X85 制烟综合 标准查询与下载

YC/T 169.5-2009 烟用丝束理化性能的测定.第5部分:断裂强度

YC/T 169的本部分规定了烟用丝束断裂强度的测定方法。 本部分适用于烟用二醋酸纤维素丝束。

Determination of physical and chemical characteristics of tow for cigarette.Part 5:Breaking strength

YC/T 169.7-2009 烟用丝束理化性能的测定.第7部分:回潮率

YC/T 169的本部分规定了烟用丝束回潮率的测定方法。 本部分适用于烟用聚丙烯纤维丝束。

Determination of physical and chemical characteristics of tow for cigarette.Part 7:Moisture regain

YC/T 169.6-2009 烟用丝束理化性能的测定.第6部分:截面形状和径向异形度

YC/T 169的本部分规定了烟用丝束截面形状和径向异形度的测定方法。 本部分适用于烟用二醋酸纤维素丝束和烟用聚丙烯纤维丝束。

Determination of physical and chemical characteristics of tow for cigarette.Part 6:Outline of cross section and shape factor in radius

YC/T 169.3-2009 烟用丝束理化性能的测定.第3部分:卷曲数

YC/T 169的本部分规定了烟用丝束卷曲数的测定方法。 本部分适用于烟用二醋酸纤维素丝束和烟用聚丙烯纤维丝束。

Determination of physical and chemical characteristics of tow for cigarette.Part 3:Crimp number

YC/T 169.2-2009 烟用丝束理化性能的测定.第2部分:单丝线密度

YC/T 169的本部分规定了烟用丝束单丝线密度的测定方法。 本部分适用于烟用二醋酸纤维素丝束和烟用聚丙烯纤维丝束。

Determination of physical and chemical characteristics of tow for cigarette.Part 2:Linear density of filament

YC/T 169.1-2009 烟用丝束理化性能的测定.第1部分:丝束线密度

YC/T 169的本部分规定了烟用丝束线密度的测定方法。 本部分适用于烟用二醋酸纤维素丝束和烟用聚丙烯纤维丝束。

Determination of physical and chemical characteristics of tow for cigarette.Part 1:Total line density

YC/T 294-2009 烟用香精和料液中砷、铅、镉、铬、镍的测定.石墨炉原子吸收光谱法

本标准规定了烟用香精和料液中砷、铅、镉、铬、镍的测定方法－石墨炉原子吸收光谱法。 本标准适用于烟用香精和料液中砷、铅、镉、铬、镍的测定。

Determination of arsenic,lead,cadmium,chromium and nickel in tobacco flavourings and castings.Graphite furnace atomic absorption spectrometry

YC/T 293-2009 烟用香精和料液中汞的测定.冷原子吸收光谱法

本标准规定了烟用香精和料液中汞的测定方法－冷原子吸收光谱法。 本标准适用于烟用香精和料液中汞的测定。

Determination of mercury in tobacco flavourings and castings.Cold atomic absorption spectrometry

YC 292-2009 烟草添加剂.枣子提取物

本标准规定了烟草添加剂枣子提取物的术语和定义、分类、技术要求、试验方法、检验规则和包装、标识、运输和贮存。 本标准适用于作为烟草添加剂使用的枣子提取物。

Tobacco additive.Red date extracts

YC/T 289-2009 卷烟.配方烟丝结构的测定

本标准规定了卷烟配方烟丝结构的测定方法。 本标准适用于各种卷烟配方烟丝结构的测定。

Cigarette.Determination of structure of blending cut tobacco

NF V37-050:2009 卷烟.卷烟主流烟雾中苯并芘的测定.气相色谱/质谱方法

Cigarettes - Determination of benzo(a)pyrene in cigarette mainstream smoke - Method using gas chromatography/mass spectrometry.

NF V37-043-3*NF ISO 15592-3:2009 细切烟草及其烟制品.抽样、检验和分析用方法.第3部分:用常规分析吸烟机测定烟制品中颗粒物质总量、水和烟碱测定的准备及无烟碱干燥颗粒物质的计算

Fine-cut tobacco and smoking articles made from it - Methods of sampling, conditioning and analysis - Part 3 : determination of total particulate matter of smoking articles using a routine analytical smoking machine, preparation for the determination of w

DIN ISO 8243:2009 卷烟.取样

This International Standard specifies two methods of providing representative samples of a population of cigarettes manufactured for sale. Different procedures are specified (see Table 1) according to whether sampling is undertaken at the point of sale or at a factory. a) Sampling "at one point in time" provides for appraisal of the chosen properties of the cigarettes on that occasion. Sampling is carried out within as short a period as possible. b) Sampling "over a period of time" provides for on-going appraisals. It can be considered for practical purposes as a series of samples each taken "at one point in time". This International Standard provides information on the statistical basis for the treatment of data and gives estimates, based on practical experience, of the typical confidence intervals for NFDPM, nicotine and CO yields which may be found when a product is sampled in accordance with this International Standard and smoked in accordance with the procedures specified in ISO 3308, ISO 3402, ISO 4387, ISO 8454, ISO 10315, ISO 10362-1 and ISO 10362-2.

Cigarettes - Sampling (ISO 8243:2006)

ASTM E2187-09 测量香烟引火强度的标准试验方法

The most common initiating event in a fatal fire is the dropping of a cigarette onto a bed or piece of upholstered furniture, causing 20 % of the estimated U.S. fire deaths from 1992–1996 in residential structures, according to statistics provided by the U.S. Consumer Product Safety Commission. Test Methods E1352 and E1353 have been developed to evaluate the susceptibility of upholstered furniture mock-ups and components to ignition by cigarettes. Federal Standard 16 CFR Part 1632, Standard for the Flammability of Mattresses and Mattress Pads, was promulgated to reduce the likelihood that mattresses and mattress pads would ignite from a lighted cigarette. This test method enables comparison of the relative ignition strength of different cigarette designs. In this procedure, the specimens are subjected to a set of laboratory conditions. If different conditions are substituted or the end use conditions are changed, it may not be possible, using this test, to predict quantitative changes in the fire test response characteristics measured. Therefore, the quantitative results are valid only for the fire test exposure conditions described in this procedure.1.1 This fire-test-response standard provides a standard measure of the capability of a cigarette, positioned on one of three standard substrates, to generate sufficient heat to continue burning and thus potentially cause ignition of bedding or upholstered furniture. 1.2 This method has value as a predictor of the relative propensity of a cigarette to ignite upholstered furnishings. 1.3 This method is applicable to cigarettes that burn along the length of a tobacco column. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.

Standard Test Method for Measuring the Ignition Strength of Cigarettes

YC/T 276-2008 烟用材料供应企业质量信用等级评价体系

本标准规定了烟用材料供应企业质量信用等级评价体系的构成要素、测度指标、数据采集及等级水平。 本标准适用于对烟用材料供应企业质量信用等级的评价,也可供烟用材料供应企业进行自我评价。

System for evaluation of cigarette materials quality credibility

YC/T 273-2008 卷烟包装设计要求

本标准规定了卷烟包装设计总体要求、包装材质要求、包装结构要求、包装造型要求、包装装潢要求以及包装成本控制要求。 本标准适用于市场销售卷烟的包装及包装设计活动。

Requirements for design of cigarette package

ISO 22634:2008 卷烟.卷烟主流烟雾中苯并芘的测定.气相色谱/质谱方法

This International Standard specifies a method for the determination of benzo[a]pyrene (B[a]P) in the total particulate matter of cigarette mainstream smoke. This method is specified using ISO 3308 smoking parameters, but is technically compatible with other smoking regimes.

Cigarettes - Determination of benzo[a]pyrene in cigarette mainstream smoke - Method using gas chromatography/mass spectrometry

DB53/ 56-2008 烤烟标准实物标样制作审定技术规程

本标准规定了烤烟标准实物标样制作的原料选留、保管、整理、配把、扎把及实物标样的审定、签封、装箱、供应等技术要求。本标准适用于烤烟标准实物标样的制作及审定。

Technical regulations for making standard samples of flue-cured tobacco

DB53/T 65-2008 烤烟分级扎把技术规范

本标准规定了烟叶初烤后的处理、堆放、分级、扎把、保存等技术要求。本标准适用于初烤烟的分级扎把。

Technical specification for grading and binding of flue-cured tobacco

KS H ISO 7210:2008 卷烟的常规分析.吸烟机.补充试验方法

이 표준은 일상 분석용 자동흡연장치들이 KS H ISO 3308과 잘 일치하는지를 체크하기

Routine analytical cigarette-smoking machine-Additional test methods