V22 机械配件、构件 标准查询与下载

HB 7710-2002 飞机座舱盖加温加载疲劳试验要求

本标准规定了飞机座舱盖加温加载疲劳试验要求。 本标准适用于飞机座舱盖加温加载疲劳试验，民用飞机也可参照执行。

Requirements of the heating and loading fatigue test of the canopy for the aircraft

HB 7717-2002 航空钢制件磨削烧伤酸侵蚀检查

Acid etch inspection of grinding burn of steel parts for aviation

HB 7714-2002 飞机结构疲劳试验通用要求

General requirements of fatigue test for aircraft structure

HB 6502-2002 飞机结构刚度试验通用要求

本标准规定了飞机结构刚度试验的目的、内容、方法及要求，这些内容仅对飞机结构刚度试验提供指导和说尽具体的实施办法。 　　本标准适用于各种军用飞机结构（不含直升机）的刚度试验，民用飞机亦可参照使用。

General requirements of rigidity test for aircraft structure

HB 7709-2002 飞机复合材料结构机械连接设计要求

本标准规定了飞机复合材料结构机械连接的设计要求。 本标准适用于飞机的各类增强纤维/类脂基复合材料结构的机械连接及金属与复合材料结构的机械 连接;直升机上类似的复合材料结构的机械连接可参照使用。

Design requirements of mechanically fastened joint of composite structure for airplane

DLA MS17815 REV B (1)-2002 飞机场灯的索卡

This amendment forms a part of MS17815B, dated 17 JUNE 1983,and is approved for use by all Departments and Agencies of the Department of Defense

CLAMP, CABLE, AVIATION GROUND LIGHTS

NF L31-557:2002 航空航天系列.室温条件下高负荷、宽系列、带自动润滑轴承衬的耐蚀钢制关节轴承.尺寸和负载

Aerospace series - Bearing, spherical plain in corrosion resisting steel with self-lubricating liner - Wide series - Elevated load at ambient temperature - Dimensions and loads.

NF L31-556:2002 航空航天系列.室温条件下高负荷、窄系列、带自动润滑轴承衬的耐蚀钢制关节轴承.尺寸和负载

Aerospace series - Bearing, spherical plain in corrosion resisting steel with self-lubricating liner - Narrow series - Elevated load at ambient temperature - Dimensions and loads.

SAE AS27645B-2002 (R)FSC 3110轻型和重型自对准抗磨机身用滚珠轴承.代替1998年7月23日作废的MS27645E

(R) Bearing, Ball, Airframe, Anti-Friction, Self-Aligning, Light and Heavy Duty FSC 3110; Should Be Used Instead of MS27645E, Which Was Cancelled on 23 July 1998TABLE 1 - DIMENSIONS AND LOADS AND CONTINUED

(R) Bearing, Ball, Airframe, Anti-Friction, Self-Aligning, Light and Heavy Duty FSC 3110; Should Be Used Instead of MS27645E, Which Was Cancelled on 23 July 1998

ISO 12256:2002 航空航天.内十字形槽扳手.米制系列

This International Standard specifies the dimensions of metric internal cruciform ribbed drives used in metric screws in the nominal thread diameter range of 3 mm to 20 mm. Drivers and gauges used in conjunction with these drives are defined in ISO 14280 and ISO 14281.

Aerospace - Drives, internal, cruciform, ribbed - Metric series

DIN EN 3275:2002 航空航天系列.可达28000kPa 的 8°30'管连接件.动态光束密封.公制系列.技术规范; 德文和英文版本 EN 3275:2002

The document establishes the basic performance and quality criteria for metric series 8?0 dynamic beam seal tube fitting assemblies. It standardizes the qualification test and procurement requirements for tube fittings. The test requirements are intended to satisfy the most strenuous demands encountered in a high performance aircraft hydraulic system. Fittings covered by this standard shall be of the temperature types and pressure classes specified in ISO 6771, types II and III, classes B, D and E.#,,#

Aerospace series - Pipe coupling 8°30 up to 28000 kPa - Dynamic beam seal; Metric series; Technical specification; German and English version EN 3275:2002

KS W ISO 12334:2002 航空航天、液压的、压力补偿的、变量输送泵.35000KPa系统的通用要求

이 규격은 35 000 kPa의 항공기 유압 계통에 사용되는 압력 보상식, 가변 용량형 유

Aerospace－Hydraulic, pressure compensated, variable delivery pumps－ General requirements for 35 000 kPa systems

BS ISO 14279:2002 航空航天.内十字槽传动装置.米制系列

This International Standard specifies the dimensions of metric internal cruciform drives used in metric screws in the nominal thread diameter range of 1,6 mm to 20 mm. Drivers and gauges used in conjunction with these drives are defined in ISO 14280 and ISO 14281.

Aerospace - Drives, internal, cruciform - Metric series

BS ISO 14281:2002 航空航天.内十字加肋或无肋传动装置的量规.米制系列

This International Standard specifies the dimensions of metric gauges which check internal cruciform drives, ribbed or unribbed, used in metric screws in the nominal thread diameter range of 1,6 mm to 20 mm. The internal cruciform drives, ribbed and unribbed, are defined respectively in ISO 12256 and ISO 14279.

Aerospace - Gauges, for internal cruciform ribbed or unribbed drives - Metric series

BS ISO 14280:2002 航空航天.内十字槽加肋或无肋传动装置的加肋改锥.米制系列

This International Standard specifies the dimensions of metric ribbed drivers which are inserted into internal cruciform ribbed or unribbed drives used in metric screws in the nominal thread diameter range of 1,6 mm to 20 mm. The internal cruciform drives, ribbed and unribbed, are defined respectively in ISO 12256 and ISO 14279.

Aerospace - Drivers, ribbed, for internal cruciform ribbed or unribbed drives - Metric series

BS ISO 14278:2002 航空航天.内偏置十字槽加肋或无肋传动装置的量规.公制系列

This International Standard specifies the dimensions of metric gauges which check internal offset cruciform drives, ribbed or unribbed, used in metric screws in the nominal thread diameter range of 1,6 mm to 20 mm. The internal offset cruciform drives, ribbed drives and unribbed, respectively are defined in ISO 14275 and ISO 14276.

Aerospace - Gauges, for internal offset cruciform ribbed or unribbed drives - Metric series

BS ISO 14277:2002 航空航天.内偏置十字槽加肋或不加肋的传动装置的加肋改锥.米制系列

This International Standard specifies the dimensions of metric ribbed drivers which are inserted into internal offset cruciform ribbed or unribbed drives used in metric screws in the nominal thread diameter range of 1,6 mm to 20 mm. The internal offset cruciform, ribbed drives and unribbed drives, respectively are defined in ISO 14275 and ISO 14276.

Aerospace - Drivers, ribbed, for internal offset cruciform ribbed or unribbed drives - Metric series

BS ISO 14275:2002 航空航天.加肋的偏置十字形内传动改锥.米制系列

This International Standard specifies the dimensions of metric internal, offset cruciform, ribbed drives used in metric screws in the nominal thread diameter range of 3 mm to 20 mm. Drivers and gauges used in conjunction with these drives are defined in ISO 14277 and ISO 14278.

Aerospace - Drives, internal, offset cruciform, ribbed - Metric series

SAE ARP5448/7-2002 平面轴承的磨损度测定

This standard details two methods of inspecting TFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the dynamic test. The two methods described are: a. destructive inspection - cut and measure (not applicable to molded liners); and b. non-destructive inspection - radial play (gage) measurement.

Plain Bearing Wear Measurement

DIN EN 2584:2002 航空航天系列.带自动润滑内衬的耐腐蚀钢制球面滑动轴承.窄系列:室温下提高的负荷:尺寸和负载; 德文版本 EN 2584:2001

Aerospace series - Bearings, spherical plain in corrosion resisting steel with self-lubricating liner - Narrow series; Elevated loads at ambient temperature; Dimensions and loads; German version EN 2584:2001