Y14 自行车 标准查询与下载

JIS T 9201 ERRATUM 1:2008 勘误表

ERRATUM

JIS T 9203 ERRATUM 1:2008 勘误表

ERRATUM

DIN EN 1888 Berichtigung 1:2008 儿童保健用品.轮式儿童车辆.安全要求和试验方法.德国版EN 1888-2003＋A1:2005＋A2:2005＋A3:2005.技术勘误DIN EN 1888-2005-11

Child care articles - Wheeled child conveyances - Safety requirements and test methods; German version EN 1888:2003 + A1:2005 + A2:2005 + A3:2005, Corrigendum to DIN EN 1888:2005-11

ISO 7176-19:2008 轮椅.第19部分:用作汽车座椅的有轮易动性装置

This part of ISO 7176 applies to all manual and powered wheelchairs, including scooters, which, in addition to their primary function as wheeled mobility devices, are also likely to be used as forward-facing seats in motor vehicles by children and adults with a body mass equal to or greater than 22 kg. This part of ISO 7176 specifies wheelchair design requirements, performance requirements and associated test methods, and requirements for wheelchair labelling, presale literature, user instructions and user warnings. It applies to complete wheelchairs, including a base frame and seating system, as well as to wheelchairs equipped with add-on adaptive components designed to facilitate compliance with one or more of the requirements.

Wheelchairs - Part 19: Wheeled mobility devices for use as seats in motor vehicles

BS ISO 7176-14:2008 轮椅.电动轮椅和小型摩托车的动力和控制系统.要求和试验方法

Wheelchairs - Power and control systems for electrically powered wheelchairs and scooters - Requirements and test methods

QB 1880-2008 自行车.车架

本标准规定了自行车车架（以下简称“车架”）的术语和定义、产品分类、技术要求、检验规则和标志、包装、运输、贮存。 本标准适用于QB 1714中规定的一般用途的普通自行车、载重自行车、轻便自行车、运动自行车和电动自行车用车架。

Front forks for bicycles

QB/T 1881-2008 自行车 前叉

Bicycle front fork

QB/T 1880-2008 自行车 车架

Bicycle frame

QB 1881-2008 自行车.前叉

本标准规定了自行车前叉（以下简称“前叉”）的产品分类、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于QB 1714中规定的一般用途的普通自行车、载重自行车、轻便自行车、运动自行车和电动自行车用前叉。 本标准不适用于其他特殊用途自行车前叉。

Front forks for bicycles

ISO 7176-5:2008 轮椅.第5部分:轮廓尺寸、体积和操纵空间的测定

This part of ISO 7176 specifies methods for the determination of wheelchair dimensions and mass, This includes specific methods for the determination of outside dimensions when the wheelchair is occupied by a reference occupant and the required manoeuvring space needed for wheelchair manoeuvres commonly carried out in daily life. This part of ISO 7176 specifies requirements for the disclosure of the dimensions and masses and contains five informative annexes. AnnexA specifies methods for the determination of technical dimensions that can be important to the performance of the wheelchair. Annex B provides detailed information about pivot width and reversing width. Annex C provides detailed information about the turning diameter. Annex D provides details on determining the wheelchair longitudinal axis and wheelchair centre-point. Annex E provides technical guidelines and recommendations for many of the measurements specified to facilitate improved understanding, design and construction of wheelchairs. This Dart of ISO 7176 is applicable to manual wheelchairs and electricallv Dowered wheelchairs (including scooters).

Wheelchairs - Part 5: Determination of dimensions, mass and manoeuvring space

DIN EN 14765:2008 儿童自行车.安全要求和试验方法

This European Standard specifies safety and performance requirements and test methods for bicycles for young children, in respect of the design, assembly and testing of bicycles and sub-assemblies. Guidelines for instructions on the use and care of bicycles are also provided. This European Standard applies to bicycles with a maximum saddle height of more than 435 mm and less than 635 mm (typical rider weight of 30 kg), and propelled by a transmitted drive to the rear wheel. This European Standard does not apply to special bicycles intended for stunting (e.g. BMX bicycles). NOTE For bicycles with a maximum saddle height of 435 mm see EN 71 and for bicycles with a saddle height of 635 mm or more see prEN 14764.

Bicycles for young children - Safety requirements and test methods (includes Amendment A1:2008); English version of DIN EN 14765:2008-062

JIS T 9207:2008 轮椅用便携式车轮坡道

This Japanese Industrial Standard specifies the portable ramps (hereafter referred to as "ramps") to be set on stairs, steps or the area where a gap exists to make it pos- sible to pass through by supporting the load with both ends for manually propelled wheelchairs or electric wheelchairs. Ramps fixed by claws, etc. shall be excluded.

Portable ramps for wheelchairs

NF R30-006/IN1:2008 幼童用自行车.安全要求和试验方法

Bicycles for young children - Safety requirements and test methods.

NF R30-006:2008 幼童用自行车.安全要求和试验方法

Bicycles for young children - Safety requirements and test methods.

ANSI/ASTM F2711:2008 自行车架用试验方法

Test Methods for Bicycle Frames

JIS D 9302:2008 儿童自行车

This Standard specifies bicycles for young children defined in JIS D 9111 (hereaf- ter referred to as "bicycles"). NOTE: The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 8098:2002 Cycles-Safety requirements for bicycles for young children (MOD) The symbols which denote the degree of correspondence in the contents between JIS and the corresponding International Standard are IDT (iden- ticalt, MOD (modified) and NEQ (not equivalent) according to ISO/IEC Guide 21.

Bicycles for young children

JIS D 9301:2008 普通自行车

This Standard specifies general specification of bicycles for general use (hereafter referred to as "bicycles") defined in JIS D 9111. Those bicycles with electric assist- ing.mechanism i.e. electric power assist bicycles are excluded from the scope of this Standard. Bicycles for general use refer to sports bicycle, city cycle, utility bicycle and chil- dren bicycle, and the folding or separable type bicycle is included. NOTE : The International Standard corresponding to this Standard and the symbol of degree of correspondence is as follows. ISO 4210 : 1996 Cycles-Safety requirements for bicycles (MOD) The symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21

Bicycles for general use

NF R30-013*NF EN 15496:2008 自行车.自行车锁的要求和试验方法

Cycles - Requirements and test methods for cycle locks.

DIN EN 15496:2008 自行车.自行车车锁的要求和试验方法

This European Standard specifies performance requirements and describes test methods for strength, security, function and corrosion resistance of locks for cycles. It also covers certain aspects regarding the safety of the rider of the cycle on which the lock is mounted. This standard covers permanently-mounted cycle locks and removable locks.

Cycles - Requirements and test methods for cycle locks; English version of DIN EN 15496:2008-04

JIS D 9455:2008 自行车用气筒

この規格は，AS D 9111に規定する自転車に用いる空気ポンプ(以下，ポンプという。)について規定する。ただし，電動式の空気ポンプには適用Lない。

Air pumps for bicycles