Y44 其他日用化工品 标准查询与下载

ASTM D1793-92(2008) 地板擦亮乳剂水斑的标准试验方法

This test method measures the ability of a floor polish to resist spotting by water. This test method may be used to measure the extent of damage by a large amount of water or in a separate method to measure the amount of damage by a small amount of water that has evaporated to dryness. Reference polishes should be used for comparison. Note 18212;The test method may induce slight whitening, color change, noticeable change in appearance, including removal of the film, which is caused by contact with water.1.1 This test method covers the determination of water spotting resistance of water emulsion floor polishes. The test method approximates the actual conditions of water spotting encountered in service. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Water Spotting of Emulsion Floor Polishes

ASTM E653-91(2009) 气雾及喷雾杀虫剂杀飞行昆虫效力的标准试验方法

This test method provides a satisfactory means of determining the relative efficacy of aerosol and pressurized space spray insecticide formulations against house flies (Musca domestica, L) strains. Test data obtained by this test method may also be adequate to support label claims for the use of the product against mosquitoes, gnats, flying moths, wasps, and certain other small flying insects. This test method is not designed to measure the residual activity. As a biological test, it is subject to the variations that accompany the reaction of living organisms. It should be employed under the supervision of personnel familiar with the biological testing of insecticides.1.1 This test method determines the effectiveness of aerosol and pressurized space-spray insecticides against house flies (Musca domestica L) and, with modifications in dosage, other flying insects. 1.2 The test may be conducted using approximately 100 house flies per test (small group) or 500 flies per test (large group). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Effectiveness of Aerosol and Pressurized Space Spray Insecticides Against Flying Insects

ASTM E652-91(2009) 无残效液体家用飞虫杀虫剂的标准试验方法

This test method provides a satisfactory means of determining the relative efficacy of spray formulations against house flies (Musca domestica, L). Test data obtained by this test method may also be adequate to support label claims for the use of the product against mosquitoes, gnats, flying moths, wasps, and certain other small flying insects. This test method is not designed to measure the residual action of the spray formulation. As a biological test, it is subject to the variations that accompany the reactions of living organisms. It should be employed under the supervision of personnel familiar with the biological testing of insecticides.1.1 This test method covers the determination of the relative efficiency of household and industrial-use, contact insecticides dissolved in base oils. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Nonresidual Liquid Household Insecticides Against Flying Insects

BOCA ARTICLE 32 NFPC-1990 火柴.第8版

The fire prevention code official shall recommend to the chief administrative official of the municipality the location or relocation of new or existing fire hydrants and the placement or replacement of inadequate water mains located upon public prope

Matches Eighth Edition

BOCA ARTICLE 27 NFPC-1990 烟花.第8版

The following is a listing of the standards referenced in this code, the effective date of the standard, the promulgating agency of the standard and the section(s) of this code that refer to the standard.

Fireworks Eighth Edition

BOCA ARTICLE 27 NFPC COMM-1990 烟花爆竹

The format and provisions of The BOCA National Propero Maintenance Code are designed to provide units of government with an effective regulatory means of providing minimum health and safety requirements for existing buildings and structures.

Fireworks

BOCA ARTICLE 32 NFPC COMM-1990 火柴

A person shall not willfully fail or refuse to comply with any lawful order or direction of the fire prevention code officiai or to interfere with the compliance attempts of another individual.

Matches

ASTM D4955-89(2008) 汽车抛光剂现场评定的标准实施规程

This practice is intended to define the range of properties to be tested, the apparatus to be used, and the comparisons of automotive polish performance to be made. Since conditions, products, and apparatus vary, considerable discretion must exist among formulators and marketers in these areas and on what properties or performance characteristics are most significant for their products. This practice is intended to be flexible enough to honor this fact within the description of automotive polish in Section 2. The test methods are subjective and empirical in order to conform to the basic characteristics of the class of products and to allow flexibility in testing. This also conforms to typical consumer experience. The practice also allows for flexibility in choice of environmental characteristics under which the durability testing is done. This allows discretion to be exercised by those testing the products in order to provide greatest significance for the products being tested as they are intended for various marketplace needs. 1.1 This practice covers the evaluation of the performance properties of automotive polishes. This practice is applicable to products that are commonly referred to as car/auto wax, cleaner wax, polish, and the like. This practice is limited to a comparison among test polishes, with a standard polish, or both, under the conditions of the individual test. The comparative results are indicative of absolute performance only insofar as the test conditions are representative of all normal application and use conditions. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Field Evaluation of Automotive Polish

ASTM D3757-89(2010) 溶剂型地板抛光剂的制备规格的标准指南

This guide may be the basis for either the buying authority or the consumer to prepare a specification for solvent-based floor polishes (liquid or paste). Specifications prepared under this guide are for products intended for use on all wood and solvent resistant floors. Any reference material utilized and limits set are to be agreed upon by the seller, purchaser, or user.1.1 This is a guide for preparing specifications for solvent-based floor polishes (liquid or paste) that are intended for use on all wood and solvent-resistant floors. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Preparing Specifications for Solvent-based Floor Polishes

ASTM D3052-87(2010) 水乳化地板擦亮剂的标准实施规程

When comparing different floor polishes for an actual field performance, it is important that all surfaces used be prepared in the same way. When this procedure is followed, variations in the test surfaces are minimized.1.1 This practice covers the comparison of the performance of water-emulsion floor polishes on test floors against a reference material. It is applicable to the following types of polishes: 1.1.1 Wax emulsion polishes, 1.1.2 Nonbuffable emulsion polishes, 1.1.3 Detergent-resistant emulsion polishes, household type, and 1.1.4 Detergent-resistant emulsion polishes, industrial type. 1.2 Gloss, leveling, discoloration, traffic marking, slip resistance, and removal ease of these types of floor polishes is rated in comparison to a reference material. Where applicable, detergent resistance is also evaluated. This method is not to be considered as a recommended maintenance procedure. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Rating Water-Emulsion Floor Polishes

ASTM D1455-87(2008) 乳化地板抛光剂60度镜面光泽度的标准试验方法

This test method may be used to evaluate the difference in gloss of dried films of emulsion floor polishes when the light reflected at a 60° angle is measured. Extremely high- or low-gloss polishes may not be differentiated at a 60° angle. A 20° angle measured in accordance with Test Method D 523 may give better definition of gloss.1.1 This test method covers the determination of the 60° specular gloss of films of emulsion floor polish after application to a substrate. Note 18212;Specular gloss is one of several related appearance attributes that produce the sensation of glossiness. For this reason, specular gloss measurements may not always correlate well with visual rankings of glossiness. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for 60x00B0; Specular Gloss of Emulsion Floor Polish

ASTM D3052-87(2003) 额定水乳化地板抛光剂

When comparing different floor polishes for an actual field performance, it is important that all surfaces used be prepared in the same way. When this procedure is followed, variations in the test surfaces are minimized.1.1 This practice covers the comparison of the performance of water-emulsion floor polishes on test floors against a reference material. It is applicable to the following types of polishes:1.1.1 Wax emulsion polishes,1.1.2 Nonbuffable emulsion polishes,1.1.3 Detergent-resistant emulsion polishes, household type, and1.1.4 Detergent-resistant emulsion polishes, industrial type.1.2 Gloss, leveling, discoloration, traffic marking, slip resistance, and removal ease of these types of floor polishes is rated in comparison to a reference material. Where applicable, detergent resistance is also evaluated. This method is not to be considered as a recommended maintenance procedure.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Rating Water-Emulsion Floor Polishes

ASTM D1455-87(2002) 乳化地板抛光剂60度镜面光泽度的试验方法

This test method may be used to evaluate the difference in gloss of dried films of emulsion floor polishes when the light reflected at a 60° angle is measured. Extremely high- or low-gloss polishes may not be differentiated at a 60° angle. A 20° angle measured in accordance with Test Method D 523 may give better definition of gloss.1.1 This test method covers the determination of the 60 specular gloss of films of emulsion floor polish after application to a substrate. Note 18212;Specular gloss is one of several related appearance attributes that produce the sensation of glossiness. For this reason, specular gloss measurements may not always correlate well with visual rankings of glossiness.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for 60176 Specular Gloss of Emulsion Floor Polish

ASTM D3153-87(2002) 水乳化地板抛光剂可再涂覆性的试验方法

The essential practical usage of water-emulsion floor polishes as renewable coatings to protect and beautify floors, depends upon satisfactory recoatability. This test method is useful both in product development and final product testing, as a means of evaluating recoatability.1.1 This test method covers the determination of the effects of the application of a water-emulsion floor polish over a dried coating of the same polish. The method is designed for laboratory bench panel testing. A method is also provided for large area testing. A rating system is provided to indicate the acceptability of the polish based on recoatability performance. Note 18212;Recoatability of a water-emulsion floor polish is a general-performance property, and the determination of it is dependent upon the observation of several other properties of the polish under the specific conditions expressed in this test method. This test method for recoatability is not designed for the evaluation of other properties, except as these properties relate to the recoatability of the specific polish being evaluated under the conditions of this test. 1.2 Gloss as observed herein extends only to freedom from loss of apparent visual gloss upon recoating, in the execution of this test method, and should this loss occur, it indicates a distortion of the property of gloss, by recoating.1.3 A degree of recoatability failure may be reflected from a degree of leveling failure. The failure to level should be observed only if it is to be a part of the observation of recoatability.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Recoatability of Water-Emulsion Floor Polishes

ASTM D3153-87(2008) 水乳化地板抛光剂可再涂覆性的标准试验方法

The essential practical usage of water-emulsion floor polishes as renewable coatings to protect and beautify floors, depends upon satisfactory recoatability. This test method is useful both in product development and final product testing, as a means of evaluating recoatability.1.1 This test method covers the determination of the effects of the application of a water-emulsion floor polish over a dried coating of the same polish. The method is designed for laboratory bench panel testing. A method is also provided for large area testing. A rating system is provided to indicate the acceptability of the polish based on recoatability performance. Note 18212;Recoatability of a water-emulsion floor polish is a general-performance property, and the determination of it is dependent upon the observation of several other properties of the polish under the specific conditions expressed in this test method. This test method for recoatability is not designed for the evaluation of other properties, except as these properties relate to the recoatability of the specific polish being evaluated under the conditions of this test. 1.2 Gloss as observed herein extends only to freedom from loss of apparent visual gloss upon recoating, in the execution of this test method, and should this loss occur, it indicates a distortion of the property of gloss, by recoating. 1.3 A degree of recoatability failure may be reflected from a degree of leveling failure. The failure to level should be observed only if it is to be a part of the observation of recoatability. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Recoatability of Water-Emulsion Floor Polishes

ISO 5565:1982 香草(fragrans Salis-bury Ames)规范

Vanilla (Vanilla fragrans (Salisbury) Ames); Specification

ASTM F766/F766M-82(2010)e1 蜡的熔点标准试验方法

This test method determines the initial melting point and melting range of waxes. The data obtained are important in the application of waxes in one-time carbon inks.1.1 This test method covers the determination of the initial and final melting points and recovery point of waxes using a hot stage and microscope. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 8 for a specific precautionary statement.

Standard Test Method for Melting Point of Waxes

WJ 629-1982 合成樟脑

synthetic camphor

ASTM D3440-82(1995) 水乳化地板擦亮剂制备规格

1.1 This guide covers preparing specifications for water-emulsion floor polishes on all nonwood floors and for sealed wood floors.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Preparing Specifications for Water-Emulsion Floor Polishes

ASTM D4002-81(2002) 使皮面柔软鞋油的评定

This practice is intended to define the properties to be tested, the apparatus to use, and the comparisons of product performance. It is recognized that considerable discretion exists among formulators and marketers of shoe polish on what properties or performance characteristics are best for their products. This practice will be flexible to honor this fact within the confines of the shoe polish definition in 2.1.1.1 This practice covers the definition of properties to test and the apparatus to use, in evaluating the performance of buffable shoe polishes.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Evaluation of Buffable Shoe Polish