V22 机械配件、构件 标准查询与下载



共找到 2047 条与 机械配件、构件 相关的标准,共 137

This standard specifies the characteristics of rigid single row ball bearings in steel, with cadmium-plated flanged alignment housing designed to withstand only slow rotations and oscillations under load. They are intended for use in the hubs of torsion lever and in separated supports for airframe/aerospace applications. The airframe rolling bearings defined in this standard may be used in the temperature range from - 54 ℃ to 150 ℃. However, being lubricated with the following greases (see EN 3727): -- ester type very high pressure grease (code letter A), operating range from - 73 ℃ to 121 ℃ or, -- synthetic hydrocarbons type very high pressure grease general purpose (code letter B) operating range from - 54 ℃ to 177 ℃. Their field of application when lubricated with code letter A grease is limited to 121 ℃.

Aerospace series - Bearings, airframe rolling - Rigid single row ball bearings in steel with flanged alignment housing, cadmium plated - Dimensions and loads; German and English version EN 3059:2007

ICS
49.035
CCS
V22
发布
2008-02
实施

This manual was developed to provide basic information and recommend sources of additional information pertaining to metallic gear materials, their treatments, and other considerations related to the manufacture and use of gearing. The gearing application conditions, including allowable stresses, environment, component geometry, and component weight limitations, must be understood to select the proper gear material. Metallurgical aspects of gearing as related to rating (allowable contact stress number and allowable bending stress number) are not included, but are covered in AGMA rating standards.

Gear Materials, Heat Treatment and Processing Manual

ICS
CCS
V22
发布
2008-01-01
实施

BEARING, PLAIN, SELF-ALIGNING, SELF-LUBRICATING, LINED BORE, LOW SPEED, WIDE, CHAMFERED RACE, -65 TO +325 °F;TABLE 1 - DIMENSIONS AND STRENGTHS;TABLE 2 - OVERSIZE BEARING DIMENSIONS;TABLE 3 - INTERNAL CLEARANCE

Bearing, Plain, Self-Aligning, Self-Lubricating, Lined Bore, Low Speed, Wide, Chamfered Outer Ring, -65° to 325°F

ICS
49.035
CCS
V22
发布
2007-10-01
实施

BEARING, PLAIN, SELF-ALIGNING, SELF-LUBRICATING, LINED BORE, LOW SPEED, NARROW, GROOVED RACE, -65 TO +325 °F;TABLE 1 - DIMENSIONS AND STRENGTHS;TABLE 2 - OVERSIZE BEARING DIMENSIONS;TABLE 3 - INTERNAL CLEARANCE;

Bearing, Plain, Self-Aligning, Self-Lubricating, Lined Bore, Low Speed, Narrow, Grooved Outer Ring, -65° to 325°F

ICS
49.035
CCS
V22
发布
2007-10-01
实施

Aerospace series - Bearings, airframe rolling - Double row self-aligning ball bearings with flanged outer ring in corrosion resisting steel, reduced internal radial clearance - Dimensions and loads.

ICS
49.035
CCS
V22
发布
2007-10-01
实施
2007-10-12

This standard specifies the characteristics of rigid single row ball bearings in steel, cadmium-plated with cadmium plated flanged alignment housing designed to withstand only slow rotations and oscillations under load. They are intended for use in the hubs of torsion lever and in separated supports for airframe/aerospace applications. The airframe rolling bearings defined in this standard may be used in the temperature range from – 54 °C to 150 °C. However, being lubricated with the following greases (see EN 3727):  ester type very high pressure grease (code letter A), operating range from – 73 °C to 121 °C or,  synthetic hydrocarbons type very high pressure grease general purpose (code letter B) operating range from – 54 °C to 177 °C. Their field of application when lubricated with code letter A grease is limited to 121 °C.

Aerospace series - Bearings, airframe rolling - Rigid single row ball bearings in steel, cadmium plated, with flanged alignment housing, cadmium plated - Dimensions and loads

ICS
49.035
CCS
V22
发布
2007-07-31
实施
2007-07-31

This standard specifies the characteristics of rigid single row ball bearings in corrosion resisting steel with a solid or lightweight flanged alignment housing, designed to withstand only slow rotations and slight oscillations under load. They are intended for use in the hubs of torsion lever and in separated supports for airframe/aerospace applications. The airframe rolling bearings defined in this standard may be used in the temperature range from – 54 °C to 150 °C. However, being lubricated with the following greases (see EN 3727): - ester type very high pressure grease (code letter A), operating range from – 73 °C to 121 °C or, - synthetic hydrocarbons type very high pressure grease general purpose (code letter B) operating range from – 54 °C to 177 °C. Their field of application when lubricated with code letter A grease is limited to 121 °C.

Aerospace series - Bearings, airframe rolling - Rigid single row ball bearings in corrosion resisting steel, with flanged alignment housing - Dimensions and loads

ICS
49.035
CCS
V22
发布
2007-07-31
实施
2007-07-31

This standard specifies the characteristics of rigid single row ball bearings, in corrosion resisting steel, reduced internal radial clearance, diameter series 8 and 9 1), designed to withstand only slow rotations and oscillations under load. They are intended for use between fixed and moving parts of the aircraft structure and their control mechanisms. They are intended to be used in the temperature range: – 54 °C to 150 °C. However, being lubricated with the following greases: - very high pressure grease, ester type (code A), operational range – 73 °C to 121 °C or - very high pressure grease, synthetic hydrocarbons, general purpose (code B), operational range – 54 °C to 177 °C (see EN 3280), their field of application when lubricated with code A grease is limited to 121 °C.

Aerospace series - Bearings, airframe rolling - Rigid single row ball bearings in corrosion resisting steel - Diameter series 8 and 9, reduced internal radial clearance - Dimensions and loads

ICS
49.035
CCS
V22
发布
2007-07-31
实施
2007-07-31

This standard specifies the characteristics of rigid single row ball bearings in steel, with cadmium-plated flanged alignment housing designed to withstand only slow rotations and oscillations under load. They are intended for use in the hubs of torsion lever and in separated supports for airframe/aerospace applications. The airframe rolling bearings defined in this standard may be used in the temperature range from – 54 °C to 150 °C. However, being lubricated with the following greases (see EN 3727): - ester type very high pressure grease (code letter A), operating range from – 73 °C to 121 °C or, - synthetic hydrocarbons type very high pressure grease general purpose (code letter B) operating range from – 54 °C to 177 °C. Their field of application when lubricated with code letter A grease is limited to 121 °C.

Aerospace series - Bearings, airframe rolling - Rigid single row ball bearings in steel with flanged alignment housing, cadmium plated - Dimensions and loads

ICS
49.035
CCS
V22
发布
2007-07-31
实施
2007-07-31

This standard specifies the characteristics of self-aligning double row ball bearings with flanged outer ring in corrosion resisting steel, reduced internal clearance, designed to withstand only slow rotations and oscillations under load. They are intended for use between fixed and moving parts of the aircraft structure and their control mechanisms. They are intended to be used in the temperature range: – 54 °C to 150 °C. However, being lubricated with the following greases: - very high pressure grease, ester type (code A), operational range – 73 °C to 121 °C or - very high pressure grease, synthetic hydrocarbons, general purpose (code B), operational range – 54 °C to 177 °C (see EN 3280), their field of application when lubricated with code A grease is limited to 121 °C.

Aerospace series - Bearings, airframe rolling - Double row self-aligning ball bearings with flanged outer ring in corrosion resisting steel, reduced internal radial clearance - Dimensions and loads

ICS
49.035
CCS
V22
发布
2007-07-31
实施
2007-07-31

This standard was prepared to provide an envelope requirements for an axially swaged, filed attachable, 5000 PSI, tube fitting.

Fitting Assembly, Union, Axially Swaged, Hydraulic, 5080 PSI

ICS
49.080
CCS
V22
发布
2007-07-01
实施

COUPLING BODY, THREADLESS - FLEXIBLE, FIXED CAVITY, SELF-BONDING

COUPLING BODY, THREADLESS - FLEXIBLE, FIXED CAVITY, SELF-BONDING

ICS
49.060
CCS
V22
发布
2007-07-01
实施

FITTING END, THREADLESS - FLEXIBLE, FIXED CAVITY, SELF-BONDING, MALE AND FEMALE DESIGN STANDARD

FITTING END, THREADLESS - FLEXIBLE, FIXED CAVITY, SELF-BONDING, MALE AND FEMALE DESIGN STANDARD

ICS
49.080
CCS
V22
发布
2007-07-01
实施

FITTING ASSEMBLY, TEE, AXIALLY SWAGED, HYDRAULIC, 5080 PSI.Table is about dimensions A through FB, dimensions G through PB, dimensions W through W2B and dimensions W3 through W4B and weights.

FITTING ASSEMBLY, TEE, AXIALLY SWAGED, HYDRAULIC, 5080 PSI

ICS
49.080
CCS
V22
发布
2007-07-01
实施

This SAE Aerospace Standard (AS) covers solid, uncut polytetrafluoroethylene (PTFE) retainers (backup rings) for use in glands in accordance with AS4716. They are for use in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with O-rings, packings and other elastomeric seals for static and dynamic applications. Because of the construction of groove dimensions, backup rings specific to rod applications are designated "R" Rod (Female), backup rings specific to piston applications are designated "P" - Piston (Male). Piston and rod types of virgin pigmented PTFE are also identified by color code which also distinguishes parts to this standard from those made from virgin PTFE to other standards. Backup rings specified herein have been designed for a temperature range of -65 to 275 °F (-54 to 135 °C) and a nominal operating pressure of 3000 psi (20.7 MPa) for code 09 material (AMS 3678/9). Alternate materials to AMS 3678 are offered for more arduous operating conditions. This specification includes material tests but does not include hydraulic or pneumatic performance tests.

Retainers (Backup Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Solid, Un-Cut, For Use in AS4716 Glands

ICS
49.080
CCS
V22
发布
2007-07-01
实施

FITTING, LUBRICATION, HYDRAULIC, SURFACE CHECK, .250-28 TAPER THREADS, STEEL, TYPE ITABLE 1 - DIMENSIONS AD WEIGHTS

Fitting, Lubrication, Hydraulic, Surface Check, .250-28 Taper Threads, Steel, Type I

ICS
49.080
CCS
V22
发布
2007-07-01
实施

This SAE Aerospace Standard (AS) covers scarf-cut polytetrafluoroethylene (PTFE) retainers (backup rings) for use in glands in accordance with AS4716. They are for use in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with O-rings, packings and other elastomeric seals for static and dynamic applications. Because of the construction of groove dimensions, backup rings specific to rod applications are designated "R" Rod (Female), backup rings specific to piston applications are designated "P" - Piston (Male). Piston and rod types of virgin pigmented PTFE are also identified by color code which also distinguishes parts to this standard from those made from virgin PTFE to other standards. Backup rings specified herein have been designed for a temperature range of -65 to 275 °F (-54 to 135 °C) and a nominal operating pressure of 3000 psi (20.7 MPa) for code 09 material (AMS 3678/9). Alternate materials to AMS 3678 are offered for more arduous operating conditions. This specification includes material tests but does not include hydraulic or pneumatic performance tests.

Retainers (Backup Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Single Turn, Scarf-Cut, For Use in AS4716 Glands

ICS
49.080
CCS
V22
发布
2007-07-01
实施

FITTING, LUBRICATION, HYDRAULIC, THROAT OR SURFACE CHECK, 1/8 PIPE THREADS, NICKEL-COPPER ALLOY, TYPE VTABLE 1 - DIMENSIONS AD WEIGHTS

Fitting, Lubrication, Hydraulic, Throat or Surface Check, 1/8 Pipe Threads, Nickel-Copper Alloy, Type V

ICS
49.080
CCS
V22
发布
2007-07-01
实施

This procedure establishes the instructions to prepare tube ends and install and inspect axially swaged permanent tube fittings qualified to AS 5958. This procedure is applicable when specified on the engineering drawing or in the procurement document.

Axially Swaged Fittings, Installation and Inspection Procedure

ICS
49.080
CCS
V22
发布
2007-07-01
实施

This SAE Aerospace Standard (AS) establishes the requirements for a V-band grooved clamp couplings that are intended for use on fluid-line tubing joints, tailpipe joints, and accessory mount joints, on flight vehicles or other attachments. The semi-rigid coupling joint assemblies, hereafter referred to as "the joint", shall operate within the temperature ranges specified in their applicable part standards.

Couplings, Clamp, Grooved, V-Band

ICS
49.080
CCS
V22
发布
2007-07-01
实施



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号