Y45 皮革加工与制品综合 标准查询与下载

KS M ISO 5404:2004 皮革.物理和机械试验.厚革的耐水性测定

이 규격은 중가죽(heavy leathers)의 내수성을 측정하기 위한 방법을 설명한다

Leather-Physical and mechanical tests-Determination of the water resistance of heavy leathers

ASTM D2098-04(2012) 道康宁(Dow Corning)皮革试验器测定鞋面革抗流水性的标准试验方法

1.1 This test method covers the determination of the dynamic water resistance of shoe upper leather by means of the Dow Corning Tester. It has been revised to show the state of the art in the equipment used in testing. It is applicable to all types of shoe upper leather. This test method does not apply to wet blue. 1.2 Initial water penetration and water absorption can be measured. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Dynamic Water Resistance of Shoe Upper Leather by the Dow Corning Leather Tester

ASTM D1517-04e1 皮革的相关标准术语

Standard Terminology Relating to Leather

ASTM D1517-04 皮革的相关标准术语

Standard Terminology Relating to Leather

NF G52-036:2003 皮革.物理和机械试验.水蒸气吸收率的测定

Leather - Physical and mechanical tests - Determination of water vapour absorption.

NF G52-010:2003 皮革.物理和机械试验.厚度的测定

Leather - Physical and mechanical tests - Determination of thickness.

NF G52-014:2003 皮革.物理和机械试验.撕裂力的测定.第2部分:双边撕裂

Leather - Physical and mechanical tests - Determination of tear load - Part 2 : double edge tear.

NF G52-011:2003 皮革.物理和机械试验.表观密度的测定

Leather - Physical and mechanical tests - Determination of apparent density.

BS EN ISO 11644:2003 皮革.涂层粘着牢度测定方法

The principle of the method specified is bonding the finished side of part of a strip of leather to an adherend-plate by means of heat-reactivated adhesive film, applying force to the free end of the strip to peel the leather from the finish over a given distance, the finish layer remaining on the adherend-plate together with the film of adhesive. The force required is measured and reported as the adhesion of the finish to the leather. The method is valid for all finished leathers with a smooth surface which can be bonded to an adherend-plate without the adhesive penetrating into the finish.

Leather - Test for adhesion of finish

DIN EN ISO 3378:2003 皮革.物理和机械试验.粒面抗裂强度和折裂指数的测定

This European Standard specifies a method for determining the resistance of leather to grain cracking and for determining the grain crack index. It is applicable to all heavy leathers.

Leather - Physical and mechanical tests; Determination of resistance to grain cracking and grain crack index (ISO 3378:2002); German version EN ISO 3378:2002

DIN EN ISO 2420:2003 皮革.物理和机械试验.表观密度的测定

This European Standard specifies a method for determining the apparent density of leather. It is applicable to all heavy leather.

Leather - Physical and mechanical tests - Determination of apparent density (ISO 2420:2002); German version EN ISO 2420:2002

DIN EN ISO 2589:2003 皮革.物理和机械试验.厚度的测定

This European Standard specifies a method for determining the thickness of leather. The method is applicable to all types of leather of any tannage. The measurement is valid for both the whole leather and a test sample.

Leather - Physical and mechanical tests - Determination of thickness (ISO 2589:2002); German version EN ISO 2589:2002

DIN EN ISO 3380:2003 皮革.物理和机械试验.温度最高达100℃时收缩率的测定

This European Standard describes a method for determination of the shrinkage temperature of leather. It is applicable to all leathers.

Leather - Physical and mechanical tests - Determination of shrinkage temperature up to 100 °C (ISO 3380:2002); German version EN ISO 3380:2002

DIN EN ISO 3376:2003 皮革.物理和机械试验.抗拉强度和伸长率的测定

Leather - Physical and mechanical tests - Determination of tensile strength and percentage extension (ISO 3376:2002); German version EN ISO 3376:2002

DIN EN ISO 17233:2003 皮革.物理和机械试验.表面涂层冷裂温度的测定

This European Standard specifies a method for determining the cold crack temperature of surface coatings applied to leather. It is applicable to all leathers which have a surface coating and which can be easily flexed.

Leather - Physical and mechanical tests - Determination of cold crack temperature of surface coatings (ISO 17233:2002); German version EN ISO 17233:2002

DIN EN ISO 5402:2003 皮革.物理和机械试验.用挠曲计测定耐曲挠性

This European Standard specifies a method for determining the wet or dry flex resistance of leather and finishes applied to leather. It is applicable to all types of leather below 3,0 mm in thickness.#,,#

Leather - Physical and mechanical tests - Determination of flex resistance by flexometer method (ISO 5402:2002); German version EN ISO 5402:2002

DIN EN ISO 17227:2003 皮革.物理和机械试验.皮革耐干热性的测定

This European Standard describes a method of determining the heat resistance of conditionned leathers. It is applicable to all leathers.

Leather - Physical and mechanical tests - Determination of dry heat resistance of leather (ISO 17227:2002); German version EN ISO 17227:2002

DIN EN ISO 17229:2003 皮革.物理和机械试验.水蒸气吸收率的测定

This European Standard describes a method for determining the water vapour absorption of leather. The method can be used for all leathers but is of specific interest for leathers intended for footwear uppers and linings.

Leather - Physical and mechanical tests - Determination of water vapour absorption (ISO 17229:2002); German version EN 17229:2002

DIN EN ISO 3377-2:2003 皮革.物理和机械试验.撕破力的测定.第2部分:双边撕裂

This European Standard describes a method for determining the tear strength of leather using a double edged tear. The method is sometimes described as the Baumann tear. It is applicable to all types of leather.

Leather - Physical and mechanical tests; Determination of tear load - Part 2: Double edge tear (ISO 3377-2:2002); German version EN ISO 3377-2:2002

DIN EN ISO 3377-1:2003 皮革.物理和机械试验.撕破力的测定.第1部分:单边撕裂

This European Standard describes a method for determining the tear strength of leather using a single edged tear. The method is sometimes described as a trouser tear. It is applicable to all types of leather.

Leather - Physical and mechanical tests; Determination of tear load - Part 1: Single edge tear (ISO 3377-1:2002); German version EN ISO 3377-1:2002