共找到 2302 条与 管件、卡箍、密封件 相关的标准,共 154 页
HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARELESS, STRAIGHT TO 45
HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARELESS, STRAIGHT TO 45
HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARELESS, 45 DEGREES TO 90 DEGREES
HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARELESS, 45 DEGREES TO 90 DEGREES
Fitting Assembly, Tee, Beam Seal, Retained Nut on Side
Fitting, Tee, Beam Seal Bulkhead on Side
The purpose of this report is to provide guidelines for specifying O-rings that would be considered suitable for testing when writing O-ring material specifications. There are many tests that have been developed to characterize rubber O-rings. Many of these tests are independent of the size of the O-ring being tested. However, there are some tests, specifically, stress/strain properties, that are a function of the O-rings size. The purpose of this report is to provide guidelines for specifying O-rings that would be considered suitable for testing when writing O-ring material specifications.
Suitable Test Sizes for O-ring Specifications
This SAE Standard (AS) defines the requirements for a convoluted polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in aircraft fluid systems at temperatures of -65 to 400 degrees F and at operating pressures per Table 1.
Hose Assemblies, Convoluted Polytetrafluoroethylene Metallic Reinforced, High Temperature, Medium Pressure, Aircraft
GASKET - 37?FLARED TUBE FITTING, NICKEL, AMS 5553
GASKET - 37?FLARED TUBE FITTING, NICKEL, AMS 5553
Fitting, Elbow, 90°, External Thread, Beam Seal to Integral Weld Ring
This standard specifies the required characteristics and test applicable to sealing sleeves used in elements of connection according to EN 3155-002 and EN 4530-002.
Aerospace series - Sealing sleeves used in elements of connection - Part 005: Sealing sleeves for external diameter cable 3 mm to 4,1 mm - Product standard
This International Standard specifies requirements for lightweight polytetrafluoroethylene (PTFE) hose assemblies for use in aircraft hydraulic systems at temperatures between − 55 °C and 204 °C (− 65 °F and 400 °F), and at a nominal pressure up to 3 000 psi (20 684 kPa) or 21 000 kPa (3 046 psi). The hose assemblies are also suitable for use within the same temperature and pressure limitations in aircraft pneumatic systems where some gaseous diffusion through the wall on the PTFE liner may be tolerated. The use of these hose assemblies in high-pressure pneumatic storage systems is not recommended. In addition, installations in which the limits specified in this International Standard are exceeded, or in which the application is not covered specifically by this International Standard, for example for oxygen, are subject to the approval of the purchaser. Annex A is a listing of hose assembly procurement standards conforming to this International Standard.
Aerospace. Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 400
This standard specifies the required characteristics and test applicable to sealing sleeves used in elements of connection according to EN 3155-002 and EN 4530-002.
Aerospace series - Sealing sleeves used in elements of connection - Part 006: Sealing sleeves for external diameter cable 4,68 mm to 5,05 mm - Product standard
FITTING, NIPPLE, FLARED TUBE TO PIPE THREAD, FOR SEAL RING FSC 4730
Nipple - Flared Tube to Pipe Thread, for Seal Ring
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
Fittings, Tube, Fluid Systems, Separable, Beam Seal, 3000/4000 psi, General Specification For (Supplement 1)
This standard specifies the characteristics and technical requirements of tubular sleeves for shear screws with flush head, which may be plain or provided with a series of annular grooves, in corrosion resisting steel, passivated, with a 0,50 mm wall thickness, for maximum operating temperature 650 ? for aerospace applications.
Aerospace series - Sleeves, tubular, for shear screws with flush head, in corrosion resisting steel, passivated, (0,50 mm wall thickness); German and English version EN 4307:2005
This standard specifies the characteristics and technical requirements of tubular sleeves for shear screws with flush head, which may be plain or provided with a series of annular grooves, in corrosion resisting steel, passivated, with a 0,25 mm wall thickness, for maximum operating temperature 650 ? for aerospace applications.
Aerospace series - Sleeves, tubular, for shear screws with flush head, in corrosion resisting steel, passivated, (0,25 mm wall thickness); German and English version EN 4304:2005
This standard specifies the characteristics and technical requirements of tubular sleeves for tension screws with flush head, which may be plain or provided with a series of annular grooves, in corrosion resisting steel, passivated, with a 0,50 mm wall thickness, for maximum operating temperature 650 ? for aerospace applications.
Aerospace series - Sleeves, tubular, for tension screws with flush head, in corrosion resisting steel, passivated, (0,50 mm wall thickness); German and English version EN 4306:2005
FITTING, ELBOW, 45? BEAM SEAL BULKHEAD
FITTING, ELBOW, 45? BEAM SEAL BULKHEAD
This SAE Aerospace Standard (AS) covers medium-pressure, high-temperature, flexible, metal-hose assemblies suitable for operation in pneumatic systems up to 800 °F with excursion to 1200 °F for Class "B" and "N" and primarily for use on jet aircraft power plants.
(R) Hose Assemblies, Metal, Medium Pressure, High Temperature
FITTING END, BULKHEAD, SPHERICAL, 37?FLARED TUBE CONNECTION DESIGN STANDARDFIGURE 1 - FITTING END, STYLE GFIGURE 2 - FITTING END, STYLE HSAME AS STYLE G EXCEPT AS SHOWNTABLE 1A - DIMENSIONS A-K, INCH -POUND UNITS (IN)TABLE 1B - DIMENSIONS L-Z, INCH -POUND UNITS (IN)TABLE 1A - DIMENSIONS A-K, SI UNITS (MM)TABLE 1B - DIMENSIONS L-Z, SI UNITS (MM)
FITTING END, BULKHEAD, SPHERICAL, 37?FLARED TUBE CONNECTION DESIGN STANDARD
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号