共找到 548 条与 航空器及其附件综合 相关的标准,共 37 页
本标准规定了刚性单面印制线路板、双面印制线路板和多层印制线路板及其组装件的设计要求,元器件和组装件安装的设计依据。按本标准设计的组装件应涂覆印制板组装件涂覆层。 本标准适用于航空电子、电气设备用印制线路板及其组装件的设计。
Printed circuit design for aviation
Built-In Test Equipment (BITE)
Built-In Test Equipment (BITE)
MIL-P-85486(AS) dated 30 June 1982, has been reviewed and determined
POWER UNIT AUXILIARY, S-3A AIRCRAFT EQUIPMENT SPECIFICATION FOR
本标准规定了军用固定翼单座或串列双座杆式操纵歼击机、强击机、歼击轰炸座舱几何尺寸的设计要求。使之保证在规定的人体尺寸范围内,飞行员能安全、有效和舒适地进行操纵。 本标准适用于新研制的飞机。当某特定新型飞机座舱设计尺寸超出本标准时,可制定该机型专用要求,并在样机审查时批准。
Aircraft cockpit geometry
本指南包括了航空机轮设计要求、性能计算和热载计算、结构设计、摩擦偶设计、强度和刚度的计算及验算,疲劳设计、寿命估算和寿命评估,轴承选择及试验验证等内容。
Aviation Wheel Design Guide
本标准对液压恒速传动装置和轴向齿轮差动式恒速传动装置规定了产品的设计、性能和试验的通用技术要求。 本标准是制订专用技术条件的基础。若无特殊要求,均以本标准为准。如有超出其要求时,应在专用技术条件中另行规定,两者有矛盾时,则应以专用技术条件为准。
General technical specifications for aircraft power supply constant speed transmission
本标准规定了两类稳态加速度试验,并规定了四种加速度严格等级来模拟飞机设备使用中可能遇到的慢变加速度环境。 本标准适用于民用飞机机载设备承受机动过载或阵风过载的加速度的加速度环境试验。强迫着陆参考HB6167.5《民用飞机机载设备环境条件和试验方法 飞行冲击和坠撞安全》。
Environmental conditions and test methods for airborne equipment of civil aircraft Acceleration
This specification covers a one-part, ready to use adhesive, suitable for use in bonding demolition charges to dry,wet and underwater surfaces of al1 types of structural materials, under all weather conditions .
ADHESIVE FOR BONDING DEMOLITION CHARGES TO STRUCTURAL SURFACES
MIL-H-85330A(AS), dated 17 April 1981, has been reviewed and determined to be current.
HYBRID TEST SYSTEM
This specification covers the general requirements for the design and installation of gaseous oxygen (450 and 1800 pounds per square inch gage (psig) (3.1 MPa and 12.4 MPa) systems inaircraft .
DESIGN AND INSTALLATION OF GASEOUS OXYGEN SYSTEMS IN AIRCRAFT, GENERAL SPECIFICATION FOR
Built-In Test Equipment (BITE)
Built-In Test Equipment (BITE)
Provisions for Automatic Test Equipment
Provisions for Automatic Test Equipment
This «Aerospace Series» pre-standard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved b y the experts of the concerned AECMA Commission following comment by the Member countries.
Aerospace Series Bearings, Spherical Plain in Corrosion Resisting Steel with Self-Lubricating Liner, Light Series Elevated Loads at Ambient Temperature Dimensions and Loads Issue P 1
This standard contains general directions concerning maintenance and repair of aircraft glazings of acrylic plastics according to WL 5.1411, WL 5.1412, WL 5.1414, WL 5.1415 and WL 5.1416 included in the German aviation materials manual, part II.
Aerospace; maintenance and repairing of aircraft glazings of acrylic plastics; general directions
Provisions for Automatic Test Equipment
Provisions for Automatic Test Equipment
Built-In Test Equipment (BITE)
Built-In Test Equipment (BITE)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号