共找到 444 条与 航天器综合 相关的标准,共 30 页
This specification covers instruments known as Mount,Periscope: Mi18 and Mo?nt, Periscope: Ml18E1(see 6.1).
MOUNT, PERISCOPE: M118 AND M118E1
This amendment forms a part of Military Specification MIL-G-45140B, dated 12 October 1976, and is approved for use by all Departments and Agencies of the Department of Defense.
MINES, LAND, PRACTICE AND LAND MINE SIMULATORS, COLOR OF INDICATING SMOKE FOR
This specification covers one type of instrument designated Mount, Periscope: Ml.15.
MOUNT, PERISCOPE: M115
This specification covers Remover, Aircraft Canopy, M8A1 Remanufacture Metal Parts Assembly and modification requirements to incorporate the new load limiting device in the gear box assembly. Be loaded and used in conjunction with other propellant actuated devices in aircrew emergency escape systems.
REMOVE, AIRCRAFT CANOPY, M8A1 REMANUFACTURED METAL PARTS ASSEMBLY
This specification covers requirements and quality assurance provisions for obturating band, plastic, split(molded) for use on the Cartridge, 81mm; Illuminating, M853; Smoke, RP, M819 and Practice, M879.
CASE, BINOCULAR, M62A1 AND M64A1
This specification covers the general rzequirements of NAVAIR (Naval Air Systems Camand) for the demonstration of helicopters. These general requirements w i l l be m o d i f i e d and amplified as required by contract addenda to this specification. The expression "demonstration" refers to all of the contractor's work (as applied to specific helicopter models and contracts) specified herein including modifications and amplifications contained in pertinent contractual documents. fied requirements may l i m i t the demonstration for a particular contract or helicopter model to only a limited number of tests to be performed at a single location and, also, may contain requirements for the demonstration of features and characteristics not included in this general specification.
DEMONSTRATION REQUIREMENTS FOR HELICOPTERS
This specification covers a periscope mount which is provided with an electrically operated wiper blade for wiping the periscope entrance window(see 6.1).
MOUNT, PERISCOPE: 10513360
This amendment forms a part of Military Specification MIL-M-45659C(Mü) , dated 11 May 1964.
MOUNT, TELESCOPE: M110
This specification covers one type of instrument known as Mount, Periscope, Ml19(see 6.1).
MOUNT, PERISCOPE: M119
This specification covers one type of rubber frame goggles with plastic lens inserts,
GOGGLES, SUN, WIND AND DUST
1.1 This practice provides application criteria, definitions, and supplemental information to assist the user in obtaining meaningful vacuum ionization gage measurements below 101 N/m2 (10 3 torr) in space-simulation facilities. Since a variety of influences can alter observed vacuum measurements, means of identifying and assessing potential problem areas receive considerable attention. This practice must be considered informational, for it is impossible to specify a means of applying the vacuum-measuring equipment to guarantee accuracy of the observed vacuum measurement. Therefore, the user''s judgment is essential so that if a problem area is identified, suitable steps can be taken to either minimize the effect, correct the observed readings as appropriate, or note the possible error in the observation.1.2 While much of the discussion is concerned with the application of hot-cathode ionization gages, no exclusion is made of cold-cathode designs. Since a great deal more experience with hot-cathode gages is available and hot-cathode devices are used in the majority of applications, the present emphasis is fully warranted.1.3 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.
Standard Practice for Ionization Gage Application to Space Simulators
I. FOR QENERAL PALLETIZINQ REQUIREMENTS SEE MIL-STO-I322 (NAVY). 2. UNLESS OTHERWISE SPECIFIEO DIMENSIONS ARE IN INCHES.
PALLETIZING DOMESTIC UNIT LOAD 20 MM AIRCRAFT AND SMALL ARMS AMMUNITION (IN SMALL ARMS AMMO BOX MK 1 MOD 0)
Photosensitive Anodized Aluminum Markings: Plates and Foil, Photographic, Standard for
Photosensitive Anodized Aluminum Markings: Plates and Foil, Photographic
This specification covers the requirements for two types of emergency signaling mirrors, designated as Mark 3.
MIRRORS, EMERGENCY SIGNALING, MARK 3
Materials, parts and assemblies shall comply with the requirements specified in T.O. llP4-11-3, and referenced specifications and standards.
REMOVER, AIRCRAFT CANOPY, P/N 2218-18 OVERHAUL OF
Materials, parts and sssemblfes shall conform to the appli-cable drawings an. Referenced specifications.
HOLDER, STRIP, LOADED, ASSEMBLY MB, M9, M10, XM12, M19 OR XM25 AIRCRAFT EJECTION SEAT CATAPULT
The equipment covered by this apecification shall The stations shall meet the requirements for use in high provide e f f h i e n t intercommunications and receiver audio output combinbng and isolating functions. performance a i r c r a f t where space, weight, and input power are at a premium,
INTERCOMMUNICATION STATIONS LS-459(*)/AIC AND LS-460(*)/AIC
This specification covers one protective mask eyelens outsert.
OUTSERT, EYELENS, M1 [Use In Lieu Of: ARMY MIL-O-0050077 F CANC NOTICE 1]
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号