Y14 自行车 标准查询与下载

SN/T 0248.1-2003 进出口公路自行车安全检验规程

Rules for the safety requirements inspection of public road bicycles for import and export

ANSI/ASTM F2268:2003 自行车系列号规范

This standard specifies the format, content, number of characters and physical requirements for serial numbers to facilitate recall campaigns and identification of stolen property. This standard is applicable to all bicycles, refer to Classification F 2043 on definition for bicycle.

Specification for Bicycle Serial Numbers

ISO 7176-21:2003 轮椅.第21部分:电动轮椅和小型电动摩托车的电磁兼容性要求和试验方法

This part of ISO 7176 specifies requirements and test methods for electromagnetic emissions and for electromagnetic immunity of electrically powered wheelchairs and motorized scooters with a maximum speed of not more than 15 km/h for indoor and outdoor use by people with disabilities. It is also applicable to manual wheelchairs with an add-on power kit. It is not applicable to vehicles designed to carry more than one person. This part of ISO 7176 also specifies additional requirements for electromagnetic emissions and for electromagnetic immunity of electrically powered wheelchairs and motorized scooters with a built-in battery charger. It is not applicable to battery chargers that are not built into a wheelchair. A reference configuration is specified for adjustable wheelchairs and scooters to enable test results to be used for comparison of performance. NOTE The term "wheelchair" is used in this part of ISO 7176 to cover electrically powered wheelchairs, motorized scooters and manual wheelchairs with an add-on power kit.

Wheelchairs - Part 21: Requirements and test methods for electromagnetic compatibility of electrically powered wheelchairs and motorized scooters

ISO 7176-3:2003 轮椅.第3部分:制动器效能的测定

This part of ISO 7176 specifies test methods for the measurement of the effectiveness of brakes of manual wheelchairs and electrically powered wheelchairs, including scooters, intended to carry one person, with a maximum speed not exceeding 15 km/h. It also specifies disclosure requirements for the manufacturer.

Wheelchairs - Part 3: Determination of effectiveness of brakes

SN/T 0248.3-2003 进出口非公路自行车安全检验规程

本标准规定了进出口非公路自行车安全检验的抽样、检验、检验方法和检验结果判定以及检验后的 处置和检验有效期 。 本标准适用于非公路自行车的安全要求检验。

Rule for the safety requirements inspection of off-road bicycles for import and export

ASTM F977-03 婴儿学步车的用户安全使用标准规范

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of the infant walker (see 3.1).1.2 This consumer safety specification is intended to minimize accidents to children resulting from normal use and reasonably foreseeable misuse or abuse of walkers.1.3 No walker produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.1.4 This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of other persons with the child in the walker or the accidents resulting from abuse and misuse by children able to walk.1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Infant Walkers

ASTM F833-03 车及婴儿四轮车的使用者安全性能标准规范

1.1 This consumer safety specification establishes safety performance requirements, test methods, and requirements for labeling to minimize the hazards to children presented by carriages and strollers as identified in the introduction. 1.2 No carriage or stroller produced after the approval date of this consumer safety performance shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements herein. 1.3 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only. 1.4 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Performance Specification for Carriages and Strollers

ASTM F2273-03 自行车叉的标准试验方法

These tests are used to determine the performance of a bicycle fork.1.1 These test methods describe mechanical tests for determining the following performance properties:1.1.1 Compression Load,1.1.2 Bending Load,1.1.3 Impact Resistance, and1.1.4 Fatigue Life.1.2 The values stated in SI units are to be regarded as standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Bicycle Forks

ASTM F2268-03(2010) 自行车序列号标准规范

1.1 This standard specifies the format, content, number of characters and physical requirements for serial numbers to facilitate recall campaigns and identification of stolen property. 1.2 This standard is applicable to all bicycles, refer to Classification F2043 on definition for bicycle.

Standard Specification for Bicycle Serial Numbers

ASTM F2106-03 装有电动机的人力蹋车设计和性能特征评定的标准试验方法

The purpose of these test methods is to provide reliable and repeatable test methods for the evaluation of motorized treadmills assembled and maintained according to the manufacturerrsquo;specifications. Use of these test methods in conjunction with Specification F 2115 is intended to insure appropriate performance and reliability of a motorized treadmill and reduce the risk of serious injury from design deficiencies.1.1 These test methods specify procedures and equipment used for testing and evaluating a motorized treadmill for compliance to Specification F 2115. Both design and operational parameters will be evaluated. Where possible and applicable, accepted test methods from other recognized bodies will be used and referenced. In case of a conflict between this document and Specification F 2115, Specification F 2115 takes precedence.1.2 Requirements8212;A motorized treadmill is to be tested for all of the following parameters:1.2.1 Stability,1.2.2 Exterior design,1.2.3 Endurance,1.2.4 Static loading,1.2.5 Overheating,1.2.6 Adjustable incline system function,1.2.7 User interface parameters,1.2.8 Motorized drive system operation,1.2.9 Warning label compliance, and1.2.10 Documentation.

Standard Test Methods for Evaluating Design and Performance Characteristics of Motorized Treadmills

ASTM F2274-03 条件3自行车轮叉标准规范

1.1 This standard establishes testing requirements for qualifying designs using production forks intended for use in Condition 3 per Classification F 2043.1.2 This standard is applicable to suspension and non-suspension bicycle forks for use of a bicycle on rough trails, rough unpaved roads, and rough technical areas and unimproved trails. Contact with irregular terrain and momentary loss of tire contact with the ground may occur during usage. This usage is referred to as Condition 3 per Classification F 2043. Other types of bicycle uses exist and other specification standards will apply for uses other than Condition 3.

Standard Specification for Condition 3 Bicycle Forks

ASTM F2268-03 自行车序列号的标准规范

1.1 This standard specifies the format, content, number of characters and physical requirements for serial numbers to facilitate recall campaigns and identification of stolen property.1.2 This standard is applicable to all bicycles, refer to Classification F 2043 on definition for bicycle.

Standard Specification for Bicycle Serial Numbers

QB 2566-2002 轻型三轮自行车安全通用技术条件

本标准规定了轻型三轮自行车(以下简称“三轮自行车”)的定义、基本参数、要求、试验方法和检验规则。 本标准适用于两轮在后的三轮自行车。

Light tricycle for delivery use----General technical requirements

DIN 49848-3:2002 自行车用白炽灯.第3部分:C、D、E、F和G类

This standard specifies battery-operated bicycle lighting (Categories C, D, E, F and G) with lamp cap PX13,5s according to DIN EN 60061-1, standard sheet 7004-35-2.#,,#

Bicycle incandescent lamps - Part 3: Categories C, D, E, F and G

DIN 49848-5:2002 自行车用白炽灯.第5部分:TF5类

This standard specifies bicycle incandescent lamps category TF5 with lamp cap BX8,4d-12,5 according to DIN EN 60061-1 (standard sheet under consideration).

Bicycle incandescent lamps - Part 5: Category TF5

DIN 49848-4:2002 自行车用白炽灯.第4部分:HS4类

Bicycle incandescent lamps - Part 4: Category HS4

SN/T 1153-2002 进出口自行车轮胎检验规程

Import and export bicycle tire inspection regulations

DIN V 66353:2002 儿童保护用品.带可反向扶手的婴儿车和幼儿推车.要求和试验

This Prestandard specifies requirements and test methods for prams and pushchairs equipped with reversable handles.

Child care articles - Prams and push chairs with reversable handles - Requirements and tests

ISO 8098:2002 自行车.幼童用自行车的安全性要求

This International Standard specifies safety and performance requirements and test methods for the design, assembly and testing of bicycles for young children of from about four to eight years of age, as well as these bicycles' sub-assemblies. It also provides guidelines for instructions on the use and care of the bicycles. This International Standard is applicable to bicycles with a maximum saddle height of more than 435 mm and less than 635 mm, propelled by a transmitted drive to the rear wheel. It is not applicable to special bicycles intended for stunting (e.g. BMX bicycles).

Cycles - Safety requirements for bicycles for young children

ISO 7176-23:2002 轮椅.第23部分:服务员操作阶梯攀登器械的要求和试验方法

This part of ISO 7176 specifies requirements and test methods for electrically propelled stair-climbing devices and stair-climbing wheelchair carriers operated by an attendant. It also includes ergonomic, safety labelling and disclosure requirements. This part of ISO 7176 is applicable to stair-climbing devices for which the attendant walks directly behind the device and where the device is driven backwards when ascending stairs. NOTE This means that when ascending stairs the attendant walks backwards up the stairs, with the occupant facing downstairs. Descending stairs is performed forwards with the occupant facing downstairs.

Wheelchairs - Part 23: Requirements and test methods for attendant-operated stair-climbing devices