Y62 家用清洁、整容器具 标准查询与下载

NF C73-808/A1:2006 家用和类似用途电器.安全.第2-8部分:电动剃须刀、电推子和类似电器的特殊要求

Household and similar electrical appliances - Safety - Part 2-8 : particular requirements for shavers, hair clippers and similar appliances.

NF C73-867:2006 家用和类似电气设备.安全性.第2-67部分:工业和商业用地板处理和地板清洁机的特殊要求

Household and similar electrical appliances - Safety - Part 2-67 : particular requirements for floor treatment and floor cleaning machines, for industrial and commercial use.

DIN EN 60704-2-3:2006 家用和类似用途电器.测定空中传播的噪声的试验规程.第2-3部分:洗碗机的特殊要求

These particular requirements apply to single-unit electric dishwashers for household and similar use, with or without automatic programme control, for cold and/or hot water supply, for detachable or permanent connection to water supply or sewage systems, intended for placing on the floor against a wall, for building-in or placing under a counter, a kitchen worktop or under a sink, for wall-mounting or on a counter.#,,#

Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-3: Particular requirements for dishwashers (IEC 60704-2-3:2001 + A1:2005); German version EN 60704-2-3:2002 + A1:2005

UL 921-2006 商用洗碗机

This Standard covers commercial, freestanding, under-counter, and counter-insert dishwashers, utensil-washers, and glass washers using water as the principal cleaning medium, hereafter referred to as dishwashers. These dishwashers utilize steam, gas, or electric heaters for heating the water. Heated water is provided to a dishwasher by means of steam, gas, or electric heating systems integral to the appliance, or by means not integral to the dishwasher that is provided at the installation site. This Standard covers: a) electric dishwashers rated 600 V or less, installed in accordance with the Canadian Electrical Code (CEC), Part 1 CSA C22.1, and the National Electrical Code (NEC) NFPA 70; and b) the gas-handling, gas-burning, and gas-control features of gas-fired dishwashers having inputs of 400,000 Btu (420 MJ) per hour or less, limited to 0.5 psig (3.45 kPa) inlet pressure, installed in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CAN/CSA B149.1 for use with: 1) natural gas, 2) manufactured gas, 3) mixed gas, 4) propane gas, 5) liquefied petroleum gases, or 6) LP gas-air mixtures. These requirements cover dishwashers intended for use in commercial establishments, such as kitchens of restaurants and hospitals, where they are not intended to be accessible to the public.

Commercial dishwashers

ANSI/AHAM AC-2-2006 便携式家用房间电动空气清新器噪声的试验方法

Establishes a method to determine the sound rating of portable household electric room air cleaners. The sound rating is comprised of a set of sound levels that includes: (1) A-weighted sound power level and (2) loundness.

Method for Sound Testing of Portable Household Electric Room Air Cleaners

ASHRAE QC-06-038-2006 全面的,管内气体的空气净化器的实验室测试

Laboratory Testing of Full-Scale In-Duct Gas Air Cleaners

Laboratory Testing of Full-Scale In-Duct Gas Air Cleaners

ASTM F2607-06 测量家用/商用真空吸尘器的硬表面地板清洁能力的标准试验方法

1.1 This test method provides only a laboratory test for determining the relative hard surface floor-cleaning ability of household/commercial vacuum cleaners when tested under specified test conditions.1.2 This test method is applicable to household/commercial types of upright, canister, combination, and stick vacuum cleaners that use a dry primary dirt receptacle and are intended for cleaning hard surface floors as a primary or secondary function.1.3 This test method applies only to the removal of dry debris from hard surface floors, not the removal of embedded dirt from carpet.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring the Hard Surface Floor-Cleaning Ability of Household/Commercial Vacuum Cleaners

ASTM F558-06 测定真空吸尘器的空气性能特征的标准测试方法

The test results allow the comparison of the maximum potential air power available for cleaning tasks when tested under the conditions of this test method. The test results do not indicate the actual air power present during the cleaning process due to the effects of the various tools in use and surfaces being cleaned. During the nozzle on plenum chamber air performance testing, the brushroll is unloaded and this condition is not representative of the brushroll being in contact with carpet or other surfaces being cleaned. FIG. 1 Schematic Diagram of Meter Connections1.1 This test method covers procedures for determining air performance characteristics of commercial and household upright, canister, stick, hand-held, utility, and combination-type vacuum cleaners having provisions for attaching a hose and incorporating a series universal motor. This test method can be applied to the carpet cleaning mode of operation.1.2 These tests and calculations include determination of suction, airflow, air power, maximum air power, and input power under standard operating conditions (see Note 0). The nozzle mounted on plenum testing is an ideal air performance measurement and is not intended to represent the actual air performance during carpet or floor cleaning.Note 0For more information on air performance characteristics, see Refs ().1.3 The foot-pound-inch system of units is used in this standard. The values in parentheses are given for information only.This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in Note 0.

Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaners

ASTM F655-06 真空吸尘器检验用试验地毯和衬垫的标准规范

1.1 This specification provides construction details and a replacement procedure for the standard carpet and pad to be used when testing vacuum cleaners.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing

ASTM F2607-06e1 测量家用/商用真空吸尘器的硬表面地板清洁能力的标准试验方法

This test method will provide an indication of the ability of the vacuum cleaner in removing dry debris from hard surface floors. The cleaning ability in the laboratory test will not be the same as in home cleaning; however, in most cases, a vacuum cleaner that performs well in the laboratory will clean well in a home. To provide a uniform basis for measuring the performance described in 1.1, standardized test hard surface flooring and standardized test debris are used.1.1 This test method provides only a laboratory test for determining the relative hard surface floor-cleaning ability of household/commercial vacuum cleaners when tested under specified test conditions.1.2 This test method is applicable to household/commercial types of upright, canister, combination, and stick vacuum cleaners that use a dry primary dirt receptacle and are intended for cleaning hard surface floors as a primary or secondary function.1.3 This test method applies only to the removal of dry debris from hard surface floors, not the removal of embedded dirt from carpet.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring the Hard Surface Floor-Cleaning Ability of Household/Commercial Vacuum Cleaners

ASTM F888-06 测量真空吸尘器中主要灰尘收集器的最大功能容积的标准试验方法

This test method covers a procedure to determine the maximum functional volume of the primary dirt receptacle when installed in the vacuum cleaner. This test method provides the maximum amount of test media that the primary dirt receptacle will hold and may be more than the volume obtained when filled to the manufacturerrsquo;recommended fill line. 1.1 This test method covers household types of upright, canister, and combination vacuum cleaners.1.2 This test method provides a measurement in dry quarts or litres of the maximum functional volume of the primary dirt receptacle when installed in the vacuum cleaner.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see and .

Standard Test Method for Measuring Maximum Function Volume of the Primary Dirt Receptacle in a Vacuum Cleaner

ASTM F888-06(2011) 测量真空吸尘器的原灰尘收集器的最大功能容积的标准试验方法

This test method covers a procedure to determine the maximum functional volume of the primary dirt receptacle when installed in the vacuum cleaner. This test method provides the maximum amount of test media that the primary dirt receptacle will hold and may be more than the volume obtained when filled to the manufacturer's recommended fill line. 1.1 This test method covers household types of upright, canister, and combination vacuum cleaners. 1.2 This test method provides a measurement in dry quarts or litres of the maximum functional volume of the primary dirt receptacle when installed in the vacuum cleaner. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 7.2 and 8.5.

Standard Test Method for Measuring Maximum Function Volume of the Primary Dirt Receptacle in a Vacuum Cleaner

DLA A-A-50026 A VALID NOTICE 2-2006 洗衣房干燥和空调烘干机

A-A-50026A, dated 25 September 2001, has been reviewed and determined to be valid for use in acquisition.

DRYING AND CONDITIONING TUMBLERS, LAUNDRY

ASTM F1022-06 化学消毒商用洗碗碟机,循环洗涤以及清水漂洗等型号机器

1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled chemical sanitizing commercial dishwashing machines. Note 18212;Several standards that apply generally to the product described in this specification are listed in the Appendix X1.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only.1.3 The following precautionary caveat pertains only to the test method portion: Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chemical Sanitizing Commercial Dishwashing Machines, Recirculated Wash, Fresh Water Rinse Type

ASTM F820-06 测量中央真空吸尘系统的空气性能特征的测试方法

The test results allow the comparison of the maximum air power available when no dirt has been introduced into the vacuum cleaning system, that is, a completely clean filter or an empty, clean dirt container.1.1 This test method covers procedures for determining air performance characteristics of household central vacuum cleaning systems, which use a flexible cleaning hose assembly and incorporates a series universal motor(s). This test method does not apply to the carpet cleaning mode of operation where dirt or debris is involved.1.2 These tests and calculations include determination of suction, airflow, air power, maximum air power, and input power under standard operating conditions (see Note 0).Note 0For more information on air performance characteristics, see Refs ().1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in Note 0.

Test Method for Measuring Air Performance Characteristics of Central Vacuum Cleaning Systems

ANSI Z21.5.2a-2006 气体衣物干燥器用标准.卷II、 2型衣服烘干机

Details test and examination criteria for Type 2 clothes dryers for use with natural, manufactured or mixed gases, liquefied petroleum gases or LP gas-air mixtures.

Standard for Gas Clothes Dryers, Volume II, Type 2 Clothes Dryers,

ANSI Z21.5.1-2006 燃气衣物干燥器、卷I、 1型干衣机(与CSA 7.1b相同)

Details test and examination criteria for Type 1 clothes dryers for use with natural, manufactured or mixed gases, liquefied petroleum gases or LP gas-air mixtures.

Gas Clothes Dryers, Voluem I, Type 1 Clothes Dryers (same as CSA 7.1)

ASTM F2105-06 测量真空吸尘器发动机/风扇系统的空气性能特性的标准试验方法

The test results allow the comparison of the maximum air power at the vacuum cleaner motor/fan system inlet under the conditions of this test method.1.1 This test method covers procedures for determining air performance characteristics of series universal motor/fan systems used in commercial and household upright, canister, stick, hand-held utility, combination-type vacuum cleaners, and household central vacuum cleaning systems.1.2 These tests and calculations include determination of suction, airflow, air power, maximum air power, and input power under specified operating conditions.Note 1For more information on air performance characteristics, see References () through ().1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaner Motor/Fan Systems

JIS C 9335-2-67:2005 家用和类似用途电器.安全.第2-67部分:商业和工业用地板清洁机和处理机的特殊要求

この規格は，湿式及び/又は乾式吸引装置を組み込んだ機器を含む，主として産業及び業務用に設計された電気モータ駆動機器(附属装置があろ又はない。)であっで，定格電圧が単相にあっでは250V以下,その他の機器にあっては480V以下のものの安全性について規定する。

Household and similar electrical appliances -- Safety -- Part 2-67: Particular requirements for floor treatment and floor cleaning machines, for industrial and commercial use

KS C IEC 61855:2005 家用电动毛发护理用具的性能测量方法

이 규격은 모발을 건조하고, 모양을 만드는 가정용 및 이와 유사한 용도의 전기 기기(그

Household electrical hair care appliances－Methods of measuring the performance