Y14 自行车 标准查询与下载

JIS D 9415:2008 自行车.链轮和曲柄

この規格は，主にJIS D 9111に規定する一般用自転車及び幼異黒負転車に用いるギャクランク(以下，ギヤクランクという。)について規定する。

Bicycles -- Chainwheels and cranks

JIS D 9418:2008 自行车.飞轮及小齿轮

この規格は，キにJIS D 9111に規定する一般用自転車及び幼児用自転車に用いるフリーホイール及び小ギヤについて規定する。

Bicycles -- Free wheels and hub cogs

JIS D 9414:2008 自行车.闸

This Japanese Industrial Standard specifies the brake assemblies used for bicycles for general use and for bicycles for young children specified in JIS D 9111.

Bicycles -- Brakes

BS EN 15496:2008 自行车.自行车车锁的要求和试验方法

This European Standard specifies performance requirements and describes test methods for strength, security, function and corrosion resistance of locks for cycles. It also covers certain aspects regarding the safety of the rider of the cycle on which the lock is mounted. This standard covers permanently-mounted cycle locks and removable locks.

Cycles - Requirements and test methods for cycle locks

QB/T 2946-2008 电动自行车用电动机及控制器

本标准规定了电动自动车（包括含减速器的电动机）及控制器的型号命名、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于电动自行车电动机（以下简称“电动机”）及控制器。

Motor and controller used for electric bicycles

ISO 7176-14:2008 轮椅.第14部分:电动轮椅和单脚滑行车的电力控制系统.要求和试验方法

This part of ISO 7176 specifies requirements and associated test methods for the power and control systems of electrically powered wheelchairs and scooters. It sets safety and performance requirements that apply during normal use and some conditions of abuse and failure. It also specifies methods of measurement of the forces necessary to operate controls and sets limits on the forces needed for some operations. This part of ISO 7176 is applicable to electrically powered wheelchairs and scooters with a maximum speed no greater than 15 km/h intended to provide indoor and/or outdoor mobility for one disabled person whose mass lies in the range specified in ISO 7176-11.

Wheelchairs - Part 14: Power and control systems for electrically powered wheelchairs and scooters - Requirements and test methods

ASTM F2641-08 娱乐电动滑板车和折叠自行车安全的消费者安全标准规范

1.1 This consumer safety specification covers the establishment of performance requirements and corresponding test methods used to minimize the hazards to users of recreational powered scooters and pocket bikes. 1.2 This specification is intended to cover use of these products for children: 1.2.1 Age eight to twelve for units limited to speeds 16 km/h (10 miles/h) or less. 1.2.2 Age 13 and above for fast-moving units capable of achieving speeds >16 km/h (>10 miles/h). 1.3 This consumer safety specification is not intended for units designed or licensed for roadway use regulated by transportation regulations (Department of Transportation (DOT) or state). 1.4 This specification is not intended for units designed and sold as “Adult Use Only” and are prominently labeled and marked as such. 1.5 This consumer safety specification is not intended for nonpowered scooters (Consumer Safety Specification F 2264), battery powered ride-on toys (Consumer Safety Specification F 963), skateboards, motorcycles, all-terrain vehicles, go-carts (Practice F 2007), fun-karts (Specification F 2011), snowmobiles, motorized trail bikes, lawnmowers, or motorized wheelchairs including mobility scooters. 1.6 No product covered by this specification produced after the approval date of this consumer safety specification shall, by label, marking, or other means, indicate compliance with this consumer safety specification unless it conforms to all requirements herein. 1.7 The values given in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Recreational Powered Scooters and Pocket Bikes

ASTM F2642-08 动力休闲滑板车和迷你自行车的安全说明和标示的标准消费者安全规范

1.1 This consumer safety specification includes requirements for safe-use instructions and labeling to minimize the hazards to users of recreational powered scooters and pocket bikes. This specification is intended to cover safety instructions, labeling, and maintenance for products for: 1.1.1 Children age eight to twelve for units limited to speeds 16 km/h (10 miles/h) or less, and 1.1.2 Children age 13 and above for fast-moving units capable of achieving speeds of >16 km/h (>10 miles/h). 1.2 This specification is intended to reduce hazards, other than those inherent to the users of these units during normal intended use and within manufacturers’ safety guidelines. 1.3 This specification is not intended for non powered scooters (Consumer Safety Specification F 2264), battery powered ride-on toys (Consumer Safety Specification F 963), motorcycles, skateboards, all terrain vehicles (ATVs), go-karts (Practice F 2007), fun-karts (Safety Guide F 1928), snowmobiles, motorized trail bikes, lawn mowers, or motorized wheelchairs including mobility scooters. 1.4 This specification is not intended for units designed for “Adult Use Only” and that are prominently labeled and marked as such. 1.5 This specification is not intended for units designed or licensed for roadway use or regulated by transportation regulations (that is, Department of Transportation (DOT) or state). 1.6 The values given in SI units are to be considered as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Safety Instructions and Labeling for Recreational Powered Scooters and Pocket Bikes

ASTM F2711-08 自行车车架的标准试验方法

These tests are used to verify the durability and strength of a bicycle frame.1.1 These test methods establish procedures for conducting tests to determine the structural performance properties of bicycle frames. 1.2 These test methods describe mechanical tests for determining the following performance properties: 1.2.1 Frame Fatigue—Horizontal Loading, 1.2.2 Frame Fatigue—Vertical Loading, and 1.2.3 Frame Impact Strength. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Bicycle Frames

ANSI/ASTM F1898:2008 婴儿和儿童用自行车头盔的规范

Specification for Bicycle Helmets Used by Infants and Toddlers

SN/T 0248.1-2007 进出口自行车及其零件检验规程第1部分:通用要求

SN/T 0248的本部分规定了进出口自行车及其零件的抽样、检验、检验结果判定、检验后的处置和检验有效期。 本部分适用于进出口公路自行车及34种自行车零件的检验。

Rules for the inspection of bicycle and parts of bicycle for import and export.Part 1:General requirements

KS P ISO 7176-8:2007 轮椅.第8部分:静态强度、冲击强度和疲劳强度的要求和试验方法

이 규격은 휠체어의 정하중, 충격 강도, 피로 강도의 요구사항을 규정하는데, 휠체어의 범위

Wheelchairs－Part 8：Requirements and test methods for static, impact and fatigue strengths

KS P ISO 7176-1:2007 轮椅.第1部分:静态稳定性的测定

이 규격은 휠체어와 스쿠터의 쏠림 자세의 정적 안정성 결정 방법을 규정한다. 이 규격은 I

Wheelchairs－Part 1：Determination of static stability

BS ISO 16840-2:2007 轮椅座椅.维持组织完整性的装置物理和机械特性测定.座椅垫

This part of ISO 16840 specifies apparatus,test methods and disclosure requirements for wheelchair seat cushions intended to maintain tissue integrity and prevent tissue trauma.It does not include test methods or requirements for determining the fire resistance of cushions.Annex B provides guidance on selecting cushions with appropriate fire resistance characteristics.This part of ISO 16840 does not address the interface pressure distributing characteristics of seat cushions nor the heat and water vapour dissipation characteristics of seat cushions that will be addressed in further parts of ISO 16840. This part of ISO 16840 can also be applicable to tissue integrity management devices used as other support systems,as well as to cushions used in situations other than a wheelchair.

Wheelchair seating. Determination of physical and mechanical characteristics of devices intended to manage tissue integrity. Seat cushions

BS ISO 7176-26:2007 轮椅.词汇表

This part of ISO 7176 specifies a vocabulary consisting of terms and definitions used in the field of manual and electrically powered wheelchairs (including scooters) and associated seating systems. This part of ISO 7176 includes, but is not limited to, the preferred terms used in two or more ISO standards of the ISO 7176, ISO 10542, and ISO 16840 series, but does not include terms considered to be adequately defined in everyday English.

Wheelchairs. Vocabulary

ISO 16840-2:2007 轮椅座椅.第2部分:维持组织完整性的装置物理和机械特性测定

This part of ISO 16840 specifies apparatus,test methods and disclosure requirements for wheelchair seat cushions intended to maintain tissue integrity and prevent tissue trauma.It does not include test methods or requirements for determining the fire resistance of cushions.Annex B provides guidance on selecting cushions with appropriate fire resistance characteristics.This part of ISO 16840 does not address the interface pressure distributing characteristics of seat cushions nor the heat and water vapour dissipation characteristics of seat cushions that will be addressed in further parts of ISO 16840. This part of ISO 16840 can also be applicable to tissue integrity management devices used as other support systems,as well as to cushions used in situations other than a wheelchair.

Wheelchair seating - Part 2: Determination of physical and mechanical characteristics of devices intended to manage tissue integrity - Seat cushions

JIS T 9255:2007 辅助站立和坐下用的电动机制椅子和座椅

この規格は，座面を電動で昇降させることによって，立上がり及び着座動作を支援することを目的として設計したいす(以下，補助いすという。)について規定する。なお，人を乗せたまま運搬する目的のいす並びに便座用及び浴室用のいすは除く。

Chairs and seats with electrical mechanisms assist standing up and sitting down

JIS D 9432:2007 自行车.链调整器和曲柄扁销

この規格は，JIS A 9111に規定する一般用自転車及び幼児用自転車に用いるチェーン引き及びクランクピンについて規定する。

Bicycles -- Chain adjusters and crank cotter pins

JIS D 9454:2007 自行车.传动链壳体

この規格は，JIS D 9111に規定する一般用自転車及び幼児用自転車に用いるチェーンケース(以下，チエーンケースという。)について規定する。

Bicycles -- Chain cases

JIS D 9453:2007 自行车.载物架和支架

この規格は，主としてJIS D 9111に規定する一般用自転車及び幼児用自転車に用いるリヤキャリャ(以下，キャリャという。)及びスタンドについて規定する。

Bicycles -- Luggage carriers and stands