共找到 351 条与 燃油系统及其附件 相关的标准,共 24 页
This specification covers the requirements for aircraft fuel, vent, and propulsion system functional components.
FUEL SYSTEM COMPONENTS: GENERAL SPECIFICATION FOR
This Notice forms a part of Military Specification MIL-P-17689 (Nord), dated 30 July 1953, and shall constitute the cover page of the specification.
PROPELLANT, DOUBLE-BASE SHEET, TYPE N-5
This Specification covers propellant for use in amunition for the 20MM Naval Aircraft Guns, MARK 11 and MARK 12.
PROPELLANT FOR 20MM AMMUNITION
This amenb”t forms . part of Hilitary Specification 111L-v-24332 (SHIPS) , 1 July 1968 and is approved for .s. by all Department. and agencies of the Department of Defease.
VALVES, ANGLE RELIEF, FOR LIQUID SERVICE (NAVAL SHIPBOARD)
This specification is approved for use by all Departments and Agencies of the Department of Defense.
CASTING SOLVENT FOR OIA, OGK AND AHH PROPELLANTS
This specification covers the requirements for a blue and white summer coat fabricated from a polyester fiber-cotton cord fabric
COAT, WOMAN'S, SUMMER (NAVY)
Mounting interchangeability. Flanges for reinforced tanks. (ISO thread profile and tolerances).
This specification covers propellant increments made from M8 Propellant, for use in Charge, Propelling, M36A2 for 4.2 Inch Ammunition.
INCREMENTS, PROPELLANT FOR CHARGE, PROPELLING, M36A2 (MADE FROM PROPELLANT M8)
This amendment forms a part of Military Specification lIL-V-20065D(SIIIPS), 8 June 1967
VALVES, ANGLE, PRESSURE RELIEF, NAVAL SHIPBOARD, FOR STEAM SERVICE
FLAGS, ORGANIZATIONAL: STANDARDS, USMC
FLAGS, ORGANIZATIONAL: STANDARDS, USMC
This amendment forms a part of Military Specification MlL-P-l8942A(NOrd) dated 18 December 1956 and has been approved for use by the Naval Ordnance Systems Command, Department of Navy.
PROPELLANT FOR 20MM ANTI-AIRCRAFT GUN MARK 12
TURBINE, STEAM AND REDUCTION GEAR, AUXILIARY, GENERATOR-DRIVE (NAVAL SHIPBOARD USE)
TURBINE, STEAM AND REDUCTION GEAR, AUXILIARY, GENERATOR-DRIVE (NAVAL SHIPBOARD USE)
This speck-icatior covers a cherAcal proportioning unit consisting of a motor drLven, positLve displaceKent reciprocating typs punp rith attached liquid supply tznk for Ese witin shipboard distilìing plants.
PROPORTIONING UNIT, CHEMICAL (FOR DISTILLING PLANTS NAVAL SHIPBOARD USE)
This specification covers the design and construction of vacuum pumps for the purpose of priming centrifugal pumps by removing a I r and associated vapors from pump casings and suction piping.
VACUUM PUMPS, POWER DRIVEN, CENTRIFUGAL PUMP PRIMING SERVICE, NAVAL SHIPBOARD
This specific tion covers the requirements for spun type marine oakum.
OAKUM, MARINE
This specification covers- five propeilant increments made from M8 propellant for use in mortar'ammunition.
INCREMENTS, PROPELLANT M1A1, M2A1, M3A1, M181 AND M182 (MADE FROM PROPELLANT, M8)
This specification covers propellant increments made from M8 Propellant for use in charge, propelline; M36A1 for 4.2 Inch Mortar Cannon M30.
MILITARY SPECIFICATION INCREMENTS, PROPELLANT FOR CHARGE, PROPELLING, M36A1 (MADE FROM PROPELLANT, M8)
This specification covers angle relief valves of pressure tight spring housing construction for gas and oxygen service.
VALVES, ANGLE, RELIEF, FOR GAS AND OXYGEN SERVICE (SIZES 2-INCHES IPS AND BELOW); NAVAL SHIPBOARD
This specification covers spring loaded leli~f val Te% of totnlly enclczed spring pressure tight construction for liquid service (except hydraulic oil) .
VALVES, ANGLE RELIEF, FOR LIQUID SERVICE (NAVAL SHIPBOARD)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号