V18 冷加工工艺 标准查询与下载

SAE AMS2483C-2010 涂铝修整方案用涂黑处理方法

This specification covers a blackening solution, applied at room temperature, to damaged or reworked surfaces of black-dyed anodized (AMS 2472) aluminum to proved a uniform ebony-black surface. This solution has been used typically for touch-up of dyed anodic coatings used for decorative and optical applications, but usage is not limited to such applications.

Blackening Solution for Aluminum Touch-Up Solution

NF L06-823:2010 航空航天系列.喷丸介质.玻璃珠

Aerospace series - Blast media - Glass beads.

NF L06-825:2010 航空航天系列.喷砂介质.砂粒铸钢砂

Aerospace series - Blast media - Grit cast steel shot.

NF L06-826:2010 航空航天系列.喷砂介质.圆铸钢砂

Aerospace series - Blast media - Round cast steel shot.

SAE AMS2481J-2010 耐磨损磷化处理

This specification covers the requirements for a manganese phophate coating on ferrous alloys. This process has been used typically to produce a coating that will minimize chafing of contacting steel surfaces and retain an oil film, but usage is not limited to such applications.

Phosphate Treatment Antichafing

SAE AMS2430R-2010 自动喷丸

This specification covers the engineering requirements for automatic peening surfaces of parts by impingement of metallic shot, glass beads, and ceramic shot. To induce residual compressive stress in surface layers of parts, thereby increasing fatigue strength and resistance to stress corrosion cracking but usage is not limited to such applications.

Shot Peening, Automatic

SAE AMS-QQ-P-416C-2009 镀镉(电沉积)

This specification covers the requirements for electrodeposited cadmium plating.

Plating, Cadmium (Electrodeposited)

SAE AMS-QQ-N-290B-2009 镀镍(电镀)

AMS-QQ-N-290B has been reinstated to cover previously qualified products. New design applications are encouraged to consider AMS2403 and AMS2423. These products have been used typically for electrodeposited nickel plating on steel, copper and copper alloys, and zinc and zinc alloys, but usage is not limited to such applications. The original issue of this document was taken directly from U.S. Military Specification QQ-N-290A and contained only minor editorial and format changes required to bring it into conformance with the publishing requirements of SAE technical standards. The initial release of AMS-QQ-N-290 is intended to replace QQ-N-290A. Any part numbers established by the original specification remain unchanged. The original Military Specification was adopted as an SAE standard under the provisions of the SAE Technical Standards Board (TSB) Rules and Regulations (TSB 001) pertaining to accelerated adoption of government specifications and standards. TSB rules provide for (a) the publication of portions of unrevised government specifications and standards without consensus voting at the SAE Committee level, and (b) the use of the existing government specification or standard format. Under Department of Defense policies and procedures, any qualification requirements and associated qualified products lists are mandatory for DOD contracts. Any requirement relating to qualified products lists (QPL's) has not been adopted by SAE and is not part of this SAE technical document.

Nickel Plating (Electrodeposited)

NF L06-833:2009 航空航天系列.金属部件用压缩表面应力诱因的超声喷丸硬化法

Aerospace series - Ultrasonic shot peening for inducement of compressive surface stresses for metallic parts.

MH/T 3017-2008 民用航空金属零件旋片喷丸强化工艺

本标准规定了民用航空金属零件的表面较小区域内(包括孔)及现场局部的旋片喷丸强化工艺中旋片喷丸的(以下简称喷丸)强度符号、材料和工具、工艺参数的确定、步骤和操作要求、质量控制及喷丸后零件的处理等技术要求。 本标准适用于在交变应力和应力腐蚀条件下工作的民用航空金属(含结构钢、不锈钢、铸铁、铝合金、镁合金、铜合金、钛合金以及铁、镍基高温合金等)零件及部件的喷丸强化处理。

The flap peening of metal parts of civil aviation

SAE AMS2408J-2008 镀锡

This specification covers the requirements for electrodeposition of tin on metals and the properties of the deposit. This process has been used typically to prevent galling or seizing of metal surfaces, to provide a surface for soft soldering, or to improve corrosion resistance, but usage is not limited to such applications.

Plating, Tin

SAE AMS2415J-2008 铅和铟涂层

This specification covers the requirements for electrodeposited and diffused lead and indium plate. This process has been used typically to improve the performance and prevent corrosion of bearings or of other parts, but usage is not limited to such applications.

Plating, Lead and Indium

SAE AMS2411G-2008 高温设施用镀银工艺

This specification covers the engineering requirements for silver deposited on metal parts with a nickel strike between the basis metal and the silver deposit. This process has been used typically to prevent galling or seizing of surfaces of parts, such as fasteners, made of low-alloy steel, corrosion and heat resistant steel, and nickel alloys for use up to 1400 ?F (760 ?C).

Plating, Silver for High Temperature Applications

SAE AMS2438C-2007 硬致密沉积物镀薄铬层

This specification covers the engineering requirements thin, hard, dense chromium plating on surfaces of ferrous and nonferrous alloys. This plating has been used typically to provide improved lubricity, wear and/or corrosion resistance to selected materials but usage is not limited to such applications.

Plating, Chromium Thin, Hard, Dense Deposit

SAE AMS2432C-2007 计算机检测的喷丸处理

This specification establishes the engineering requirements for computer monitored peening of parts surfaces. This procedure is used typically to provide a means by which the shot peening process can be performed repeatedly on parts in order to satisfy material component design requirements, but usage is not limited to such applications. Shot peening locations used for intensity verification (Almen test strip locations), media type, media size and peening intensities shall be as specified by the cognizant engineering organization. When any of these parameters are not specified, they shall be established in accordance with 3.2.8 of this specification and listed as process control parameters in accordance with 3.7. Processes, such as tumble peening, slurry peening, peen forming and straightening, peening for prevention of intergranular corrosion, and peening to produce a surface texture, are recognized but their requirements are not covered.

Shot Peening, Computer Monitored

SAE AMS2472F-2007 带着色涂层铝合金硫酸工艺的阳极处理

This specification establishes the for dyed anodic coatings on aluminum alloys. This process has been used typically to increase corrosion resistance and to produce colored surfaces on aluminum alloy parts, but usage is not limited to such applications. AMS 2470 or AMS 2471 should be specified for coatings to be used as a base for paint or other organic finishes. This process is not suitable for parts which contain joints or recesses in which the anodizing solution may be retained.

Anodic Treatment of Aluminum Alloys Sulfuric Acid Process, Dyed Coating

AECMA PREN 4528-2007 航空航天系列.钢FE-PA3903(X12CrNi18-10)冷轧条弹簧小于或等于3mm,1250 Mpa小于或等于Rm＜1640Mpa.P1版

This draft is now available for public comment and your views and technical comments on it would be appreciated. If you have no specific comments to make hut find it generally acceptable it would be helpful if you would notify US accordingly. Suggestions entailing revision of the text should indicate the preferred wording. Please quote the relevant clause number against any comment.

Aerospace Series Steel FE-PA3903 (X12CrNi18-10) Cold Rolled Strip for Springs a Less Than or Equal to 3 mm 1 250 MPa Less Than or Equal to Rm Less Than 1 640 MPa Edition P1

SAE AMS2759/8A-2007 离子氮化

This specification establishes the requirements and procedures for producing a hard, wear resistant ion nitrided surface on steel parts. The nitriding process, described herein, is applicable to alloy steels, tool steels, nitriding steels, corrosion resistant steels, and other ferrous alloys.

(R) Ion Nitriding [Superseded: SAE AMS-S-6090B, SAE AMS-S-6090A, SAE AMS-S-6090]

SAE AS4194A-2007 薄板材和带材的表面抛光术语

This SAE Aerospace Standard (AS) defines the nomenclature for surface finishes commonly used for sheet and strip in aerospace material specifications. It is applicable to steel and to iron, nickel, cobalt, and titanium base alloys.

Sheet and Strip Surface Finish Nomenclature

SAE AMS2451/10A-2007 锡锌低氢脆化用电镀刷

This specification covers the engineering requirements and processes for brush plating of tin-zinc by electrodeposition. This process has been used typically to improve corrosion resistance of steel parts, to repair tin-zinc deposits and to repair damaged or worn parts, but usage is not limited to such applications.

Plating, Brush, Tin-Zinc Low Hydrogen Embrittlement