Y56 体育用品 标准查询与下载

NF S52-714:2006 高山雪橇装配.安全要求和试验方法

Alpine ski-bindings - Requirements and test methods.

DIN 32926:2006 冰鞋.安全要求和试验方法

This standard is applicable to ice skates used by a person with a body weight up to 100 kg for skating with the exception of competition. It specifies minimum safety requirements for ice skates and requirements for test methods, marking and the information supplied by the manufacturer to reduce the risk of injury for users and third parties in normal use.#,,#

Ice skates - Safety requirements and test methods

DIN EN 13782:2006 临时结构.帐篷.安全性

This European Standard specifies safety requirements which need to be observed at design, calculation, manufacture, installation, maintenance, operation, examination and testing of mobile, temporary installed tents more than 50 m2 ground area. For tents less than 50 m2 ground area, it is not necessary to produce the tent book (see Clause 14) and the producer will provide a documentation concerning the burning behaviour of the fabrics and the stability of the structure. Two tents can be considered as two tents if the distance between them is more than 5 m except otherwise agreed. These tents are intended to be installed and dismounted repeatedly without loss of substance, temporarily as well as on short term or long-term basis at any places, and multiple purposes. A simplified calculation for tents with a maximum space of 12 m and a maximum capacity of 300 people is allowed for traditional pole and rope tents. The field of application of this European Standard covers all kind of temporary covered structures. So the tents erected for a temporary period and dismantled for use elsewhere in fairgrounds and amusement parks are covered by this European Standard. The content of this European Standard collects the different existing national regulations and guidelines as far as possible.

Temporary structures - Tents - Safety English version of DIN EN 13782:2006-05

ISO 7152:1997/Amd 1:2006 野营帐蓬和大蓬车蓬布.术语和等效术语表.修改件1

This is Amendment 1 to ISO 7152-1997 (Camping tents and caravan awnings —Vocabulary and list of equivalent terms )

Camping tents and caravan awnings - Vocabulary and list of equivalent terms; Amendmen 1

KS G 5750-2006 小口径枪的枪口及弹膛尺寸

이 규격은 전술용을 제외한 소구경 총의 총구 및 약실(이하 총구 및 약실이라 한다.)의 치

Dimensions of bore and chamber for small bore rifles and air guns

KS G 5737-2006 起跑架

이 규격은 400 m 이하(4 m×200 m 및 4 m×400 m 계주 경기의 제1주자 포

Starting block

KS G 5738-2006 接力棒

이 규격은 육상 경기의 계주 및 선수 훈련에 사용하는 배턴에 대하여 규정한다.

Baton

DIN ISO 11087:2006 高山雪撬紧固.紧固装置.要求和试验方法 (ISO 11087-2004)

This International Standard specifies the requirements for ski brakes and binding straps. It applies to alpine retention devices which are used to reduce the risk of injury, caused by the ski after the ski's release.

Alpine ski-bindings - Retention devices - Requirements and test methods (ISO 11087:2004);English version of DIN ISO 11087:2006-02

ISO 9462:2006 高山雪橇固定装置.要求和试验方法

This International Standard specifies the main characteristics of ski-bindings and describes, as an example, the test methods A and B. This International Standard applies to ski-bindings for alpine skiing for children, juniors and adults.

Alpine ski-bindings - Requirements and test methods

ISO 13992:2006 高山滑雪板装配.要求和试验方法

This International Standard specifies the main characteristics of touring ski-bindings and describes, as an example, the test methods A and B. This International Standard applies, in principle, to touring ski-bindings for alpine skiing for children, juniors and adults. NOTE As specific touring boots and bindings for children do not exist on the market at present, the scope of this International Standard is limited to bindings for juniors and adults.

Alpine touring ski-bindings - Requirements and test methods

ASTM F2439-06(2011) 英式足球用头部防护帽的标准规格

1.1 This specification defines performance requirements for headgear used for participation in the sport of soccer. The technical requirements in this specification do not address the administrative requirements of soccer governing bodies, so it should not be assumed that any headgear satisfying this specification will be acceptable for use in sanctioned soccer events. 1.2 This specification is intended to reduce the forces from external physical sources reaching the defined impact area of the head in impacts that may occur in the sport of soccer. No headgear can provide protection against all impacts, foreseeable or not. This specification does not address the potential for injury from any type of impact. The tests specified in this specification are laboratory simulation tests only, and do not purport to create situations identical to the impacts that may occur during the playing of soccer. 1.3 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. In the event of a discrepancy between the requirements of this specification and those of Test Methods F1446, this specification shall prevail. 1.4 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear meets all of the requirements of this specification in its entirety. Headgear that fails to meet any one of the requirements of this specification is considered to have failed the specification and should not be sold with any indication that it meets parts of the specification. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Headgear Used in Soccer

DIN ISO 7331:2006 高山滑雪杆.要求和试验方法

This International Standard specifies the minimum requirements for safety in ski-poles for alpine skiing and gives test methods to check conformity with these requirements. It applies to ski-poles for alpine skiing in the following ranges of total length, /T (,see Clause 3): group A. l 1 050 mm (adults' poles); group B, 1 050 mm ＞l ≥ 700 mm (junior poles); group C, l ≤700 mm (children's toy-poles). Special designs may deviate from this International Standard, but are required to be marked durably as special designs (see 8.2).

Ski-poles for alpine skiing - Requirements and test methods (ISO 7331:2005);English version of DIN ISO 7331:2006

ASTM F770-06 娱乐骑乘设施和装置操作方法的标准规范

1.1 This practice establishes information for operating procedures of amusement rides and devices.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Ownership and Operation of Amusement Rides and Devices

ASTM F1064-06 租用的整套和非整套高山滑雪板/绑带/靴系统的抽样和检验的标准实施规程

1.1 This practice establishes a uniform method for the sampling and inspection of complete and incomplete Alpine ski/binding/boot systems used in rental operations. This practice is appropriate for use in rental applications in which all or part of the functional components of the system are supplied by the rental facility.1.2 This practice should be followed by any facility that rents complete or incomplete Alpine ski/binding/boot systems to an end user. Note 1Refer to Practice F 1063 for equivalent procedures and tolerances for retail systems.

Standard Practice for Sampling and Inspection of Complete and Incomplete Alpine Ski/Binding/Boot Systems in Rental Applications

ASTM F939-06 高山滑雪装配的松开扭矩值选择的标准规程

1.1 This practice provides procedures for the selection of release torque values for Alpine ski/boot/bindings systems. These procedures may be used by ski binding manufacturers in their instructions for installation and use and by ski shops for the adjustment of already mounted ski bindings.1.2 This practice is applicable to releasable Alpine ski/boot/binding systems.1.3 Release torque values selected using this practice may not be appropriate for circumstances in which:1.3.1 The skier carries an object that significantly increases the skier's effective body weight,1.3.2 The skier grasps or in some manner controls an object such as a sled, or1.3.3 The skier encounters exceptional snow or terrain conditions not commonly found on developed ski slopes.1.4 This practice may be inappropriate for nonmechanical bindings or bindings used with boots that reach more than half way up the lower leg.1.5 Release torque values outside the recommendations of this practice may increase the risk of injury to the skier. However, skiers who are informed of this potential risk may request such settings and have them provided, subject to any guidelines and limitations specified by the binding manufacturer.1.6 These values refer to recommended release torque for initial adjustment of a ski binding and subsequent readjustment of the binding during routine maintenance or following a suspected malfunction. However, these values are not intended to apply to the condition of the equipment at any time after it is put into use.1.6.1 For information concerning applicable tolerances to be used for the adjustment and inspection of releasable Alpine ski bindings in retail operations consult Practice F 1063; for rental applications consult Practice F 1064 .1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Selection of Release Torque Values for Alpine Ski Bindings

ASTM F2400-06(2011) 用于撑杆跳高的头盔的标准规格

1.1 This specification covers performance requirements for helmets to be used in the activity of pole vaulting. 1.2 All testing and requirements of this specification are to be carried out in accordance with Test Methods F1446 except where noted in this specification. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in their entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the specification and shall not be sold with any indication that it meets parts of the specification. 1.4 Helmets designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Helmets Used in Pole Vaulting

ASTM F2032-06(2011) BMX骑车用头盔的标准规格

1.1 This specification covers performance requirements for helmets used in BMX cycling. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; therefore, this specification requires impact protection over a larger area of the head than Specification F1447 and the CPSC standard. This specification also provides performance criteria for helmets equipped with chin bars. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446 except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear with faceguard meets all of the requirements of the specification in their entirety. A headgear with faceguard that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification. 1.4 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Helmets Used for BMX Cycling

ASTM F2568-06 睡袋测量标准试验方法

In this context, this test can be used for specifications, design, and quality control. Girth in and of itself is not to be used to predict the thermal properties of a sleeping bag.1.1 This test method determines the internal girth, the internal length and width, and the external length and width of a sleeping bag under a standardized measurement method.1.2 The measurement uses a physical measurement method applicable to any location where a flat level surface is provided.1.3 The values stated in inch-pound units are to be regarded as standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Sleeping Bags

ASTM F770-06a 娱乐骑乘设施和装置操作方法的标准规范

The purpose of this practice is to delineate information and to establish procedures for the operation of amusement rides and devices.1.1 This practice covers and establishes information for operating procedures of amusement rides and devices.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Ownership and Operation of Amusement Rides and Devices

ASTM F1976-06 用冲击试验测试运动鞋冲击衰减性能的标准试验方法

This test method is used by athletic footwear manufacturers and others, both as a tool for development of athletic shoe cushioning systems and as a test of the general cushioning characteristics of athletic footwear products. Adherence to the requirements and recommendations of this test method will provide results that can be compared between different laboratories. Data obtained by these procedures are indicative of the shock-attenuating properties of athletic shoe cushioning systems under the specific conditions selected. This test method is designed to provide data on the force versus displacement response of athletic footwear cushioning systems under essentially uniaxial compression conditions at load rates that are similar to those of heel and forefoot impacts during different athletic activities. The peak or maximum values of force, pressure, displacement, and strain are dependent on the maximum energy applied to the specimen. These values are normalized to provide comparative results for a reference maximum energy applied to the specimen of 5 J (44.2 in.-lbf) or 7 J (61.9 in.-lbf). Shock-attenuating characteristics are strongly dependent on specimen size and prior history of force application. Therefore, results should be compared only for specimens of the same nominal shoe size and prior impact conditioning. There are no currently acceptable techniques for normalizing results for specimen thickness variations. Note 28212;Impact-attenuating scores determined by this test method, for athletic shoes, may not correlate with the forces experienced by individual users of the shoes. Note 38212;There is no research showing a correlation between scores on this test method and the probability of injury among users of a particular athletic footwear product.1.1 This test method covers procedures for the measurement of the impact response properties of athletic shoes using Procedure A of Test Method F 1614.1.2 This test method is limited to tests using a falling weight impact machine, as defined by Procedure A of Test Method F 1614.1.3 This test method is intended for use on the heel and or forefoot regions of whole, intact athletic shoe cushioning systems. An athletic shoe cushioning system is defined as all of the layers of material between the wearer''s foot and the ground surface that are normally considered a part of the shoe. This may include any of the following components: outsole or other abrasion resistant layer, a midsole or other compliant cushioning layer, an insole, insole board, or other material layer overlying the midsole, parts of the upper and heel counter reinforcement which extend beneath the foot, and an insock or other cushioning layer inside the shoe.1.4 This test method is not intended for use as a test of shoes classified by the manufacturer as children''s shoes.1.5 The type, size or dimensions and thickness of the specimen, and the reference maximum energy applied shall qualify test results obtained by this test method.1.5.1 Nominal specimen thickness values for this test method are in the range from 10 to 60 mm (0.4 to 2.4 in.). The area of the shoe to be tested must present an approximately circular, flat surface of at least 65 mm (2.6 in.) in diameter for impacting.1.5.2 The standard value for the reference maximum energy applied by this test method is 5 J (44.2 in.-lbf) for shoes which are subject to moderate impacts during normal use and 7.0 J (61.9 in.-lbf) for shoes which are subject to high impacts during normal use. Other values may be used, if they are stated in the report.1.6 This test method is not appropriate for measuring the impact response of shoes that are not subjected to moderate impact or high impact in normal use.1.7 ......

Standard Test Method for Impact Attenuation Properties of Athletic Shoes Using an Impact Test