Y14 自行车 标准查询与下载

JIS D 9401:2002 自行车车架组件

Frame-assembly for bicycles

BS ISO 7176-6:2002 轮椅.电动轮椅最大速度、加速度及减速度的测定

This part of ISO 7176 specifies test methods for determining the maximum speed, acceleration and deceleration of electrically powered wheelchairs, including scooters, intended to carry one person, with a maximum nominal speed not exceeding 15 km/h (4,167 m/s).

Wheelchairs - Determination of maximum speed, acceleration and deceleration of electric wheelchairs

ASTM F2194-02 小儿睡车和摇篮的用户安全标准规范

1.1 This consumer safety performance specification establishes performance requirements, test methods, and marking requirements to promote safe use of bassinets and cradles.1.2 This consumer safety performance specification is intended to minimize the risks of incidents to an infant resulting from normal use and reasonably foreseeable misuse of a bassinet or cradle.1.3 This specification covers products intended to provide sleeping accommodations (excluding full-size cribs, non-full-size cribs, and bassinets attached to play yards or swings) for an infant up to approximately 5 months in age. Products used in conjunction with a play yard, non-full-size crib, or an infant swing are not covered by this standard.1.4 No bassinet or cradle produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.1.5 This safety performance specification is not intended to address incidents and injuries resulting from alteration or unreasonable abuse or misuse of the product by a child or child care giver.1.6 The following precautionary caveat pertains only to the test method portion Section 7 of this consumer safety specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Consumer Safety Specification for Bassinets and Cradles

ASTM F1975-02 载人用非动力自行车挂斗车标准规范

1.1 This specification covers nonpowered trailers intended to be pulled behind bicycles in order to transport one or two children with accessory loads with a maximum weight of 45.4 kg (100 lb). It includes test methods for confirming that this specification is satisfied. 1.2 The values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only. 1.3 The following caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nonpowered Bicycle Trailers Designed for Human Passengers

JIS D 9431:2001 自行车.鞍座

この規格は，主にJTS D 9111に定める一般用自転車及び幼児用白転車に用いるサドル(以下，サドルという。)について規定する。

Bicycles -- Saddles

JIS D 9418:2001 自行车.飞轮及轮毂齿轮

この規格は，主にJlS D 9111に定める一般用自転車及び幼児用自転車に用いるフリーホイール及び小ギヤについて規定する。

Bicycles -- Free wheels and hub cogs

JIS D 9451:2001 自行车.车铃

Bicycles -- Bells

JIS D 9201:2001 自行车.刹车的试验方法

この規格は，JIS D 9111に規定する一般用自転車の制動試験方法について規定する。

Bicycles -- Method of braking test

JIS D 9415:2001 自行车.链轮和曲柄

この規格は，主にJIS D 9111に定める一般用自転車及び幼児用自転車に用いるギャクランク(以下，ギヤクランクという。)について規定する。

Bicycles -- Chainwheels and cranks

BS ISO 10542-1:2001 残疾人用技术系统和辅助器具.轮椅系留和乘员约束系统..全部系统的要求和试验方法

This part of ISO 10542 specifies test methods and requirements for design and performance, for instructions and warnings to installers and users, and for product marking and labelling for wheelchair tiedown and occupant-restraint systems (WTORS). It applies to all WTORS that use belt-type occupant restraints that are intended for adult-occupied wheelchairs used as forward-facing seats by passengers and drivers of motor vehicles. This part of ISO 10542 applies primarily to complete WTORS, but other parts of ISO 10542 can also be applied to components and subassemblies sold separately and for replacement parts. This part of ISO 10542 applies to WTORS intended for use with all types of manual and powered wheelchairs intended for use by adults, including three- and four-wheeled scooters.

Technical systems and aids for disabled or handicapped persons - Wheelchair tiedown and occupant-restraint systems - Requirements and test methods for all systems

BS ISO 10542-2:2001 残疾人用技术系统和辅助器具.轮椅系留和乘员约束系统.四点带式系留系统

This part of ISO 10542 specifies test methods and requirements for design and performance, for instructions and warnings to installers and users, and for product marking and labelling for wheelchair tiedown and occupant-restraint systems (WTORS). It applies only to WTORS that use belt-type occupant restraints and four-point strap-type wheelchair tiedowns that are intended for adult-occupied wheelchairs used as forward-facing seats by passengers and drivers of motor vehicles. This part of ISO 10542 applies primarily to complete WTORS, but other parts of ISO 10542 can also be applied to components and subassemblies sold separately and as replacement parts. This part of ISO 10542 applies to WTORS intended for use with all types of manual and powered wheelchairs intended for use by adults, including three- and four-wheeled scooters.

Technical systems and aids for disabled or handicapped persons - Wheelchair tiedown and occupant-restraint systems - Four-point strap-type tiedown systems

BS ISO 7176-2:2001 轮椅.电动轮椅动态稳定性的测定

This part of ISO 7176 specifies test methods for determining the dynamic stability of electrically powered wheelchairs. This part of ISO 7176 is applicable to electrically powered wheelchairs including scooters with a maximum nominal speed not exceeding 15 km/h, intended to carry one person.

Wheelchairs - Determination of dynamic stability of electric wheelchairs

ISO 7176-19:2001 轮椅 第19部分：机动车辆用有轮移动设备

This part of ISO 7176 specifies wheelchair design and performance requirements and associated test methods, as well as requirements for wheelchair labelling, presale literature disclosure, user instructions and user warnings. These requirements are applicable to wheelchairs that are designed to be secured by any type of wheelchair tiedown in accordance with ISO 10542-1 and any other applicable parts of the ISO 10542 series. This part of ISO 7176 applies to all manual and powered wheelchairs, including scooters, which, in addition to their intended function as mobility devices, are also intended for use as forward-facing seating by adult occupants of motor vehicles. It also applies to wheelchairs with add-on components designed to meet one or more of the requirements of this part of ISO 7176.

Wheelchairs - Part 19: Wheeled mobility devices for use in motor vehicles

ISO 7176-9:2001 轮椅 第9部分:电动轮椅的耐气候试验

This part of ISO 7176 specifies requirements and test methods to determine the effects of rain and condensation and the effects of changes of temperature on the basic functioning of electrically powered wheelchairs, including scooters, intended to carry one person, with a maximum speed not exceeding 15 km/h. This part of ISO 7176 does not include requirements for resistance to corrosion.

Wheelchairs - Part 9: Climatic tests for electric wheelchairs

ISO 7176-6:2001 轮椅 第6部分:电动轮椅最大速度、加速度及减速的测定

This part of ISO 7176 specifies test methods for determining the maximum speed, acceleration and deceleration of electrically powered wheelchairs, including scooters, intended to carry one person, with a maximum nominal speed not exceeding 15 km/h (4,167 m/s).

Wheelchairs - Part 6: Determination of maximum speed, acceleration and deceleration of electric wheelchairs

JIS T 9240:2001 残疾人输送用升降机的一般要求

この規格は，自力での移動や移乗が困難な人を対象に使用するリフト(以下，リフトという。)の一般的事項について規定する。ただし，異なる階上への移動用機器には適用しない。

General requirements relative to hoists for the transfer of disabled persons

PD ISO/TR 13570:2001 ISO 7176 系列轮椅应用指南

The purpose of this report is to explain how you can use the International Standards on wheelchairs to select your next wheelchair. Is meant to help you understand the purpose for and content of International Standards on wheelchairs.

Guidelines for the application of the ISO 7176 series on wheelchairs

BS ISO 9633:2001 自行车链条.特性和试验方法

This International Standard specifies the dimensions and mechanical properties of cycle chains, as well as test methods for determining these mechanical properties (i.e. twist, lateral deviation, stiff link and side bow). NOTE The dimensions of sprockets for cycle chains are specified in ISO 606.

Cycle chains - Characteristics and test methods

ISO 9633:2001 自行车链条 特性和试验方法

This International Standard specifies the dimensions and mechanical properties of cycle chains, as well as test methods for determining these mechanical properties (i.e. twist, lateral deviation, stiff link and side bow). NOTE The dimensions of sprockets for cycle chains are specified in ISO 606.

Cycle chains - Characteristics and test methods

ISO 7176-2:2001 轮椅 第2部分:电动轮椅动态稳定性的测定

This part of ISO 7176 specifies test methods for determining the dynamic stability of electrically powered wheelchairs. This part of ISO 7176 is applicable to electrically powered wheelchairs including scooters with a maximum nominal speed not exceeding 15 km/h, intended to carry one person.

Wheelchairs - Part 2: Determination of dynamic stability of electric wheelchairs