V22 机械配件、构件 标准查询与下载

HB 0-15-2003 60°弯边减轻孔

本标准适用于铝合金和镁合金的钣金件。

60°Reduce weight holes with bending rim

HB 0-16-2003 直角减轻孔

本标准适用于铝合金和20钢的钣金件。

90°Reduce weight holes with bending rim

HB 0-17-2003 凸弯边

Convex bending rim

HB 0-14-2003 弯边减轻孔

本标准适用于铝合金和20钢的钣金件。

Reduce weight holes with bending rim

DLA MS51495 NOTICE 3-2003 圆头外部应力螺杆

MS51495, dated 10 July 1984, is hereby reactivated and may be used for either new or existing design acquisition.

SCREW, EXTERNALLY RELIEVED BODY, FILLISTER HEAD

DLA MS51849 REV A NOTICE 3-2003 NF-2A 和 UNC-2A狭槽六角形钢头机械螺杆

MS51849A, dated 15 October 1987, is hereby reactivated and may be used for either new or existing design acquisition.

SCREW, MACHINE - STEEL HEXAGON HEAD, SLOTTED, UNF-2A AND UNC-2A

BS EN 12312-4:2003 航空器地面支持设备.特殊要求.乘客登机桥

This European Standard specifies the technical requirements to minimise the hazards listed in clause 4 which can arise during the commissioning, operation and maintenance of PBB's when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some require-ments recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This standard applies to: — apron-drive bridges; — fixed-head bridges (also referred to as nose-loaders) or pedestal bridges; — suspended bridges, for embarking/disembarking of passengers. It is applicable from the interface of the building to the connection with the aircraft. An example of a typical PBB is shown in annex A. This standard does not apply to: — elevating lounges; — passenger stairs; — other forms of aircraft access equipment or to the fixed building structure to which the PBB interfaces. This standard does not establish requirements for hazards caused by noise and vibration. This Part of EN 12312 is not applicable to PBB's which are manufactured before the date of publication of this standard by CEN.

Aircraft ground support equipment - Specific requirements - Passenger boarding bridges

BS EN 12312-3:2003 航空器地面支持设备.特殊要求.输送带式运输装置

This European Standard specifies the technical requirements to minimise the hazards listed in clause 4 which can arise during the commissioning, operation and maintenance of conveyor belt vehicles when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlines and handling agencies. This standard applies to: — self-propelled conveyor belt vehicles with or without driver's accommodation; — self-propelled conveyor belt vehicles equipped with a van body; — towed conveyor belt vehicles, Intended to be used for manual loading/unloading of aircraft. Examples of typical designs of conveyor belt vehicles are given in annex A. This standard does not apply to pneumatic systems and to cableless remote controls. This standard does not establish requirements for hazards caused by noise and vibration. This Part of EN 12312 is not applicable to conveyor belt vehicles which are manufactured before the date of publication of this standard by CEN.

Aircraft ground support equipment - Specific requirements - Conveyor belt vehicles

SAE AS28913B-2003 (R) FSC 3110 II型密封式机身用耐磨双排自动校准式滚筒轴承.代替1998年9月2日作废的MS28913D

(R) BEARING, ROLLER, SELF-ALIGNING, DOUBLE ROW AIRFRAME, ANTI-FRICTION, SEALED, TYPE II FSC 3110; Should Be Used Instead of MS28913D, Which Was Cancelled on 02 September 1998THE TABLE IS ABOUT MS DASH NO., WT MAX LB, STATIC LIMIT LOAD-LB, DYNAMIC LOAD RATING-LB

(R) BEARING, ROLLER, SELF-ALIGNING, DOUBLE ROW AIRFRAME, ANTI-FRICTION, SEALED, TYPE II FSC 3110; Should Be Used Instead of MS28913D, Which Was Cancelled on 02 September 1998

SAE AS28914B-2003 (R)FSC 3110 III型密封抗摩擦双排机架用自对准滚珠轴承.代替1998年9月2日作废的MS28914D标准

(R) BEARING, ROLLER, SELF-ALIGNING, DOUBLE ROW AIRFRAME, ANTI-FRICTION, SEALED, TYPE III FSC 3110; Should Be Used Instead of MS28914D, Which Was Cancelled on 02 September 1998THE TABLE IS ABOUT MS DASH NO., WT MAX LB, STATIC LIMIT LOAD-LB, DYNAMIC LOAD RATING-LBTHE TABLE2 IS ABOUT RADIAL INTERNAL CLEARANCE GROOVE WIDTH MIN. ETC..

(R) BEARING, ROLLER, SELF-ALIGNING, DOUBLE ROW AIRFRAME, ANTI-FRICTION, SEALED, TYPE III FSC 3110; Should Be Used Instead of MS28914D, Which Was Cancelled on 02 September 1998

DLA MS28774 REV L NOTICE 1-2003 四氟乙烯单转向支持包装固定器

MS28774L is inactive for new design and is no longer used, except for replacement purposes. For new designs use SAE-AS8791.

RETAINER, PACKING BACKUP, SINGLE TURN TETRAFLUOROETHYLENE

DLA MS28774 REV L (2)-2003 四氟乙烯单转向支持包装固定器

This amendment forms a part of MS28774L dated 19 Novemb er 1990 and is approved for use by all Departments and Agencies of the Department of Defense.

RETAINER, PACKING BACKUP, SINGLE TURN TETRAFLUOROETHYLENE

DLA MS35689 REV A VALID NOTICE 1-2003 (弹簧装载)V 轴承

MS35689A, dated 1 September 1993, has been reviewed and determined to be valid for use in acquisition

V-BEARING (SPRING LOADED)

BS EN 4585:2003 航空航天系列.弹簧夹.技术规范

This standard specifies the characteristics, qualification and acceptance requirements for spring tension clips for the support of electrical harnesses, in alloy steel for aerospace applications. It is applicable whenever referenced.

Aerospace series - Clips, spring tension - Technical specification

SAE AIR5926-2003 AS8879C代替MIL-S-8879C用白页

This paper was prepared to support supersession of MIL-S-8879C with screw thread conformity task force selected industry standard AS8879C, published by the Society of Automotive Engineers (SAE). Other documentation changes will be covered by separate papers. Separate papers are anticipated for thread gaging issues, and thread gage calibration procedures. THE STC-TF decided that the thread design standard needed to be completed before thread gage definition could be addressed. Thread gage definition has to be known before calibration procedures can be addressed.

White Paper to Support Supersession of MIL-S-8879C With AS8879C

HB 8083～8086-2002 带减轻孔双螺栓侧面固定夹紧卡箍

Grip clamp with cushion fixed fland using double bolts and lighening hole

HB 8117-2002 片状接线端子

Flaky connetor

HB 2-25-2002 挤压型材合页片

本标准规定了撞让型材合页片的结构、尺寸要求。 本标准适用寺盖板，舱门和挡板饼链用合页片。

Extruding shapes hinge

HB 2-62-2002 链条

本标准规定了链条的结构、尺寸要求。 本标准适用于连接可拆印的舱口盖和其它部件以及产品的类似组件和零件用的链条。

Chain

HB 2-66-2002 耳环绳带

Lug rope