V35 航空器及其附件综合 标准查询与下载

NAVY MS33558 REV C-1968 航空器仪表标度盘数字和字母的标准形式

NUMERAL AND LETTER, AIRCRAFT INSTRUMENT DIAL, STANDARD FORM OF

NUMERAL AND LETTER, AIRCRAFT INSTRUMENT DIAL, STANDARD FORM OF

BS 2G 135:1967 电加热皮托管和皮托静压管规范

1 This British Standard specifies the requirements for two grades of electrically-heated pitot and pitotstatic heads for aircraft. Grade A, heads fully de-iced and suitable for high speeds. Grade B, heads not suitable for flight in severe icing conditions. 2 Grade A comprises two classes of head: Class 1, heads not compensated for pressure error. Class 2, heads compensated for pressure error. 3 Grade B heads will normally be of the non-compensated type.

Specification for electrically-heated pitot and pitotstatic pressure heads

NAVY MS18054 REV B-1965 航空器用,5,8和10英寸同轴电动驱动垫块

DRIVE PADS FOR AIRCRAFT ELECTRIC EQUIPMENT CIRCULAR, 5, 8 AND 10 INCH

DRIVE PADS FOR AIRCRAFT ELECTRIC EQUIPMENT CIRCULAR, 5, 8 AND 10 INCH

NAVY MS18037 REV C-1964 直流线性航空器电动执行器

ACTUATOR, AIRCRAFT, ELECTRO-MECHANICAL, LINEAR, DIRECT CURRENT

ACTUATOR, AIRCRAFT, ELECTRO-MECHANICAL, LINEAR, DIRECT CURRENT

SAE AS127D-1963 法兰连接型螺旋桨轴.(1、2、3、4、5 & 6)

Propeller Shaft End, Flanged Type-No. 1, 2, 3, 4, 5,& 6

Propeller Shaft End, Flanged Type-No. 1, 2, 3, 4, 5,& 6

DLA MIL-F-25173 A (2)-1959 航空器装置控制面板扣件

This ammuhent formaa part of MilitarySpecification MIL-F-Z5173A(ASO),16 February1956,and has been apprOvedby the Departmentof the Air Force and by the Navy Bureauof AeronautIce.

FASTENER, CONTROL PANEL, AIRCRAFT EQUIPMENT

NAVY MS26551-1958 重油供应2.5英寸启动器

Provided by IHSNot for ResaleNo reproduction or networking permitted without license from HIS

STRAINER, 2.5 INCH PRESSURE FUEL SERVICING

DLA MIL-F-8490 A-1958 航空器支架系统弹药箱扣件

This specification covers the detail requirements for one tyix of fastener used on cases for the equipment-rack system in aircraft.

FASTENER, CASE, FOR EQUIPMENT RACK SYSTEM IN AIRCRAFT

DLA MIL-F-25173 A-1956 航空器装置控制面板扣件

w.9 SP9CifmIti0n COW- Om tsm Of CCQI-1 P-Q f----

FASTENER, CONTROL PANEL, AIRCRAFT EQUIPMENT

NF L87-122:1955 桨毂.前锥

Propeller hubs. Front cones.

NF L87-110:1955 平纹传动轴. 总成和标称尺寸.

Plain propeller shaft. Assembly and nominal dimensions.

NF L87-120:1955 普通螺旋桨轴.互换性.

Plain propeller shaft. Interchangeability characteristics.

NF L87-125:1955 桨毂.紧固螺母

Propeller hubs. Locknuts.

NF L87-123:1955 桨毂.尾锥

Propeller hubs. Rear cones.

NF L92-320:1943 螺旋浆组件用吊环的位置

Location of lifting eyes for propeller assemblies.

HB/Z 336-1999 飞机引气系统载荷分析方法

本标准规定了飞机引气系统载荷分析的方法和要求。 　　本标准适用于装有涡轮风扇、涡轮喷气、涡轮螺桨发动机的各类飞机的引气系统。

Load Analysis Method of Aircraft Bleed Air System

HB/Z 324-1998 运输类飞机重量与平衡设计

本标准规定了运输类飞机商载、空机重量定义与平衡设计要求。 　　本标准适用于ＣＣＡＲ２５部运输类飞机。其它民用飞机可参照使用。

Transport category aircraft weight and balance design

HB/Z 323-1998 飞行推力测量不确定度分析技术指南

本指南规定了航空涡轮喷气和涡轮风扇发动机及其相应的推进系统飞行推力测量不确定度分析的方法和程序。 　　本指南适用于确定以航空涡轮喷气和涡轮风扇发动机为动力的推进系统的飞行推力测量的A类不确定度。

Technical guide for flight thrust measurement uncertainty analysis

HB/Z 321-1998 飞机增升装置设计指南

本标准规定了军用飞机机械式增升装置的空气动力设计要求。 　　本标准适用于军用飞机，民用飞机亦可参照使用。

Aircraft High Lift Device Design Guidelines

HB/Z 298-1997 民用飞机航空电子设备设计指南

本标准规定了民用飞机航空电子设备（以下简称航空电子设备）互换性、安装、硬件和软件设计以及设备测试等方面的要求。 　　本标准适用于数字式航空电子设备，包括系统、分系统、设备和ＬＲＵ（Ｌｉｎｅ　Ｒｅｐｌａｃｅａｂｌｅ　Ｕ-ｎｉｔ，外场可更换单元）。在应用本标准时，可根据具体情况对其内容进行剪裁，以满足特定飞机对航空电子设备的特殊要求。

Civil Aircraft Avionics Design Guidelines