Y81 家具制品 标准查询与下载

AS/NZS 2172:2003 家用轻便小床.安全要求

This Standard specifies safety requirements for cots. These include material, design, construction, performance, labelling and marking requirements, all of which are important for the well-being of children who use cots. The Standard is applicable to cots for use in household situations. It is not applicable to folding cots. Folding cots are covered in AS/NZS 2195, however folding timber cots are required by AS/NZS 2195 to meet some parts of this Standard.

Cots for household use—Safety requirements

QB/T 2600-2003 棕纤维弹性床垫

本标准规定了棕纤维弹性床垫的定义和代号、产品分类、要求、试验方法、检验规则、检验结果评定及标志、包装、运输、贮存。 本标准适用于家庭、宾馆、饭店、医院等场合使用的棕纤维弹性床垫，其它天然植物纤维床垫可参照本标准使用。

Resilient mattress with palm fibre and coir

QB/T 1952.1-2003 软体家具.沙发

本标准规定了沙发的定义、产品分类、要求、试验方法、检验规则及检验结果评定和标志、包装、运输及贮存。 本标准适用于会客、休息等室内用途的沙发。本标准不适用于木制的沙发椅。

Upholstered furniture sofa

QB/T 2603-2003 木制宾馆家具

本标准规定了木制宾馆家具的术语和定义、要求、试验方法、检验规则和产品标志、包装、运输、贮存。 本标准适用于宾馆、酒店、旅馆和饭店等客房内使用的木制家具。

Wooden furniture for hotel

QB/T 2602-2003 影剧院公共座椅

本标准规定了供影剧院、会议厅、多功能厅内使用的公共座椅的分类、定义、要求、试验方法、检验规则及标志、包装、运输和贮存ε 本标准适用于影剧院、会议厅、多功能厅室内使用以软面座椅为主的公共座椅，也适用于歌舞厅等室内使用的同类公共座椅。

Public seat for theatre

QB/T 2601-2003 体育场馆公共座椅

本标准规定了体育场馆使用的公共座椅的分类、定义、要求、试验方法、检验规则及标志、包装、运输、贮存等。 本标准适用于室内外体育场馆使用的以硬质座面为主的公共座椅，也适用于其它场合如快餐店、商店、机场、车站、医院、学校等场所使用的同类公共座椅。

Public seat for stadium and gymnasium

DIN EN 527-3:2003 办公家具.工作台和写字台.第3部分:测定结构稳定性和机械强度的试验方法

Office furniture - Work tables and desks - Part 3: Methods of test for the determination of the stability and the mechanical strength of the structure; German version EN 527-3:2003

BS EN 527-3:2003 办公家具.工作台和写字台.结构的稳定性和机械强度测定的试验方法

This part of EN 527 specifies methods of test for the determination of the stability and the mechanical strength of the structure of office work tables and desks. NOTE In this standard, the words 《table 》and 《desk 》have the same meaning. For simplicity, only the word 《table 》is used in the remainder of the standard. The tests are designed to be applied to an article of furniture that is fully assembled and ready for use.

Office furniture - Work tables and desks - Methods of test for the determination of the stability and the mechanical strength of the structure

BS EN 527-2:2003 办公家具.工作台和写字台.机械安全要求

Office furniture - Work tables and desks - Mechanical safety requirements

ASTM F1561-03 户外用塑料椅子标准性能要求

1.1 These requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chairs intended for outdoor use.1.2 These requirements do not address conditions that affect the performance of the chair beyond the manufacturing site.1.3 These requirements are not applicable to chaises, multipositional chairs, upholstered chairs, or other types of furniture.1.4 These requirements cover the physical performance of product regarding the aspects of outdoor weathering, impact, static load, and rear leg testing.1.5 Products may be manufactured from recycled plastics as long as the performance requirements are met.1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Requirements for Plastic Chairs for Outdoor Use

ASTM F1561-03(2008) 户外用塑料椅标准性能要求

Tests and criteria as outlined determine the overall usability and stability of chairs in an environment simulating the conditions of use. Tests simulate two types of surfaces: Smooth surfaces such as linoleum, wet pool decks, etc. The glass testing base (Fig. 2) is used to simulate this surface. Rough surfaces such as wooden decks, outdoor grassed areas, etc. The plywood testing base (Fig. 3) is used to simulate this surface. Note8212;A = poly(methyl methacrylate) sheet (see standard specifications); B = AC exterior glue fir plywood (see standard specifications); C = polypropylene microfoam sheet (see standard specifications); D = glass/tempered (see standard specifications). FIG. 2 Glass Testing Base Note8212;A = poly(methyl methacrylate) sheet (see standard specifications); B = AC exterior glue fir plywood (see standard specifications). FIG. 3 Plywood Testing Base1.1 These requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chairs intended for outdoor use. 1.2 These requirements do not address conditions that affect the performance of the chair beyond the manufacturing site. 1.3 These requirements are not applicable to chaises, multipositional chairs, upholstered chairs, or other types of furniture. 1.4 These requirements cover the physical performance of product regarding the aspects of outdoor weathering, impact, static load, and rear leg testing. 1.5 Products may be manufactured from recycled plastics as long as the performance requirements are met. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Requirements for Plastic Chairs for Outdoor Use

ASTM F1235-03(2008) 便携式拖椅消费者安全标准规范

1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair. 1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of chairs. 1.3 For the purposes of this specification a chair is: 1.3.1 A seat made for the express purpose of seating and holding a child who can remain in a sitting position due to his or her own coordination. 1.3.2 Usually a legless seat constructed to locate the occupant at a table in such a position and elevation so that the surface of the table can be used as the feeding surface for the occupant. 1.3.3 Supported solely by the table on which it is mounted. These chairs are intended for use by children between the ages of six months and three years and who weigh no more than 37 lb (16.8 kg) (95th percentile male at three years). 1.4 No chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains to the test methods portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Portable Hook-On Chairs

UL 962 BULLETINS-2003 家用和商用家具

Household and commercial furnishings

Household and commercial furnishings

ASTM F2236-03 软的婴儿运载工具的消费者安全标准规范

1.1 This consumer safety specification establishes performance requirements, test methods and marking requirements to promote safe use of soft infant carriers.1.2 This consumer safety specification is intended to minimize the risk of incidents to an infant from the normal use and reasonably foreseeable misuse of these products.1.3 For purposes of definition, a soft infant carrier is a product, normally of sewn fabric construction, which is designed to contain a full term infant, generally in an upright position, in close proximity to the caregiver. In general, the child will weigh between 7 and 25 lb (3.2 and 11.3 kg). The soft infant carrier is normally "worn" by the caregiver with the carrier, and thus the infant, suspended from one or both shoulders of the caregiver. These products are generally worn on the front of the caregiver's body with the infant either facing towards or away from the caregiver. This consumer safety specification does not include products generally referred to as "slings."1.4 No soft infant carrier produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein.1.5 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons or objects with the caregiver and infant while the soft carrier is in use.1.6 The test values stated in inch-pound units in this consumer safety specification are to be regarded as the standard. The metric values in parentheses are for reference only.1.7 The following precautionary caveat pertains only to the test method portion, Section of this consumer safety specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Consumer Safety Specification for Soft Infant Carriers

ASTM F1169-03 全尺寸婴儿带栏杆小床的标准规范

1.1 This consumer safety specification establishes performance requirements and test procedures to determine the structural integrity of cribs. It also contains design requirements addressing entanglement on crib corner post extensions, and requirements for warning labels and instructional material.1.2 No crib produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Full Size Baby Crib

SANS 12469:2002 生物技术．微生物安全柜的性能标准

Specifies basic requirements for microbiological safety cabinets (MSCs) with respect to safety and hygiene. It sets the minimum performance criteria for safety cabinets for work with microorganisms and specifies test procedures for microbiological safety

Biotechnology - Performance criteria for microbiological safety cabinets

DIN 16550-1:2002 办公家具.腰背挺直式工作位置写字台.第1部分:尺寸

This standard specifies dimensions for tables used for working in standing positions. It defines measures for table heights and their height adjustment with regard to safety-related and ergonomic criteria.

Office furniture - Tables for upright working position - Part 1: Dimensions

DIN EN 1335-1 Berichtigung 1:2002 办公家具 办公室工作椅 第1部分：尺寸 尺寸的测定

The document applies to office work chairs. It specifies dimensions of three types of chairs as well as test methods for their determination.

Office furniture - Office work chair - Part 1: Dimensions - Determination of dimensions

BS EN 13761:2002 办公家具.来访者用座椅

This European Standard specifies dimensions and safety requirements for visitors chairs. The dimensional requirements are not applicable to easy chairs.

Office furniture - Visitors chairs

KS G 4214-2002 家具.桌子.强度和耐久性测定

이 규격은 완전하게 조립되어 사용 가능한 상태에 있는 테이블의 강도와 내구성을 평가하기 위

Furniture－Table－Determination of strength and durability