂处理的篮子编织低模量元纤维降落伞布料

This specification covers one weight and one weave of low-modulus resin treated meta-aramid cloth. Primarily for use in construction of parachutes.

Cloth, Parachute, Meta-Aramid, Low Modulus, 18.0 (610) Weight, Basket Weave, Resin Treated

SAE AMS3217/4B-2011 测试板,氟橡胶(FKM),65-75

This specification covers a standard fluoroelastomer (FKM) rubber stock in the form of molded test slabs.

Test Slabs, Fluoroelastomer (FKM), 65-75

SAE AMS2515F-2011 聚四氟乙烯(PTFE)树脂涂料,低建造,370至400℃(698℉至 752℉)融合

This specification establishes the engineering requirements for producing thin coatings of polytetrafluoroethylene (PTFE) resin on parts and the properties of such coatings. Primarily to provide dry lubrication, high heat stability, and corrosion protection on parts which operate at not higher than 275 °C (527 °F) for limited periods or not higher than 245 °C (473 °C) for extended periods. This coating may also be used as a release film for molds.

Polytetrafluoroethylene (PTFE) Resin Coating, Low Build, 370 to 400°C (698 to 752°F) Fusion

SAE AMS7276H-2011 橡胶:氟橡胶(FKM)高温燃料和密封在燃油系统和特殊内燃机油系统里的抗油剂

This specification covers a fluorocabron (FKM) rubber in the form of O-rings, compression seals, O-ring cord and molded in place gaskets. These rings have been used typically as sealing rings, compression seals, O-ring cord and molded-in-place gaskets in contact with air or a variety of fuels, lubricants and specific hydraulic fluids from -20 to +400 °F (-29 to +240 °C), but usage is not limited to such applications. Each application should be considered individually. This class of fluoroelastomers may not be suitable for use in some high temperature stabized, "HTS", engine oils. Each "HTS" oil should be evaluated separately. Examples of "HTS" oils are those oils conforming to MIL-PRF-23699 Class HTS, MIL-PRF-7808 Grade 4, and AS5780 Class HPC.

Rubber: Fluorocarbon (FKM) High-Temperature-Fluid Resistant Low Compression Set For Seals in Fuel Systems and Specific Engine Oil Systems

SAE AMS7273D-2011 橡胶: 氟硅橡胶(FVMQ)高温燃料和密封在燃油系统和特殊内燃机油系统里的抗油剂

This specification covers a fluorosilicone (FVMQ) rubber in the form of molded rings. This product has been typicallyused -67 to +347 °F (-55 to +175 °C) in fuels and from -67 to +302 °F (-55 to +150 °C) in lubricating oils. This product is not recommended for use in most synthetic turbine lubricants, particularly high temperature stabilized. "HTS", engine oils (those confirming to MIL-PRF-23699 Class HTS, MIL-PRF-7808 Grade 4 and AS5780 Class HPC). The cross-section of such rings is usually not over 0.275 inch (6.98 mm) in diameter or thickness, but usage is not limited to such applications.

Rubber: Fluorosilicone (FVMQ) High Temperature Fuel and Oil Resistant For Seals in Fuel Systems and Specific Engine Oil Systems

BS EN 4160:2011 航空航天系列.涂料和清漆.热暴露效应的测定

This European Standard specifies the method of test for determining the resistance of paints and varnishes to the effects of heat or cold within the limits of − 50 °C to 200 °C. The test procedure assesses the resistance of paint coatings, varnishes or related products to changes of gloss, colour, blistering, cracking and/or detachment from the substrate as a result of exposure to elevated or sub-ambient temperature. The procedure is applicable to products intended for use in aerospace applications.

Aerospace series. Paints and varnishes. Determination of the effect of thermal exposure