V13 航空与航天用非金属材料 标准查询与下载

SAE AMS3041E-2008 即用型以油为媒介物的非荧光磁性粒子用湿方法

This specification covers nonfluorescent magnetic particles in the form of a mixed, ready-to-use suspension in an odorless inspection oil vehicle. These products have been used typically as the inspection medium in a wet magnetic particle inspection system in accordance with ASTM E 1444, but usage is not limited to such application.

Magnetic Particles, Nonfluorescent, Wet Method, Oil Vehicle, Ready-to-Use

SAE AMS3040D-2008 非荧光磁性粒子用干法

This specification covers nonfluorescent, magnetic particles having black, red, gray, or other color, as specified, supplied in the form of dry powders. This product is used typically as an inspection medium in a dry magnetic particle inspection process in accordance with ASTM E 1444, but usage is not limited to such application.

Magnetic Particles, Nonfluorescent, Dry Method

SAE AMS3045E-2008 即用型以油为媒介物的荧光磁性粒子用湿法

The specification fluorescent magnetic particles in the form of a mixed, ready-to-use suspension in an odorless inspection oil vehicle. These particles have been used typically as the inspection medium in a wet method, magnetic inspection system as defined in ASTM E 1444, but usage is not limited to such application.

Magnetic Particles, Fluorescent, Wet Method, Oil Vehicle Ready-to-Use

SAE AS9956A-2008 AMS 3668 预成型(聚四氟乙烯)密封填料

Packing, Preformed (PTFE) AMS 3668, Seal

DIN EN 4170:2008 航空航天系列.涂料和清漆.防冷裂缝温度循环测量的试验方法

This standard describes a procedure of ageing to assess the resistance of a coated panel (metallic or organic substrate) to a temperature cycle (cold, hot, hot and wet) for aerospace purposes. This test deals with the assessment of the capability of the paint to support modification of internal stresses without any crack formation, peeling or other defects due to modification of the mechanical properties of the paint system.

Aerospace series - Paints and varnishes - Test method for measurement of resistance to cold crack temperature cycle; German and English version EN 4170:2007

SAE AMS7379-2008 橡胶:航空器发动机油,燃料和液压系统中弹性密封物用硬度为70～80,低温密封Tg -40℉(-40℃)的碳氟化合物人造橡胶(FKM)

1.1 FormThis specification covers high temperature, compression set and fluid resistant fluorocarbon elastomer material to beused in the form of O-rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospaceapplications.1.2 ApplicationThese products have resistance to a variety of gas turbine engine oils, including high thermal stability (HTS) oils, fuels,and hydraulic fluids, but usage is not limited to such applications. Each application should be considered separately. Thisfluorocarbon (FKM) has a service temperature range of -60 to +400 °F (-51 to +204 °C) in air.1.3 Safety - Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in this specification may involve theuse of hazardous materials, this specification does not address the hazards, which may be involved in such use. It is thesole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to takenecessary precautionary measures to ensure the health and safety of all personnel involved.

Rubber: Fluorocarbon Elastomer (FKM) 70 to 80 Hardness, Low Temperature Sealing Tg -40 °F (-40 °C) for Elastomeric Seals in Aircraft Engine Oil, Fuel and Hydraulics Systems

SAE AMS3214L-2008 35-45耐芳族燃料的丁腈(NBR)橡胶

1.1 FormThis specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.1.2 ApplicationThese products have been used typically for parts, such as gaskets, diaphragms, bushings, grommets, and sleeves,requiring resistance to aromatic and aliphatic fuels when continuously or alternately exposed to both, but usage is not limited to such applications.1.3 Safety - Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is thesole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved.

Acrylonitrile Butadiene (NBR) Rubber, Aromatic Fuel Resistant, 35-45

SAE AMS3200K-2008 55-65耐石油基液压液的丁晴(NBR)橡胶

1.1 FormThis specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.1.2 ApplicationThese products have been typically used as seals and gaskets, in contact with petroleum-base hydraulic fluids but usage is not limited to such applications. Each application should be considered individually.1.3 Safety - Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is thesole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved.

Butadiene Acrylonitride (NBR) Rubber, Petroleum-Base Hydraulic Fluid Resistant, 55-65

SAE AMS2950/1-2008 核心维修用粘合剂.第1部分:一般要求

This Technical Specification gives information about technical requirements and qualification procedures of adhesivepaste with or without thickening agent for core restoration of aircraft components.

Paste Adhesive for Core Restoration Part 1- General Requirements

SAE AMS3756B-2008 烧结的25玻璃、75%聚四氟乙烯(PTFE)树脂、玻璃纤维填充的聚四氟乙烯模塑制品

1.1 FormThis specification covers one grade of glass-fiber-filled polytetrafluoroethylene (PTFE) in the form of molded billets.1.2 ApplicationPrimarily for parts, such as seals and back-up rings, requiring chemical inertness and superior mechanical properties upto 500 °F (260 °C).1.3 Safety - Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in this specification may involve theuse of hazardous materials, this specification does not address the hazards which may be involved in such use. It is thesole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to takenecessary precautionary measures to ensure the health and safety of all personnel involved.

Moldings, Glass Fiber Filled Polytetrafluoroethylene, 75% PTFE Resin, 25 Glass, As Sintered

SAE AMS3239F-2008 85-95耐磷酸盐树脂的丁基(IIR)橡胶

1.1 FormThis specification covers a butyl (IIR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.1.2 ApplicationThese products have been used typically for parts such as V-rings, gaskets, grommets, and seals requiring resistance to phosphate esters or low permeability to gases, but usage is not limited to such applications. These products are notsuitable for use in contact with petroleum-base fluids due to excessive swell.1.3 Safety - Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is thesole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved.

Butyl (IIR) Rubber, Phosphate Ester Resistant, 85-95

SAE AMS3238F-2008 65-75的耐磷酸盐树脂的丁基(IIR)橡胶

1.1 FormThis specification covers a butyl (IIR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.1.2 ApplicationThis product has been used typically for parts, such as O-rings, gaskets, grommets, and seals, requiring resistance to phosphate esters or low permeability to gases, but usage is not limited to such applications. Not suitable for use in contact with petroleum-base fluids due to excessive swell.1.3 Safety - Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is thesole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved.

Butyl (IIR) Rubber, Phosphate Ester Resistant, 65-75

SAE AMS3222H-2008 高膨胀为45-55的合成橡胶热油抵抗力

1.1 FormThis specification covers a synthetic rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.1.2 ApplicationThis product has been typically used for gasket-type seals in contact with hot, petroleum-based lubricating oils where a space-filling seal operating from -40 to +212 °F (-40 to +100 °C) is required, but usage is not limited to such applications.1.3 Safety Hazardous MaterialsWhile the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is thesole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved.

Synthetic Rubber Hot Oil Resistant, High Swell 45-55

BS EN 3717:2008 航空航天系列.管.发动机防冻液系统的选择

The present standard gives a selection of external diameters and thicknesses of tubes according to ISO 2964. These tubes shall be used for conveying fluids such as kerosene, oil, air, etc. for engine application.

Aerospace series - Tubes - Selection for engines fluid systems

GJB 1251A-2008 浇铸航空有机玻璃规范

本规范规定了浇铸航空有机玻璃的要求、质量保证规定和交货准备等。 本规范适用于由增塑和未增塑的甲基丙烯酸甲酯的均聚物、甲基丙烯酸甲酯与甲基丙烯酸的共聚物制备的浇铸航空有机玻璃。

Specification for cast acrylic plastic sheet of aircraft

GJB 6466-2008 导弹用热压多晶氟化镁平板规范

本规范规定了导弹用热压多晶氟化镁平板产品技术要求、质量保证规定和交货准备等。 本规范适用于热压法生产的直径不大于270mm的多晶氟化镁平板（毛坯）产品。

Specification for hot-pressed polycrystalline magnesium fluoride plate for missiles

SAE AMS3276E-2008 断续使用至360℉(182℃)的整体油箱和一般用途用密封化合物

This specification covers five classes of a fuel-resistant polysulfide (T) sealing compound supplied as a two-component system. This sealing compound has been used typically for fuel tank sealing, cabin pressure sealing, and aerodynamic smoothing, but usage is not limited to such applications. It can be used for faying surface sealing, for wet-installation of fasteners, for overcoating fasteners, sealing joints and seams, and nonstructural adhesive bonding. This room-temperature curing sealing compound can be used in fuel areas as well as nonfuel areas. Curing of this material can be accelerated at higher temperatures. This material is usable from -65 to 250 ?F (-54 to 121 ?C), with short-term exposure (approximately six hours) to 360 ?F (182 ?C).

Sealing Compound, Integral Fuel Tanks and General Purpose, Intermittent Use to 360 °F (182 °C)

SAE AMS1528D-2008 飞行器外表面用压力喷洒式乳状清洁剂

This specification covers an emulsion-type, low-foaming cleaner in the form of a liquid. This cleaner has been used typically for removing soils from painted and unpainted exterior surfaces of aircraft by pressure spray or manual applications, but usage is not limited to such applications.

Cleaner for Aircraft Exterior Surfaces, Emulsion, Pressure-Spray Type

SAE AMS1551A-2008 涡轮发动机气路用含水型清洁剂

This specification covers a solvent-free cleaner in the form of an aqueous-base liquid concentrate or a ready-to-use liquid. This cleaner has been used typically for cleaning installed turbine engines by spraying diluted cleaner or ready-to-use cleaner into the intake during a starter crank operation or on-line engine cleaning in accordance with the engine manufacturer's procedure, but usage is not limited to such applications.

Cleaner, Turbine Engine Gas Path Aqueous Type

SAE AMS1523B-2008 飞行器外表面用水基凝胶清洁剂

This specification covers a thickened, water-base, type cleaner in the form of a gel. This cleaner has been used typically for removing soils from exterior surfaces of aircraft, such as landing gears, wheel wells, and flap cavities but usage is not limited to such applications.

Cleaner for Exterior Aircraft Surfaces Thickened or Gel-Type, Water-Base