V35 航空器及其附件综合 标准查询与下载

BS 3G 100-2.3.10:1974 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.第10小节:撞冰

The test in this British Standard is applicable to equipment installed in a forward facing location external to an aircraft or in the intake ducting where it may be subjected to the impact of supercooled water droplets or ice crystals, and where under conditions of near or sub-zero temperatures ice may form or accumulate and interfere with the safe operation of the equipment or result in the shedding of ice fragments hazardous to other equipment installed downstream. This standard should be read in conjunction with British Standard 3G.100 : Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Impact icing

BS 3G 100-2.3.14:1973 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.第14小节:声震

This British Standard specifies details of tests to determine the ability of aircraft equipment and components to withstand four grades of acoustic environment. This standard should also be read in conjunction with British Standard 3G. 100 : Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Acoustic vibration

BS 3G 100-2.3.13:1973 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.第13小节:规定防火区的防火性

This British Standard specifies requirements for all components and equipment (contained in designated fire zones) designed and constructed to provide a level of fire resistance not less than a specified minimum. It does not relate to flammability requirements. The standard should also be read in conjunction with British Standard 3G. 100 : Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Resistance to fire in designated fire zones

3G 100 Pt.2 Sec.1-1973 航空用设备的一般要求规范.第2部分:各种设备.第1节:结构

Specification for general requirements for equipment for use in aircraft. All equipment. Construction

BS 3G 100-4.1:1973 飞机设备的一般要求规范.第4部分:电气设备.第1节:结构和总则

This standard specifies general electrical requirements relating to electrical equipment and electrical assemblies or components forming part of electro-raechanical equipment used in aircraft. It should be read in conjunction with British Standard 3G.100 : Part 0.

Specification for general requirements for equipment for use in aircraft - Electrical equipment - Construction and general

BS 3G 100-2.3.11:1973 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.第11小节:防水性

This British Standard specifies tests for two grades of water-proofness applicable to equipment in aircraft which is required to operate when exposed to conditions when water is sprayed on it, as in driving rain, or water dripping on it, such as condensation falling from adjacent aircraft structure. It should also be read in conjunction with British Standard 3G.100: Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Water-proofness

DLA MS35223 REV B-1973 NC-2A及UNC-2A镀镉碳钢开槽机械面板顶部螺旋桨

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

SCREW, MACHINE, PAN HEAD, SLOTTED, CARBON STEEL, CADMIUM PLATED, NC-2A AND UNC-2A

NF L09-004:1972 直升机元件.制造商的零件号

Helicopter components. Manufacturer'S part number.

BS 3G 100-2.2:1972 飞机设备的一般要求规范.第2部分:各种设备.第2节:磁影响

Specification for general requirements for equipment for use in aircraft - All equipment - Magnetic influence

BS 3G 100-2.3.6:1972 航空器设备的一般要求规范.第2部分:全部设备.第3节:环境条件.第6小节:加速要求

This British Standard specifies design and test requirements for equipment in aircraft, some of which is required to operate during and after normal and crash acceleration phases. It relates these requirements to various grades of equipment and classes of acceleration. It does not apply to flight recorders or to passenger and freight restraint systems, for which reference should be made to Air Navigation orders published by the Department of Trade and Industry. The standard should be read in conjunction with British Standard 3G. 100: Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Acceleration requirements

BS 3G 100-2.3.5:1972 航空器设备的一般要求规范.第2部分:全部设备.第3节:环境条件.第5小节:防爆性

This British Standard specifies design require-ments for aircraft equipment that may come into contact with flammable fluids and vapours. It also specifies test requirements to demonstrate that the equipment meets these requirements. The standard does not relate to potentially dangerous environments occurring as a result of leakage from goods carried on board by passengers or as part of their baggage, or cargo, which may be the subject of separate regulations. It refers to normal and fault conditions occur-ring in categories of equipment in five types of environment. The standard should also be read in conjunc-tion with British Standard 3C. 100: Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Explosion-proofness

3G 100 Pt.2 Sec.2-1972 航空用设备的一般要求规范.第2部分:各种设备.第2节:磁效应

Specificaton for general requirements for equipment in aircraft. All equipment. Magnetic influence

BS 3G 100-2.3.9:1972 飞机设备的一般要求规范.第2部分:各种设备.第3节:环境条件.结冰

This British Standard defines tests to evaluate the effect of various icing conditions on the performance of components or equipment in aircraft. Tt should be read in conjunction with British Standard 3G. 100 : Part 0. Three different tests are given, each of which has a specific field of application. The relevant equipment speci-fication will prescribe which test is to be used and also the appropriate functional checks.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Ice formation

BS 3G 100-2.3.8:1972 飞机设备一般要求规范.各种设备.环境条件.盐雾

This British Standard gives details of salt mist tests for two grades of severity, which may be applied to equipment in aircraft to determine their resistance to the corrosive effects of salt-laden atmospheres that exist at sea. in coastal areas and in certain desert areas. It should also be read in conjunction with British Standard 3G. 100: Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Salt mist

BS 3G 100-2.3.0:1972 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.标准试验要求

This British Standard specifies general require-ments for the environmental tests comprising the numerous subsections of British Standard 3G.100: Part 2: Section 3, including the test chamber, mounting of equipment in the test chamber, supplies to the chamber and standard reference conditions. It should be read in conjunction with British Standard 3G. 100: Part 0, and the relevant subsections.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Standard test requirements

BS 3G 100-2.3.7:1972 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.酷热曝露

This British Standard specifies a test to determine the suitability of equipment to be installed in air-craft that will be exposed to a humid environment typical of the tropically wet areas of the world. It should also be read in conjunction with British Standard 3G. 100: Part 0.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Tropical exposure

BS 3G 100-2.3.3:1972 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.长霉

This subsection of 3G. 100: Part 2 gives details of mould growth tests to be applied to materials and components used in aircraft equipment to determine that they are inherently resistant to mould growth. It should also be read in conjunction with British Standard 3G. 100: Part O.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Mould growth

BS 3G 100-2.3.4:1972 飞机设备一般要求规范.各种设备.环境条件.压差要求

This subsection of 3G.100: Part 2 describes tests to evaluate the effects of various pressure differential effects upon components or equipment used in aircraft. It should also be read in conjunction with British Standard 3G.100: Part 0. Three different tests are stated each of which has a specific field of application. The relevant equipment specification will prescribe the test(s) to be used and also the appropriate functional checks.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Differential pressure requirements

BS 3G 100-2.3.2:1970 飞机设备一般要求规范.各种设备.环境条件.温度压力要求

This subsection of 3G.100 Part 2 specifies climatic design and test requirements in addition to providing guidance in the test procedures for those responsible for the formu-lation of the climatic requirements clauses that will appear in detailed equipment design or requirement specifications. It is intended that this document will permit the selection of specific test conditions and methods that will unambigu-ously define the climatic acceptance requirements for specific equipment in aircraft.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Temperature-pressure requirements

BS 3G 100-2.3.1:1969 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.第1小节:振动

This subsection of 3 G.100: Part 2 relates to tests for complete units of airframe equipment subjected to aircraft vibration.

Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Vibration