V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3678/1B-2010 1型,原聚四氟乙烯(PTFE)模制品和挤压制品

This specification covers an unfilled grade of virgin polytetrafluoroethylene (PTFE) resin in the form of extruded or molded rods or tubes which are sintered after molding, or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for parts such as backup rings and seal component for static and light duty applications requiring dimensional stability up to 450 °F (232 °C) with good mechanical properties, but usage is not limited to such applications. Each application should be considered individually.

Type 1 Virgin Polytetrafluoroethylene (PTFE) Moldings and Extrusions

SAE AMS3678/4A-2010 4型,25%玻璃填充原聚四氟乙烯(PTFE)模制品或挤压制品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 25% glass fiber in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically for dynamic seal components requiring dimensional stability up to 450 °F (232 °C), but usage is not limited to such applications. Each application should be considered individually.

Type 4 25% Glass Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/13-2010 13类10%聚酰亚胺填充童式聚四氟乙烯(PTFE)模型或者半成品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 10% polyimide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.

Type 13 10% Polyimide Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/6A-2010 6型,60%青铜填充原聚四氟乙烯(PTFE)模制品或挤压制品

This specification covers a polytetralfuoroethylene (PTFE) resin filled with 60% bronze powder in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process. These products have been used typically bearing and wear ring applications in a lubricated environment against steel, stainless steels, and chromium plate, and requiring dimensional stability up to 450 °F (232 °C), but usage is not limited to such applications. Each application should be considered individually.

Type 6 60% Bronze Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3678/15-2010 15类,15%聚酰亚胺填充童式聚四氟乙烯(PTFE)模型或者半成品

This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% aromatic polymer in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.

Type 15, 15% Aromatic Polymer Filled Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions

SAE AMS3619D-2010 耐高温315℃(599℉)层压聚酰亚胺树脂

This specification covers a single-component, heat-reactive, thermosetting aromatic system which thermally cures to form a polyimide polymer structure. This product has been used typically as a resin matrix for fiber-reinforced- composite parts requiring good strength after long-term exposure up to 315 °C (599 °F) and after short-term exposure up to 370 °C (698 °F), but usage is not limited to such applications.

Resin, Polyimide, Laminating High Temperature Resistant, 315 °C (599 °F)

SAE AMS3613D-2010 薄膜,覆铜箔聚酯

This specification covers a polyester resin in the form of a film clad on one or both sides with copper foil. This product has been used typically as a base material for fabrication of flexible printed wiring for electronic circuit applications operating in the range -65 and +105 °C (-85 and +221 °F), but usage is not limited to such applications.

Film, Copper Clad Polyester

BS 3F 128:2010 航空用棉带规范(额定经纱为R310 tex)

This British Standard specifies requirements for the yarn, manufacture, finish, construction and identification of cotton webbings for aerospace purposes.

Specification for cotton webbing suitable for aerospace purposes (warp yarn nominally R 310 tex)

SAE AMS3612C-2010 通用电气级聚酯薄膜

This specification covers a polyester resin in the form of film and film tape. This film has been used typically for parts requiring electrical insulating properties from -60 to +150 °C (-76 to +302 °F), but usage is not limited to such applications.

Polyester Film Electrical Grade, General Purpose

DIN 65046-3:2010 航空航天.表面保护涂层的试验方法.油漆和清漆.第3部分:按交货条件进行的试验

Aerospace - Methods of test for surface protective coatings; Paints and varnishes - Part 3: Tests in as-delivered condition

DIN 65046-2:2010 航空航天.表面保护涂层的试验方法.油漆和清漆.第2部分:试样,试样的制备,干燥

Aerospace - Methods of test for surface protective coatings; Paints and varnishes - Part 2: Specimens, preparation of specimens, drying

DIN 65046-4:2010 航空航天.表面保护涂层的试验方法.油漆和清漆.第4部分:涂层试验

Aerospace - Methods of test for surface protective coatings; Paints and varnishes - Part 4: Testing of coatings

DIN 65046-5:2010 航空航天.表面保护涂层的试验方法.油漆和清漆.第5部分:涂层阻力试验

Aerospace - Methods of test for surface protective coatings; Paints and varnishes - Part 5: Coating resistance tests

SAE AMS-S-83474A-2010 加填树脂复合物和片状预浸材料的模塑垫片

This specification covers the requirements for filled, resinous thermosetting compound and sheet prepreg to fabricate shims for use during assembly of aircraft components and parts.

Shims, Molded, Filled Resin Compound and Sheet Prepeg

SAE AMS3277E-2010 聚硫醚橡胶,快速固化整体燃料箱密封剂和一般要求,间歇性使用360℉(182℃)

This specification covers polythioether rubber fuel resistant sealing compounds supplied as a two component system which cures at room temperature. This product has been used in aircraft integral fuel tanks for repair of fillet and fastener seals and faying surface seals as well as initial sealing of faying surfaces, overcoating of fasteners, and sealing of seams and joints, for service from -80 to +320°F (-62 to +160°C), with short-term recurring exposures (approximately six hours) up to 360°F (182°C), but usage is not limited to such applications. This product is not recommended for use on aircraft windshields or canopies or other applications where crazing or degradation of plastic components may occur. Sealing compound must be applied at temperatures above 50°F (10°C), but will cure at lower temperatures.

Sealing Compound, Polythioether Rubber, Fast Curing Integral Fuel Tanks and General Purpose, Intermittent Use to 360°F (182°C)

ISO 15856:2010 航空航天系统.空间环境.非金属材料辐射照射用仿真导则

Space systems - Space environment - Simulation guidelines for radiation exposure of non-metallic materials

BS EN 4115:2010 航空航天系列.夹紧用橡胶垫.尺寸规格,质量

This standard specifies the required characteristics for rubber cushions used on clamps according to EN 3730, EN 4113, EN 4114. For temperature range and environmental conditions see Table 1.

Aerospace series - Cushion, rubber for clamps - Dimensions, masses

SAE AMS3656G-2010 标准强度烧结聚四氟乙烯(PTFE)挤压制品

This specification covers a virgin, unfilled polytetrafluoroethylene (PTFE) in the form of extruded and sintered rods, tubes, and profiles. These products have been used typically for parts, such as insulators and bushings requiring chemical inertness up to 500 °F (260 °C), but usage is not limited to such applications. For such applications such as bearing, seals, and back-up rings that do not require dielectric properties and radiographic inspection it is recommended to us AMS 3678/1 Grade B.

Polytetrafluoroethylene (PTFE) Extrusions, Normal Strength, As Sintered

SAE AMS3337E-2010 耐超低温的硅酮(PVMQ)橡胶.65-75

This specification covers a silicone (PVMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for parts required to operate or seal from -121 to +446 °F (-85 to +230 °C) compounded especially for operation at extreme low temperatures. Silicone rubber is resistant to deterioration by weathering and by high-aniline-point petroleum-base oils and remains flexible over the temperature range noted. These products are not normally suitable for use in contact with low-aniline-point petroleum-base fluids, including fuels, due to excessive swelling.

Silicone (PVMQ) Rubber Extreme-Low-Temperature Resistant 65 - 75

SAE AMS3657E-2010 优质强度、As烧结的聚四氟乙烯(PTFE)挤压制品

This specification covers one grade of polytetrafluoroethylene (PTFE) in the form of extruded and sintered rods, tubes, and profiles. These products have been used typically for parts, such as bushings and insulators, requiring chemical inertness up to 500 °F (260 °C) and better mechanical and/or electrical properties than AMS 3656, but usage is not limited to such applications. When improved dimensional stability is required, it is recommended that stress relieved product in accordance with AMS 3659 be specified. For parts such as seals, back-up rings and bearings that do not require dielectric properties and radiographic inspection it is recommended to use AMS 3678/1 Grade B.

Polytetrafluoroethylene (PTFE) Extrusions, Premium Strength, As Sintered