Y14 自行车 标准查询与下载

JIS T 9206:2001 电动轮椅和机动小型摩托车的电磁兼容性要求和试验方法

この規格は，身体障害者用で，最高時速15km以下の，屋内用及び屋外用電動車いす並びに電動スクータの電磁エミッション及び電磁ィミュニティに関する要件と試験方法について規定する。

Requirements and test methods for electromagnetic compatibility of electrically powered wheelchairs and motorized scooters

ISO/TR 13570:2001 有关轮椅的ISO 7176系列标准的应用指南

Guidelines for the application of the ISO 7176 series on wheelchairs

ASTM F833-01 客车及婴儿四轮车的使用者安全性能标准规范

1.1 This consumer safety specification establishes safety performance requirements, test methods, and requirements for labeling to minimize the hazards to children presented by carriages and strollers as identified in the introduction. 1.2 No carriage or stroller produced after the approval date of this consumer safety performance shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements herein. 1.3 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only. 1.4 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Performance Specification for Carriages and Strollers

ASTM F2115-01 装有发动机的人力蹋车的标准规范

1.1 This specification covers the establishment of parameters for the design and manufacture of motorized treadmills.

Standard Specification for Motorized Treadmills

ISO 7176-22:2000 轮椅 第22部分:安装程序

This part of ISO 7176 specifies a set-up procedure to be used in the preparation of adjustable wheelchairs for testing in accordance with the ISO 7176 series. This procedure gives methods to be used where there are no manufacturers' instructions for setting the wheelchair adjustments. This part of ISO 7176 is applicable to manual wheelchairs and electric wheelchairs (including scooters) intended to provide indoor and/or outdoor mobility. Other parts of ISO 7176 may give specific requirements for the adjustment of the wheelchair. In such cases, that individual part of ISO 7176 takes precedence over this part of ISO 7176.

Wheelchairs - Part 22: Set-up procedures

ISO 7859:2000 轻便摩托车 燃料消耗测量

This International Standard specifies two tests for determining the fuel consumption of mopeds. It is applicable to mopeds as defined in ISO 3833.

Mopeds - Fuel consumption measurements

DIN 79100:2000 自行车.安全要求和试验方法

Bicycles - Safety requirements and test methods

JIS D 9207:2000 电动自行车.每次充足电情况下行使距离的试验方法

この規格は，完全充電したバッテリを搭載した二輪及び三輪の電動アシスト自転車において，そのバッテリによってアシスト機能が持続する距離をシャシダイナモメータ上で測定する方法について規定する。

Electric power assist bicycles -- Test method of travelling distance per full charging

ASTM F1975-00 载人用非动力自行车挂斗车标准规范

1.1 This specification covers nonpowered trailers intended to be pulled behind bicycles in order to transport one or two children with accessory loads with a maximum weight of 45.4 kg (100 lb). It includes test methods for confirming that this specification is satisfied. 1.2 The values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only. 1.3 The following caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nonpowered Bicycle Trailers Designed for Human Passengers

ASTM F1625-00(2008) 后悬挂式自行车儿童座椅的标准规范和试验方法

1.1 This specification covers child carriers that mount to the rear of bicycles in order to transport children or accessory loads with a maximum weight of 18 kg (40 lb). This specification does not apply to child carriers that mount in front of the handlebars, or to the top tube, head tube, or behind the handlebars in front of the rider. Note 18212;In the instructions, the manufacturer must warn the rider that a load added to the bicycle will lessen the stability and alter the riding characteristics of the bicycle. This complication is particularly important when riding with children who are near the high end of the weight range. 1.2 The following safety hazards caveat pertains only to the test method portions, Sections 5, 6, and 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification and Test Method for Rear-Mounted Bicycle Child Carriers

ASTM F2043-00 自行车用法的标准分类

This classification provides a uniform set of usage definitions within the bicycle industry.1.1. This classification covers bicycle usage conditions.

Standard Classification for Bicycle Usage

ANSI/ASTM F1625:2000 后悬挂式自行车儿童座椅的规范和试验方法

Specification and Test Method for Rear-Mounted Bicycle Child Carriers

ASTM F1625-00 安置在自行车的前面和后面的儿童座椅的标准规范和试验方法

1.1 This specification covers child carriers that mount to the rear of bicycles in order to transport children or accessory loads with a maximum weight of 18 kg (40 lb). This specification does not apply to child carriers that mount in front of the handlebars, or to the top tube, head tube, or behind the handlebars in front of the rider.Note 1-- In the instructions, the manufacturer must warn the rider that a load added to the bicycle will lessen the stability and alter the riding characteristics of the bicycle. This complication is particularly important when riding with children who are near the high end of the weight range.1.2 The following safety hazards caveat pertains only to the test method portions, Sections 5 ,6 , and7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification and Test Method for Rear-Mounted Bicycle Child Carriers

BS ISO 7176-1:1999 轮椅.静态稳定性的测定

This part of ISO 7176 specifies the test methods for determining the static tipping stability of wheelchairs, including scooters. This part of ISO 7176 is applicable to wheelchairs and vehicles that are included in the 12.21 series described in ISO 9999 and are intended to provide indoor and outdoor mobility for people with disabilities whose mass does not exceed the maximum mass of the test dummy given in ISO 7176-11.

Wheelchairs - Determination of static stability

ISO 7176-1:1999 轮椅 第1部分:静态稳定性的测定

This part of ISO 7176 specifies the test methods for determining the static tipping stability of wheelchairs, including scooters. This part of ISO 7176 is applicable to wheelchairs and vehicles that are included in the 12.21 series described in ISO 9999 and are intended to provide indoor and outdoor mobility for people with disabilities whose mass does not exceed the maximum mass of the test dummy given in ISO 7176-11.

Wheelchairs - Part 1: Determination of static stability

JIS T 9203:1999 电动轮椅

Electric wheelchairs

BS EN 12184:1999 电动轮椅、小型摩托车及其充电器.要求和试验方法

This European Standard specifies requirements and test methods for electrically powered wheelchairs and scooters with a maximum speed not exceeding 15 km/h intended to carry one person whose mass does not exceed 100 kg, including the following classifications from EN ISO 9999:1998: 12 21 21 Powered attendant-controlled wheelchairs 12 21 24 Electric motor-driven wheelchairs with manual steering 12 21 27 Electric motor-driven wheelchairs with powered steering It also specifies requirements and test methods for manual wheelchairs with add on power kits used for propulsion. It also specifies requirements and test methods for battery chargers for wheelchairs and scooters. This European Standard does not apply in total to: —wheelchairs intended for special purposes, such as sports; —manually propelled wheelchairs with electrically powered ancillary equipment (only electrical features); —custom-made wheelchairs; —wheelchairs specially designed for, or with adaptations for, specific disabled persons; —powered office chairs. NOTE 1 The requirement for manually propelled wheelchairs with electrically powered ancillary equipment is specified in EN 12183:1999. NOTE 2 Appropriate parts of the standard may be applied to the above products and other wheelchairs outside this Scope. NOTE 3 The application of the standard is limited to wheelchairs with a maximum occupant mass of 100 kg because this is the maximum mass of dummy available in ISO 7176-11. Further work is needed to investigate the effects of people with larger body masses.

Electrically powered wheelchairs, scooters and their chargers - Requirements and test methods

ISO 14722:1998 轻便摩托车及其驾驶员运动学 词汇

1 This International Standard defines terms, symbols and conventions related to moped and moped-rider motions and kinematics and to the modelling thereof. 2 It does not deal with methods of measurement, nor with the units used in reporting the results, nor with accuracy. 3 The definitions in this International Standard apply to two-wheeled mopeds as defined in ISO 3833. 4 This International Standard does not cover road mopeds which are controlled by a pedestrian or which are used for the carriage of goods to the exclusion of persons.

Moped and moped-rider kinematics - Vocabulary

QB/T 2416-1998 独轮车

本标准规定了独轮车的产品分类、技术要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于非竞赛用独轮车。

wheelbarrow

JIS C 9502:1998 自行车用动力灯

この規格は，JIS D 9111に規定する自転車に取り付けて使用する発電ランプ(バッテリ式を含む。)の測光,物理要件，試験方法及び表示要件について規定する。ただし，幼児用自転車，特殊自転車の一部のレーサ用，一輪車など一般的に夜間，かつ，公道を走らないものは除く。

Dynamo lamps for bicycles