共找到 2047 条与 机械配件、构件 相关的标准,共 137 页
本标准规定了锁紧垫片锁紧的操纵拉杆管子的结构、尺寸要求。 本标准适用于飞机和直升机锁紧垫片锁紧的操纵拉杆。
Control rod,locked with locking gasket Pole
本标准规定了直径公差带 z7和 "8 圆柱销(以下简称圆柱销〉的结构和尺寸。 本标准适用于机械定位连接。
Diameter tolerance zone z7 and u8 cylindrical pin (8295)
本标准规定了锁紧垫片锁紧的操纵拉杆用锁紧垫片的结构、.尺士和要求。 本标准适用于飞机和直升机锁紧垫片锁紧的操纵拉杆。
Control rod,locked with locking gasket Locking gasket
本标准规定了锁紧热片锁紧的操纵拉杆用带轴承不可调叉耳接头的结构、尺十和要求。 本标准适用于飞机和直升机锁紧垫片锁紧的操纵拉杆。
Control rod,locked with locking gasket Tie-in with bush
Aerospace series - Clips, spring tension, three parts - Inner clips in heat resisting steel FE-PA92HT (A286)
Aerospace series - Clips, spring tension, three parts - PTFE bushes
Aerospace series - Clips, spring tension, three parts - Outer clips in heat resisting steel FE-PA92HT (A286)
MS51494, dated 10 JULY 1984, remains inactive for new design, however, the document is valid for acquisition when needed.
SCREW, EXTERNALLY RELIEVED BODY, FLAT COUNTERSUNK HEAD, 100 DEGREE, CROSS-RECESSED
MS91527B, dated 8 DECEMBER 1958, remains inactive for new design, however, the document is valid for acquisition when needed.
MOUNT, VIBRATION, CUP-TYPE, CLASSES A-B (FOR USE WITH ELECTRONIC EQUIPMENT IN AIRCRAFT)
Aerospace series - Aerospace series - Welded and brazed assemblies for aerospace constructions - Weldability and brazeability of materials - Part 20 : homogeneous assemblies aluminium and aluminium alloys.
Aerospace series - Welded and brazed assemblies for aerospace constructions - Weldability and brazeability of materials - Part 10 : general requirements.
MS35295B, dated 9 JUNE 1967 remains inactive for new design, however, the document is valid for acquisition when needed.
SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT), MEDIUM CARBON STEEL, PLAIN FINISH UNC-2A
MS35302C, dated 14 JUNE 1971 remains inactive for new design,however, the document is valid for acquisition when needed.
SCREW, CAP, HEXAGON HEAD (FINISHED HEXACON BOLT), ALLOY STEEL, PLAIN FINISH, UNF-2A
This method outlines the standard procedure for testing the hardness of bearing components. Bearings covered by this test method shall be any rolling element bearing used in airframe control.
Rolling Element Bearing Hardness Test
Technical requirements for non-destructive testing of aerospace materials and parts and components (assemblies)
AN3048 REV 4 remains inactive for new design, however, the document is valid for use.
FERRULE- CONDUIT, FLEXIBLE, ONE STEP, SYNTHETIC COVERED
A-A-59174, dated 1 April 1998, has been reviewed and determined to be valid for use in acquisition
PRESS, ARBOR, MECHANICAL, HAND OPERATED [Superseded: DLA A-A-51196 CANC NOTICE 1, DLA A-A-51196, DLA A-A-51197 CANC NOTICE 1, DLA A-A-51197, DLA A-A-51198 CANC NOTICE 1, DLA A-A-51198, DLA A-A-51199 CANC NOTICE 1, DLA A-A-51199]
This specification covers bearings cast on one or both faces of a steel backing. Primarily for shims, thrust washers, bushings and bearings.
Bearings, Leaded Copper 70 Cu - 28.5Pb Steel Back UNS C98400
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号