V22 机械配件、构件 标准查询与下载

BS ISO 14623:2004 航天系统.压力容器和压力构件.设计和操作

This International Standard, based on general space experience and practice, specifies general and detailed requirements for metallic pressure vessels, composite overwrapped pressure vessels with metallic liners and metallic pressurized structures used in space systems. It is not applicable to pressure components (lines, fittings, valves, hoses, etc.) or to special pressurized hardware (batteries, heat pipes, cryostats and sealed containers).

Space systems - Pressure vessels and pressurized structures - Design and operation

SAE AMS7490P-2004 奥氏体铁、镍或钴合金或沉淀硬化合金、耐腐蚀耐热奥氏体钢制闪光焊接环材

This specification covers flash welded rings made of corrosion and heat resistant austenitic steels and austenitic-type iron, nickel, or cobalt alloys, or precipitation- hardenable alloys. These rings have been used typically for parts, such as flanged casing and seal rings, requiring both corrosion and heat resistance, but usage is not limited to such applications.

Rings, Flash Welded, Corrosion and Heat Resistant Austenitic Steels, Austenitic-Type Iron, Nickel, or Cobalt Alloys, or Precipitation-Hardenable Alloys

SAE AMS7311G-2004 0.50Mo 0.50Cu离心铸造合金铁活塞环

This specification covers a centrifugally-cast, alloyed iron in the form of sleeves for the fabrication of piston rings. Primarily for use as top compression rings in aircraft piston engines. Rings usually require chromium plating for compatibility with the cylinder barrel material.

Piston Rings, Centrifugally-Cast Alloyed Iron 0.50Mo - 0.50Cu

SAE AS8914A-2004 耐摩擦飞机机架自动调心滚子轴承

This specification covers the requirements for nonseparable antifriction roller bearings.

(R) Bearing, Roller, Self-Aligning, Airframe, Antifriction FSC 3110; Should Be Used Instead of MIL-B-8914B(3), Which Was Cancelled on 30 August 1999

AIAA S-096-2004 航天系统.飞轮转子组件

This document establishes a top level certification standard for the design, analysis, material selection and characterization, fabrication, test and inspection of the flywheel rotor assembly (FRA) in a flywheel used for energy storage and/or attitude control in manned and unmanned space systems.

Space Systems Flywheel Rotor Assemblies

SAE AS4775A-2004 航空器维修支架.一般要求

This document covers the general requirements for hydraulic aircraft jacks. It can be applied to tripod, unipod, and axle jacks that may be used on open ramp areas as well as in the aircraft hanger. Throughout this Aerospace Standard, the minimum essential criteria are identified by the key word shall. Recommended criteria are identified by use of the key word should. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety. The term vertical load throughout this Aerospace Standard is defined as the force imposed on the aircraft jack at the airframe jack point.

Aircraft Maintenance Jacks - General Requirements

DLA MS51926 REV B VALID NOTICE 4-2004 1级及2级I型带尾夹

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

CLIP, END, STRAP-TYPE I, CLASS 1 AND CLASS 2

SAE AS81934/2A-2004 自润滑法兰滑动轴承-65鳩至325鳩

(R) BEARING, SLEEVE, FLANGED, SELF-LUBRICATING, -65 °F TO 325 °F FSC 3120;TABLE 1 - DIMENSIONS AND WEIGHTS;TABLE 2 - SLEEVE BEARING LENGTH;TABLE 3 - OVERSIZE BEARING DIMENSIONS 2/;

(R) BEARING, SLEEVE, FLANGED, SELF-LUBRICATING, -65 °F TO 325 °F FSC 3120

DLA MS35311 REV A VALID NOTICE 3-2004 UNC-2A素装饰铜合金镀镍六角型头帽螺杆

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

SCREW, CAP, HEXAGON HEAD, NICKEL-COPPER ALLOY, PLAIN FINISH, UNC-2A

SAE AIR5431-2004 检修工具

This SAE Aerospace Information Report (AIR) offers information about the use of support tooling for composite repair processes, as well as descriptions of some of the different tooling materials used and their applications. If the report document requires the use of tooling, refer to this AIR for additional information.

Repair Tooling

DLA MS35312 REV A VALID NOTICE 3-2004 UNF-2A素装饰铜合金镀镍六角型头帽螺杆

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at www.dodssp.dla.mil

SCREW, CAP, HEXAGON HEAD, NICKEL-COPPER ALLOY, PLAIN FINISH, UNF-2A

DLA MS35309 REV C VALID NOTICE 3-2004 UNC-2A素装饰海军黄铜六角型头帽螺杆

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

SCREW, CAP, HEXAGON HEAD - NAVAL BRASS, PLAIN FINISH, UNC-2A

DLA MS35310 REV B VALID NOTICE 2-2004 UNC-2A素装饰海军黄铜六角型头帽螺杆

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

SCREW, CAP, HEXAGON HEAD, NAVAL BRASS, PLAIN FINISH, UNF-2A

DLA MS70109 REV A VALID NOTICE 4-2004 1级II型带尾夹

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.

CLIP, END, STRAP TYPE II, CLASS 1

ISO 14623:2003 航天系统.压力容器及承压结构.设计与操作

This International Standard, based on general space experience and practice, specifies general and detailed requirements for metallic pressure vessels, composite overwrapped pressure vessels with metallic liners and metallic pressurized structures used in space systems. It is not applicable to pressure components (lines, fittings, valves, hoses, etc.) or to special pressurized hardware (batteries, heat pipes, cryostats and sealed containers).

Space systems - Pressure vessels and pressurized structures - Design and operation

HB 0-11-2003 加强槽

本标准规定了在铝合金和镁合金板零件上制加强槽的形式和尺寸。

Strengthen slots

HB 0-50-2003 螺纹孔的倒角和环槽

本标准适用于任何公制螺纹螺纹孔的倒角和环槽。

Chamfer and Ring Groove of Thread Hole

HB 0-13-2003 加强窝

本标准适用于铝合金和20钢的钣金件。

Strengthen pits

HB 0-14-2003 弯边减轻孔

本标准适用于铝合金和20钢的钣金件。

Reduce weight holes with bending rim

HB 0-16-2003 直角减轻孔

本标准适用于铝合金和20钢的钣金件。

90°Reduce weight holes with bending rim