共找到 548 条与 航空器及其附件综合 相关的标准,共 37 页
航空气瓶通用技术条件适用于最大公称工作压力不超过20.59MPa的球形、圆柱形整体式和焊接式的钢制气瓶、用于盛装压缩空气、氧气、氮气及灭火剂等,使用环境温度为-55℃~+70℃(碳素钢气瓶为-30℃~+60℃)。
General technical requirements for aviation gas cylinders
This "Aerospace Series" pre-standard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Commission following comment by the Member countries.
Aerospace Series Bearings-Airframe Rolling Rigid Two Row Ball Bearings in Steel Cadmium Plated Dimensions and Loads Issue P 1
This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.
Aerospace Series Bearings-Airframe Rolling Rigid Two Row Ball Bearings in Corrosion Resisting Steel Dimensions and Loads Issue P 1
Adjustment of the lading or securing mechanisms, or reconditioning of the bracing or items of securement is not allowed without a complete retest.
SPREADER, AGGREGATE, TOWED-TYPE, TRACTION-POWERED
This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.
Aerospace Series Bearings-Airframe Rolling Rigid Single Row Ball Bearings in Corrosion Resisting Steel Diameter Series 0 and 2 Reduced Clearance Category Dimensions and Loads Issue P 1
This .Aerospace Series» pre-standard has been drawn up under the responsibility of AECMA (Association Européenne des Constructeurs de Matériel Aérospatial). It is published on green paper for the needs ofAECMA-Members. It has been technically approved by the experts of the concerned AECMA Commission following comment by the Member countries.
Aerospace Series Bearings-Airframe Rolling Single Row Self-Aligning Roller Bearings in Steel Cadmium Plated Dimensions and Loads Issue P 1
This "Aerospace Series" frestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments.
Aerospace Series Bearings-Airframe Rolling Single Row Self-Aligning Roller Bearings in Corrosion Resisting Steel Dimensions and Loads Issue P 1
This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.
Aerospace Series Bearings-Airframe Rolling Rigid Two Row Ball Bearings in Steel Dimensions and Loads Issue P 1
This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee folio wing comment by the Member countries.
Aerospace Series Bearings-Airframe Rolling Rigid Single Row Ball Bearings in Steel Cadmium Plated Diameter Series 0 and 2 Reduced Clearance Category Dimensions and Loads Issue P 1
This specification establishes the general requirements for three phase, f o u r wire, 115/200 v o l t , 400 Hz ac ( a l t e r n a t i n g c u r r e n t ) v a r i a b l e input speed e l e c t r i c power generating channels, herein r e f e r r e d t o as the Generator Package for use on a i r c r a f t .
ELECTRIC POWER GENERATING CHANNEL, VARIABLE INPUT SPEED, ALTERNATING CURRENT, 400 HZ, AIRCRAFT; GENERAL SPECIFICATION FOR
MS18054B(AS), dated 26 April 1965, has been reviewed and determined to be current.
DRIVE PADS FOR AIRCRAFT ELECTRIC EQUIPMENT CIRCULAR, 5, 8 AND 10 INCH
Gives the test procedures and performance requirements for the characteristics of these devices specified in ISO 5065-1 and shall be read in conjunction with it. The requirements shall comply with the details given in the table. It includes contact forces, supply voltage and current consumption, lamps, insulation resistance, thermal shock, low and high temperature operation, damp heat, life, acceleration, vibration, mechanical shock, temperature and altitude, resistance to fluids, drip test, sand and dust.
Aircraft; Magnetic indicators; Part 2 : Tests
Specifies the general operating characteristics and standardization principles. Lays down the basic requirements relating to the mechanical and electrical characteristics as well as the basic environmental conditions in service. ISO 5065-2 gives details of the tests referred to in this part of ISO 5065. Includes design requirements, type approval testing and production and quality testing.
Aircraft; Magnetic indicators; Part 1 : Characteristics
NUMERAL AND LETTER, AIRCRAFT INSTRUMENT DIAL, STANDARD FORM OF
NUMERAL AND LETTER, AIRCRAFT INSTRUMENT DIAL, STANDARD FORM OF
本标准是HB5830《机载设备环境条件及试验方法》系列标准的组成部分,必须与HB5830.1-84《机载设备环境条件及试验方法 总则》,一起使用。
Airborne Equipment Environmental Conditions and Test Methods Salt Spray
本标准是HB5830《机载设备环境条件及试验方法》系列标准的组成部分,必须与HB5830.1-84《机载设备环境条件及试验方法 总则》一起使用。
Airborne equipment environmental conditions and test methods damp heat
本标准是HB5830《机载设备环境条件及试验方法》系列标准的组成部分,必须与HB5830.1-84《机载设备环境条件及试验方法 总则》一起使用。
Airborne Equipment Environmental Conditions and Test Methods Mold
Bite Display Preparation Guidelines
Bite Display Preparation Guidelines
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号