Y43 牙膏、肥皂、洗涤剂 标准查询与下载

QB/T 2115-1995 洗涤剂中碳酸盐含量的测定

本标准规定了测定洗涤剂中碳酸盐含量的方法。 本标准适用于测定粉(粒)状、膏状和液体洗涤剂中的碳酸盐含量。

Determination of carbonate content in detergents

QB/T 2113-1995 低磷无磷洗衣粉

本标准规定了低磷无磷洗衣粉的产品分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于由表面活性剂和助洗剂配方生产的聚磷酸盐含量小于14%的低磷酸盐洗衣粉和无磷酸盐洗衣粉。亦适用于加醉的低碑无碑洗衣粉。

Low Phosphorus Phosphorus Free Laundry Powder

QB/T 2116-1995 洗衣膏

本标准规定了洗衣膏的技术要求、试验方法、检验规则和标志、包装、运输、贮存条件。 本标准适用于由表面活性剂和三聚磷酸钠、4A沸石等助洗剂配制的弱碱性洗衣膏。

Laundry Cream

QB/T 2114-1995 低磷无磷洗涤剂中硅酸盐含量（以SiO2计）的测定 滴定法

本标准规定了测定低磷无磷洗涤剂中硅酸盐含量(以SiO2计)的滴定法。 本标准适用于礴酸盐含量不超过15%的粉(粒)状、*状和液体洗涤剂中硅酸盐含量(以SiO2计)的测定。

Titration method for the determination of silicate content (calculated as SiO2) in low-phosphorus and non-phosphorus detergents

DLA A-A-461 B-1995 洗手液(包装好的预湿纸巾)

The General Services Administration has authorized the use　of this Commercial Item Description, for all federal agencies.

HAND CLEANER (PRE-MOISTENED PAPER TOWELETTE IN PACKET)

NAVY MIL-C-22230 B (2)-1995 燃料水槽及舱底洗涤剂

This amendment forms a part of MIL-C-22230B(SH), dated 19 October 1987, and is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department Defense.

CLEANING COMPOUND, FUEL TANK AND BILGE

BS 4088-3:1995 地板清洗产品.喷雾清洗机用液态配方规范

This Part of BS 4088 specifies requirements for physical, chemical and performance properties of formulations which are used with water in spray extraction machines for cleaning textile floor coverings. Requirements for labelling and instructions for use are also specified. NOTE. Products containing additives with functions other than cleaning may conform with this Part of BS 4088. Typical additives include optical brightening agents, colorants, preservatives, antimicrobial agents, soil-resistant and stain-resistant agents, perfume and odour neutralizing compounds.

Carpet cleaning products - Specification for spray extraction machine formulations used in liquid form

BS 4088-4:1995 地毯清洁制品.第4部分:浸入洗涤粉配方规范

This Part of BS 4088 specifies requirements for the physical, chemical and performance properties of impregnated powder formulations (hereafter generally referred to as 'the product'), used for cleaning textile floor coverings. Requirements for labelling and instructions for use are also specified. NOTE. Impregnated powder formulations are also referred to as 'dry powder cleaners'.

Carpet cleaning products - Specification for impregnated powder formulations

ASTM D5547-95 原子吸收法测定粉未洗涤剂中的粘土和沸石的标准试验方法

1.1 This test method covers atomic absorption tests applicable to powdered laundry detergents containing clay and zeolite. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Clay and Zeolite in Powdered Laundry Detergents by Atomic Absorption

ASTM D1172-95(2007) 肥皂和洗涤剂水溶液pH值的标准测试方法

1.1 This guide covers the preparation of aqueous solutions of soaps and detergents and the determination of their pH.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

Standard Guide for pH of Aqueous Solutions of Soaps and Detergents

ASTM D5547-95(2009) 原子吸收法测定粉未洗涤剂中的粘土和沸石的标准试验方法

1.1 This test method covers atomic absorption tests applicable to powdered laundry detergents containing clay and zeolite. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Clay and Zeolite in Powdered Laundry Detergents by Atomic Absorption

ASTM D4008-95(2009) 测量洗衣用洗涤剂防污物沉积性的标准试验方法(不适于洗涤剂的分级)

The test as now constituted is not suitable for ranking of detergent products, since no basis is available at this time for correlation of the anti-deposition performance of detergents using any particular combination of soils and fabrics with anti-redeposition performance during washing of naturally soiled articles. A suggested procedure for comparing the performance of any two laundry detergents or naturally soiled family items in home laundry equipment, under controlled conditions on a paired comparison basis, is described in Method D2960.1.1 This test method provides guidelines for measuring the ability of detergents to prevent the deposition of soils from detergent solutions onto fabrics. It is intended as a laboratory screening test to aid in the formulation of detergent products, for quality control, and as a basis between the purchaser and seller in standardizing specific products' performance. 1.2 The anti-soil deposition performance of detergent products will vary greatly depending on the type of soils and fabrics used in the test. Therefore, selection of the soils, fabrics, reference detergents, and test conditions shall be made by agreement between the interested parties on the basis of experience. 1.3 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material safety data sheets are available for reagents and materials. Review them for hazards prior to usage.

Standard Test Method for Measuring Anti-Soil Deposition Properties of Laundry Detergents (Not Suitable for Detergent Ranking)

ASTM D4488-95 弹性地板材和可洗墙用的产品清洗特性测试的标准指南

1.1 This guide covers the evaluation of the cleaning per- formance of products intended for use on resilient flooring or washable walls. Such evaluations specifically exclude windows, mirrors, carpets, ceramic tiles, and laminated counter tops. This guide provides techniques for soiling, cleaning, and evaluating performance of detergent systems under con- trolled, but practical, hard-surface cleaning conditions. 1.2 Such systems include any detergent intended for clean- ing hard surfaces such as resilient flooring, washable wall surfaces, and other hard surfaces, but excluding glass, ceramic, or other glossy surfaces. They may consist of solutions of soluble powdered detergent, dilutions of concentrated liq- uid detergent, or products intended to be used full strength, for example, foams, sprays, liquid, or paste. 1.3 There is no universal soil/substrate combination that is representative of the many soil-removal tasks required of this type of cleaner in actual use conditions. Choice of soil/ substrate and cleaning conditions should be by agreement between the testing laboratory and those using the data to evaluate cleaning performance relative to user experience. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents. Review them for hazards prior to usage. Specific precautionary statements are given in Note 2.

Standard Guide for Testing Cleaning Performance of Products Intended for Use on Resilient Flooring and Washable Walls

ASTM D4488-95(2001)e1 弹性地板材和可洗墙用的产品清洗特性测试的标准指南

This guide suggests methodology for cleaning tests. Soil/substrate combinations are generally designed to be analogous to soiled surfaces commonly encountered. This methodology can be used with most soil/substrate combinations. Some example test methods that have worked well in other labs are provided in the annexes. There is no requirement for using the soils listed in the annexes. It is the responsibility of the user to select the appropriate battery of tests for the desired end results. The results of tests based on this guide are regarded as diagnostic screening values useful in formulation studies, quality control, and ingredient raw material qualification. This guide is intended to allow a choice in test conditions and soil/substrate combinations appropriate to the evaluation at hand. For interlaboratory comparisons, exact test conditions must be established before test results are compared. This guide is applicable to testing all types of multipurpose household cleaners, whether the detergent is prepared by dissolving a soluble powder, a dilutable liquid, or is a pre-diluted product. It may also be useful for evaluation of products or conditions normally associated with industrial or institutional cleaners.1.1 This guide covers the evaluation of the cleaning per- formance of products intended for use on resilient flooring or washable walls. Such evaluations specifically exclude windows, mirrors, carpets, ceramic tiles, and laminated counter tops. This guide provides techniques for soiling, cleaning, and evaluating performance of detergent systems under con- trolled, but practical, hard-surface cleaning conditions. 1.2 Such systems include any detergent intended for clean- ing hard surfaces such as resilient flooring, washable wall surfaces, and other hard surfaces, but excluding glass, ceramic, or other glossy surfaces. They may consist of solutions of soluble powdered detergent, dilutions of concentrated liq- uid detergent, or products intended to be used full strength, for example, foams, sprays, liquid, or paste. 1.3 There is no universal soil/substrate combination that is representative of the many soil-removal tasks required of this type of cleaner in actual use conditions. Choice of soil/ substrate and cleaning conditions should be by agreement between the testing laboratory and those using the data to evaluate cleaning performance relative to user experience. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents. Review them for hazards prior to usage. Specific precautionary statements are given in Note 2.

Standard Guide for Testing Cleaning Performance of Products Intended for Use on Resilient Flooring and Washable Walls

ASTM D4008-95 测量洗衣用洗涤剂防污物沉积性的标准试验方法(不适于洗涤剂的分级)

1.1 This test method provides guidelines for measuring the ability of detergents to prevent the deposition of soils from detergent solutions onto fabrics. It is intended as a laboratory screening test to aid in the formulation of detergent products, for quality control, and as a basis between the purchaser and seller in standardizing specific products' performance. 1.2 The anti-soil deposition performance of detergent products will vary greatly depending on the type of soils and fabrics used in the test. Therefore, selection of the soils, fabrics, reference detergents, and test conditions shall be made by agreement between the interested parties on the basis of experience. 1.3 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material safety data sheets are available for reagents and materials. Review them for hazards prior to usage.

Standard Test Method for Measuring Anti-Soil Deposition Properties of Laundry Detergents (Not Suitable for Detergent Ranking)

ASTM D4008-95(2003) 测量洗衣用洗涤剂防污物沉积性的标准试验方法(不适于洗涤剂的分级)

The test as now constituted is not suitable for ranking of detergent products, since no basis is available at this time for correlation of the anti-deposition performance of detergents using any particular combination of soils and fabrics with anti-redeposition performance during washing of naturally soiled articles. A suggested procedure for comparing the performance of any two laundry detergents or naturally soiled family items in home laundry equipment, under controlled conditions on a paired comparison basis, is described in Method D 2960.1.1 This test method provides guidelines for measuring the ability of detergents to prevent the deposition of soils from detergent solutions onto fabrics. It is intended as a laboratory screening test to aid in the formulation of detergent products, for quality control, and as a basis between the purchaser and seller in standardizing specific products' performance.1.2 The anti-soil deposition performance of detergent products will vary greatly depending on the type of soils and fabrics used in the test. Therefore, selection of the soils, fabrics, reference detergents, and test conditions shall be made by agreement between the interested parties on the basis of experience.1.3 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material safety data sheets are available for reagents and materials. Review them for hazards prior to usage.

Standard Test Method for Measuring Anti-Soil Deposition Properties of Laundry Detergents (Not Suitable for Detergent Ranking)

ASTM D5547-95(2003) 原子吸收法测定粉未洗涤剂中的粘土和沸石的标准试验方法

1.1 This test method covers atomic absorption tests applicable to powdered laundry detergents containing clay and zeolite.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Clay and Zeolite in Powdered Laundry Detergents by Atomic Absorption

ASTM D1172-95 肥皂和洗涤剂水溶液pH值的标准测试方法

1.1 This guide covers the preparation of aqueous solutions of soaps and detergents and the determination of their pH.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

Standard Guide for pH of Aqueous Solutions of Soaps and Detergents

ASTM D1172-95(2001) 肥皂和洗涤剂水溶液pH值的标准测试方法

1.1 This guide covers the preparation of aqueous solutions of soaps and detergents and the determination of their pH.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

Standard Guide for pH of Aqueous Solutions of Soaps and Detergents

ASTM D4494-95(2004) 检测干洗级全氯乙烯中残余气味的标准试验方法

Normally clothes cleaned with perchloroethylene will have a clean cloth odor. If a foreign odor is present, it may be objectionable.1.1 This test method covers the detection of a residual odor in drycleaning-grade perchloroethylene.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

Standard Test Method for Detecting Residual Odor of Drycleaning Grade Perchloroethylene