Y31 纸浆与纸板 标准查询与下载



共找到 637 条与 纸浆与纸板 相关的标准,共 43

이 표준은 수직으로 매달린 시험편을 이용하여 종이의 컬(curl)을 측정하는 방법에 대해

Paper and board-Determination of curl using a single vertically suspended test piece

ICS
85.060
CCS
Y31
发布
2009-11-05
实施
2009-11-05

이 표준은 PFI 밀을 사용한 펄프의 실험실적 고해 방법에 대하여 규정한다. 이 표준은 펄

Pulps-Laboratory beating-Part 2:PFI mill method

ICS
85.04
CCS
Y31
发布
2009-11-05
实施
2009-11-05

이 표준은 일반적인 산업용으로 쓰이는 폴리우레탄 합성물로 성형된 부츠에 대한 요구사항을 규

Moulded plastics footwear-Lined or unlined polyurethane boots for general industrial use-Specification

ICS
13.340.50
CCS
Y31
发布
2009-09-04
实施
2009-09-04

本标准规定了进出口纸浆的检验项目及要求、取样、试验方法及判定规则。 本标准适用于进出口化学木浆、机械木浆和绒毛浆的检验。 本标准不适用于溶解级化学木浆的检验。

Rules for the inspection of pulp for import and export

ICS
CCS
Y31
发布
2009-09-02
实施
2010-03-16

This part of ISO 5263 specifies an apparatus and the procedures for the laboratory wet disintegration of mechanical pulps that exhibit latency. This apparatus and procedure are required for preparation of the test portion in a number of other International Standards dealing with pulps. ISO 5263-3 is applicable to all kind of mechanical pulps (i.e. mechanical, semi-chemical and chemimechanical pulps) exhibiting latency. Mechanical pulps not exhibiting latency shall be disintegrated according to ISO 5263-2. The procedure specified in ISO 5263-2 should be used to disintegrate all mechanical pulps to be measured for brightness. NOTE Brightness is not significantly altered by the presence of latency; however, hot disintegration of mechanical pulps can lead to significant loss of brightness.

Pulps — Laboratory wet disintegration Part 3: Disintegration of mechanical pulps at > 85 °C (ISO 5263-3:2004)

ICS
85.040
CCS
Y31
发布
2009-04-30
实施
2009-04-30

Testing of board - Short span test of solid board

ICS
85.060
CCS
Y31
发布
2009-04
实施

이 표준은 비편광을 이용한 자동 광학분석에 의하여 섬유장을 측정하는 방법에 대하여 규정한다

Pulps-Determination of fiber length by automated optical analysis-Part 2:Unpolarized light method

ICS
85.04
CCS
Y31
发布
2009-01-15
实施
2009-01-15

이 표준은 모든 종류의 펄프에 대한 보수도를 측정하기 위한 방법을 규정한다.

Pulps-Determination of water retention value(WRV)

ICS
85.04
CCS
Y31
发布
2009-01-15
实施
2009-01-15

이 표준은 골판지의 수직 압축강도를 측정하는 방법(가장자리에 왁스를 도포하지 않는 방법)에

Corrugated fiberboard-Determination of edgewise crush resistance(unwaxed edge method)

ICS
85.06
CCS
Y31
发布
2009-01-15
实施
2009-01-15

이 표준은 물리적 면적 범위가 0.02 mm2에서 3.0 mm2 이내인 협잡물 반점의 검정

Pulps-Estimation of dirt and shives-Part 4:Instrumental inspection by reflected light using Equivalent Black Area(EBA) method

ICS
85.040
CCS
Y31
发布
2009-01-15
实施
2009-01-15

이 표준은 반사광을 이용하여 종이에 있는 이물질을 육안으로 평가하는 시험방법에 대하여 규정

Paper and board-Estimation of contraries

ICS
85.040
CCS
Y31
发布
2008-12-29
实施
2008-12-29

이 표준은 시트 형태로 싸이고 단위 베일로 수송하는 펄프 다발의 건조도를 측정하고 거래 중

Pulps-Determination of saleable mass in lots-Part 3:Unitized bales

ICS
85.040
CCS
Y31
发布
2008-12-29
实施
2008-12-29

이 표준은 시트 형태로 싸인 펄프 베일의 건조도를 측정하고 거래 중량을 산출하는 방법을 규

Pulps-Determination of saleable mass in lots-Part 1:Pulps baled in sheet form

ICS
85.040.00
CCS
Y31
发布
2008-12-29
实施
2008-12-29

이 표준은 공차 중량(KS R ISO 1176에 정의)이 3.5 t 이하인 상용차의 내연

Rubber hoses and tubing for cooling systems for internal-combustion engines-Specification

ICS
43.040.01;83.140.40
CCS
Y31
发布
2008-11-26
实施
2008-11-26

Pulps - Preparation of laboratory sheets for physical testing - Conventional and Rapid-Köthen sheet formers using a closed water system

ICS
85.040
CCS
Y31
发布
2008-10-31
实施
2008-10-31

1.1 이 표준은 성형 및 압출 플라스틱의 인장강도를 측정하기 위한 시료의 상태 조절 조건

Plastics-Determination of tensile properties-Part 2:Test conditions for moulding and extrusion plastics

ICS
83.080.00
CCS
Y31
发布
2008-10-28
实施
2008-10-28

이 표준은 표준 시험편 및 규정된 시험편 제조와 시험 조건하에서 시험이 이루어질 때의 경질

Adhesives-Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies

ICS
83.180
CCS
Y31
发布
2008-10-28
实施
2008-10-28

이 표준은 프린트-서프 장치를 이용하여 종이와 판지의 거칠기를 측정하는 방법에 대하여 규정

Paper and board-Determination of roughness/smoothness (air leak methods)-Part 4:Print-surf method

ICS
85.060
CCS
Y31
发布
2008-09-18
实施
2008-09-18

이 표준은 인쇄 공정에서의 거동을 모사하여, 도공지, 미도공지 및 판지의 피킹(pickin

Paper and board-Determination of resistance to picking-Accelerated speed method using the IGT-type tester(electric model)

ICS
85.060
CCS
Y31
发布
2008-09-18
实施
2008-09-18

Testing of board - Creasings - Part 3: Determination of the technical quality

ICS
85.060
CCS
Y31
发布
2008-05
实施



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号