V22 机械配件、构件 标准查询与下载

SAE ARP1341B-2001 碳钢和低合金钢成品零件脱碳和渗碳的测定

This document provides a recommended practice for determining decarburization and carburization in heat treated carbon and low-alloy steel parts other than case hardened parts. It is not applicable to raw materials.

Determining Decarburization and Carburization in Finished Parts of Carbon and Low-Alloy Steels

SAE ARP5448/8-2001 滑动球面轴承径向和轴向间隙的测量

This test method provides a guidance for determining the total free play between the ball and outer ring of a spherical bearing when measured in both the radial and axial directions. Bearings covered by this test method include all plain spherical type bearings. Both self-lubricated (lined) and metal-to-metal.

Plain Spherical Bearing Radial and Axial Clearance Measurement

BS ISO 9762:2001 航空器操纵钢丝绳组件.尺寸规格及端部配件组合

This International Standard specifies the possible combinations and lengths of preformed flexible steel wire ropes for aircraft controls equipped with two end-fittings swaged on each end of the cable and the corresponding designations.

Aircraft control wire rope assemblies - Dimensions and end-fitting combinations

BS ISO 9759:2001 航空器操纵钢丝绳上的锻制耐腐蚀钢制叉形端.尺寸规格及载荷

This International Standard specifies the characteristics of fork-ends in corrosion-resistant steel swaged on aircraft control wire rope.

Fork ends, in corrosion-resistant steel, swaged on aircraft control wire rope - Dimensions and loads

BS ISO 9747:2001 航空器操纵钢丝绳上的锻制耐腐蚀钢双柄球端.尺寸规格及载荷

This International Standard specifies the characteristics of double-shank ball-ends in corrosion-resistant steel swaged on aircraft control wire rope.

Double shank ball-ends, in corrosion-resistant steel, swaged on aircraft control wire rope - Dimensions and loads

BS ISO 9749:2001 航空器操纵钢丝绳上的锻制耐腐蚀钢螺柱端.尺寸规格及载荷

This International Standard specifies the characteristics of stud-ends in corrosion-resistant steel swaged on aircraft control wire rope.

Stud-ends, in corrosion-resistant steel, swaged on aircraft control wire rope - Dimensions and loads

BS ISO 9737:2001 航空器操纵钢丝绳用锻制耐腐蚀钢有眼端.尺寸及载荷

This International Standard specifies the characteristics of eye-ends in corrosion-resistant steel swaged on aircraft control wire rope.

Eye-ends, in corrosion resisting steel, swaged on aircraft control wire rope - Dimensions and loads

BS ISO 9738:2001 航空器操纵钢丝绳用旋转套筒.尺寸及载荷

This International Standard specifies the characteristics of turnbarrels for aircraft control wire rope in either low alloy steel, corrosion-resistant steel, copper-zinc alloy or aluminium alloy.

Turnbarrels, for aircraft control wire rope - Dimensions and loads

BS ISO 9758:2001 航空器操纵钢丝绳用滚动轴承的螺纹式钢制叉形端.尺寸及载荷

This International Standard specifies the characteristics of fork-ends for rolling bearings, in either low alloy steel or corrosion-resistant steel, for aircraft control wire rope.

Fork-ends, in corrosion-resistant steel, threaded, for rolling bearings, for aircraft control wire rope - Dimensions and loads

BS ISO 9761:2001 航空器操纵钢丝绳旋转套筒用耐腐蚀钢制锁定卡.尺寸

This International Standard specifies the characteristics of locking clips in corrosion-resistant steel for aircraft control wire rope turnbuckles.

Locking clips, in corrosion-resistant steel, for aircraft control wire rope turnbuckles - Dimensions

BS ISO 9757:2001 航空器操纵钢丝绳旋转套筒用耐腐蚀钢制螺纹式叉形端.尺寸及载荷

This International Standard specifies the characteristics of fork-ends, in either low alloy steel or corrosion-resistant steel, for aircraft control cable turnbarrels.

Fork-ends, in corrosion-resistant steel, threaded, for aircraft control wire rope turnbarrels - Dimensions and loads

BS ISO 9748:2001 航空器操纵钢丝绳上锻制的耐腐蚀钢制球端.尺寸及载荷

This International Standard specifies the characteristics of ball-ends in corrosion-resistant steel swaged on aircraft control wire rope.

Ball-ends, in corrosion-resistant steel, swaged on aircraft control wire rope - Dimensions and loads

SAE AS81819-2001 高速震荡自润滑滑动轴承(自调.套筒和止推).通用规范

This specification covers the requirements for sliding spherical, sleeve, and thrust self-lubricating bearings which are for use in the ambient temperature range -65°F to +160°F at high cyclic speeds.

Bearing, Plain (Self-aligning, Sleeve and Thrust), Self- Lubricating, High Speed Oscillation, General Specification for

SAE AS26805-2001 气体压缩机装置的一般要求

This specification covers the general requirements for the design and construction of air/gas compressor units (see 6.4.1). The detail requirements for a particular air compressor unit shall be as specified in the individual equipment specification for that particular air compressor unit (see 6.2).

Compressor Units, Air/Gas, General Requirements for

SAE ARP5448/9-2001 滑动轴承衬里内径规

This test method establishes a standard procedure for using plug gages to evaluate dimensional conformance of line inside diameters of bearings. Bearings covered by this test method include sleeve bearings and lined bore spherical bearings. Note that this method gives no indication of true cylindricity.

Plain Bearing Lined Inside Diameter Plug Gaging

AECMA PREN 4538-2-2001 航空航天系列.具有自润滑轴套的球面防腐钢轴承 窄系列 环境温度下的高-荷 尺寸和-荷 P.第1版

This standard defines terms for optical fibres and cable.

Aerospace Series Bearings, Spherical Plain, in Corrosion Resisting Steel with Self-Lubricating Liner Elevated Load under Low Oscillations Narrow Series Dimensions and Loads Inch Series Edition P 1

AECMA PREN 4539-2-2001 航空和航天系列.标准系列自润滑油封钢制耐腐蚀球头螺栓.尺寸和-载 P.第1版

This industrial standard for the aerospace sector has been drawn up uner the responsibility of AECMA.

Aerospace Series Bearings, Spherical Plain, in Corrosion Resisting Steel with Self-Lubricating Liner Elevated Load under Low Oscillations Wide Series Dimensions and Loads Inch Series Edition P 1

AECMA PREN 4538-1-2001 航空航天系列.具有自润滑轴套的球面防腐钢轴承 窄系列 环境温度下的高-荷 尺寸和-荷 P.第1版

This draft is now available for public comment and your views and technical comments on it would be appreciated. I f you have no specific comments to make but find it generally acceptable it would be helpful if you would notify us accordingly. Suggestions entailing revision of the text should indicate the preferred wording.

Aerospace Series Bearings, Spherical Plain, in Corrosion Resisting Steel with Self-Lubricating Liner Elevated Load under Low Oscillations Narrow Series Dimensions and Loads Metric Series Edition P 1

AECMA PREN 3727-2001 航空航天系列.有法兰式定位盖的飞机机架用硬质滚动轴承　尺寸和负荷

This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members.

Aerospace Series Bearings, Airframe Rolling Rigid with Flanged Alignment Housing Dimensions and Loads Edition P 2

AECMA PREN 4540-2001 航空航天系列.轴承球形抗腐蚀钢自动润滑线荷重低摇摆技术规范.P1版

This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published on green paper for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments.

Aerospace Series Bearings, Spherical Plain, in Corrosion Resisting Steel with Self-Lubricating Liner Elevated Load under Low Oscillations Technical Specification Edition P 1