V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3277F-2010 密封胶,聚硫醚橡胶,为整体油箱和通用快速固化,间歇使用360F(182C)

This specification covers polythioether rubber fuel resistant sealing compounds supplied as a two component system which cures at room temperature. This product has been used in aircraft integral fuel tanks for repair of fillet and fastener seals and faying surface seals as well as initial sealing of faying surfaces, overcoating of fasteners, and sealing of seams and joints, for service from -80 to +320°F (-62 to +160°C), with short-term recurring exposures (approximately six hours) up to 360°F (182°C), but usage is not limited to such applications. This product is not recommended for use on aircraft windshields or canopies or other applications where crazing or degradation of plastic components may occur. Sealing compound must be applied at temperatures above 50°F (10°C), but will cure at lower temperatures.

Sealing Compound, Polythioether Rubber, Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360F (182C)

SAE ARP5316C-2010 包含优先于五金器具的合成橡胶元件人造橡胶密封和密封剂配件的储存

This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents. However, when the requirements of this document are in conflict with the customer's requirements or specifications, the requirements of the customer's detailed specification shall govern

Storage of Elastomeric Seals and Seal Assemblies Which Include an Elastomer Element Prior to Hardware Assembly

SAE AMS3281E-2010 360F(182C)间歇性使用的低密度整体油箱和燃料电池腔聚硫(t)合成橡胶密封剂

This specification covers three types and three classes of fuel-resistant polysulfide (T) sealing compound with low specific gravity, supplied as a two-component system which cures at room temperature. This sealing compound has been used typically in sealing aircraft integral fuel tanks, fuel tank fillets and faying surfaces, pressure barriers and moldline surfaces, but usage is not limited to such applications. The sealing compound is resistant to jet fuels and is capable of withstanding long-term exposure from -65 to +250 °F (-54 to +121 °C) and short-term exposure (6 hours) to 360 °F (182 °C).

Sealing Compound, Polysulfide (T) Synthetic Rubber for Integral Fuel Tank and Fuel Cell Cavities Low Density for Intermittent Use to 360 °F (182 °C)

DIN EN 2434-003:2010 航空航天系列.涂料和清漆.双组分冷固化聚亚安脂光洁度.第3部分:针对内部灵活的和强耐液体性;德文版本和英文版本EN 2434-002-2010

Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Part 003: Flexible and high fluid resistance for interior; German and English version EN 2434-003:2010

DIN EN 2434-001:2010 航空航天系列.涂料和清漆.双组分冷固化聚氨酯光洁度.第001部分:基本要求;德文和英文版本EN 2434-004-2010

Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Part 001: Basic requirements; German and English version EN 2434-001:2010

BS EN 2434-001:2010 航空航天系列.涂料和清漆.双组分冷固化聚氨酯光洁度.基本要求

This European Standard specifies the basic requirements for a two component polyurethane finish, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications. The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435-002. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.

Aerospace series. Paints and varnishes. Two component cold curing polyurethane finish. Basic requirements

SAE AMS3678/13-2010 13类10%聚酰亚胺填充童式聚四氟乙烯(PTFE)模型或者半成品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 10% polyimide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.

Type 13 10% Polyimide Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/7A-2010 7类童式聚四氟乙烯(PTFE)模型或者半成品含有25%的碳纤维和石墨

This specification covers a polytetrafluoroethylene (PTFE) resin filled with carbon and graphite in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for parts such as backup rings and seal elements in both static and dynamic applications requiring dimensional stability up to 450 °F (232 °C) with good mechanical properties, but usage is not limited to such applications. Each application should be considered individually.

Type 7 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 25% Carbon and Graphite

BS EN 2434-002:2010 航空航天系列.涂料和清漆.双组分冷固化聚氨酯光洁度.强耐化学试剂性

This European Standard specifies the requirements for a two component polyurethane finish to be applied over a primer for interior and exterior aerospace applications, where maximum resistance to normal operational fluids is required. The properties specified in this European Standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435-002. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.

Aerospace series. Paints and varnishes. Two component cold curing polyurethane finish. High chemical resistance

SAE AMS3678/10A-2010 10类童式聚四氟乙烯(PTFE)模型或者半成品含有15%的碳纤维

This specification covers a polytetrafluoroethylene (PTFE) resin filled with carbon fiber in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for parts such as backup rings and seal elements in both static and dynamic applications requiring dimensional stability up to 450 °F (232 °C) with good mechanical properties, but usage is not limited to such applications. Each application should be considered individually.

Type 10 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 15% Carbon Fiber

SAE AMS3678/4A-2010 4型,25%玻璃填充原聚四氟乙烯(PTFE)模制品或挤压制品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 25% glass fiber in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for dynamic seal components requiring dimensional stability up to 450 °F (232 °C), but usage is not limited to such applications. Each application should be considered individually.

Type 4 25% Glass Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/5A-2010 类型5的聚四氟乙烯(PTFE)着色模型或挤压件

This specification covers a polytetrafluoroethylene (PTFE) resin filledwith inorganic pigment in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for parts such as backup rings and seal elements in both static and dynamic applications requiring dimensional stability up to 450 °F (232 °C) with good mechanical properties, but usage is not limited to such applications. Each application should be considered individually.

Type 5 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with Pigment

SAE AMS3678/6A-2010 6型,60%青铜填充原聚四氟乙烯(PTFE)模制品或挤压制品

This specification covers a polytetralfuoroethylene (PTFE) resin filled with 60% bronze powder in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically bearing and wear ring applications in a lubricated environment against steel, stainless steels, and chromium plate, and requiring dimensional stability up to 450 °F (232 °C), but usage is not limited to such applications. Each application should be considered individually.

Type 6 60% Bronze Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/1B-2010 1型,原聚四氟乙烯(PTFE)模制品和挤压制品

This specification covers an unfilled grade of virgin polytetrafluoroethylene (PTFE) resin in the form of extruded or molded rods or tubes which are sintered after molding, or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for parts such as backup rings and seal component for static and light duty applications requiring dimensional stability up to 450 °F (232 °C) with good mechanical properties, but usage is not limited to such applications. Each application should be considered individually.

Type 1 Virgin Polytetrafluoroethylene (PTFE) Moldings and Extrusions

BS EN 2434-003:2010 航空航天系列.涂料和清漆.双组分冷固化聚氨酯光洁度.内部柔韧性和高流动阻性

This European Standard specifies the requirements for a two component polyurethane finish, in a limited range of colours, to be applied over a primer for interior aerospace applications, offering flexibility and high resistance to fluid attack. The properties specified in this European Standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 and EN 23270 and painted with primer to EN 2435-003. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.

Aerospace series. Paints and varnishes. Two component cold curing polyurethane finish. Flexible and high fluid resistance for interior

SAE AMS3678/9B-2010 9类童式聚四氟乙烯(PTFE)成型品颜料,AS4716和AS5857备份环

This specification covers a polytetrafluoroethylene (PTFE) resin filled with inorganic pigment in the form of extruded or molded rods or tubes which are sintered after molding. The blue colored material is designated for use in rod glands only and the yellow colored material is designated for use in piston glands only. The brown colored material is designated for use in AS5857 rod glands only and the green colored material is designated for use in AS5857 piston glands only. These products have been used as backup rings in AS4716 Glands for both static and dynamic applications and in AS5857 Glands for static stability up to 450 °F (232 °C) with good mechanical properties is required, but usage is need not be limited to such applications. Each application should be considered individually.

Type 9, Virgin Polytetrafluoroethylene (PTFE) Moldings with Pigment for AS4716 and AS5857 Backup Rings

SAE AMS3678/12-2010 12类10%的矿物,2.5%二硫化钼填充处女聚四氟乙烯(PTFE)模型或半成品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 10% mineral and 2.5% molybdenum disulfide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.

Type 12, 10% Mineral, 2.5% Molybdenum Disulfide Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/8A-2010 含有10%碳纤维的类型8聚四氟乙烯(PTFE)模型或挤压件

This specification covers a polytetrafluoroethylene (PTFE) resin filled with carbon fiber in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for parts such as backup rings and seal elements in both static and dynamic applications requiring dimensional stability up to 450 °F (232 °C) with good mechanical properties, but usage is not limited to such applications. Each application should be considered individually.

Type 8, Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 10% Carbon Fiber

SAE AMS3678/2A-2010 2型,15%石墨填充原聚四氟乙烯(PTFE)模制品或挤压制品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% graphite in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for seal components for dynamic reciprocating and rotary applications requiring dimensional stability up to 450 °F (232 °C) with good mechanical properties, but usage is not limited to such applications. Each application should be considered individually.

Type 2, 15% Graphite Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/3A-2010 3型,15%玻璃,5%二硫化钼填充原聚四氟乙烯(PTFE)模制品或挤压制品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% glass fiber and 5% molybdenum disulfide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for seal components requiring high temperature and pressure resistance and dimensional stability up to 450 °F (232 °C) with good wear resistance, but usage is not limited to such applications. Each application should be considered individually.

Type 3, 15% Glass, 5% Molybdenum Disulfide Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions