ISO 48 E标准-分析测试百科网

DIN ISO 48 E:2015 文件草案硫化橡胶或热塑性橡胶硬度测定（硬度在 10 IRHD 和 100 IRHD 之间）（ISO 48:2010）

Draft Document - Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD) (ISO 48:2010); Text in German and English

DIN ISO 48 E:2015-11 硫化或热塑橡胶硬度的测定(硬度在10 IRHD至100 IRHD之间

Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD)

DIN ISO 48-9 E:2020 文件草案硫化或热塑性橡胶硬度测定第9部分：硬度测试仪的校准和验证（ISO 48-9:2018）文本为德语和英语

Draft Document - Rubber, vulcanized or thermoplastic - Determination of hardness - Part 9: Calibration and verification of hardness testers (ISO 48-9:2018); Text in German and English

DIN ISO 48-2 E:2020 文件草案硫化或热塑性橡胶硬度测定第2部分：10 IRHD 至 100 IRHD 之间的硬度（ISO 48-2:2018）文本为德语和英语

Draft Document - Rubber, vulcanized or thermoplastic - Determination of hardness - Part 2: Hardness between 10 IRHD and 100 IRHD (ISO 48-2:2018); Text in German and English

DIN ISO 48-4 E:2020 文件草案硫化橡胶或热塑性橡胶硬度测定第4部分：硬度计法压痕硬度（肖氏硬度）（ISO 48-4:2018）文本为德语和英语

Draft Document - Rubber, vulcanized or thermoplastic - Determination of hardness - Part 4: Indentation hardness by durometer method (Shore hardness) (ISO 48-4:2018); Text in German and English

DIN ISO 48-3 E:2020 文件草案硫化或热塑性橡胶硬度测定第3部分：使用极低橡胶硬度 (VLRH) 标度的静载硬度 (ISO 48-3:2018) 文本为德语和英语

Draft Document - Rubber, vulcanized or thermoplastic - Determination of hardness - Part 3: Dead-load hardness using the very low rubber hardness (VLRH) scale (ISO 48-3:2018); Text in German and English

DIN ISO 48-8 E:2020 文件草案硫化或热塑性橡胶硬度测定第8部分：采用 Pusey 和 Jones 方法测定橡胶包覆滚筒的表观硬度 (ISO 48-8:2018) 文本为德语和英语

Draft Document - Rubber, vulcanized or thermoplastic - Determination of hardness - Part 8: Apparent hardness of rubber-covered rollers by Pusey and Jones method (ISO 48-8:2018); Text in German and English

ISO/R 48:1957 ISO/R 48:1957

ISO/R 48:1968 ISO/R 48:1968

DIN ISO 48-3 E:2020-08 硫化橡胶或热塑性橡胶硬度的测定第3部分：使用极低橡胶硬度(VLRH)刻度的静载硬度

Rubber, vulcanized or thermoplastic - Determination of hardness - Part 3: Dead-load hardness using the very low rubber hardness (VLRH) scale

DIN ISO 48-4 E:2020-08 硫化或热塑性橡胶硬度测定第4部分：用硬度计法测定压痕硬度(肖氏硬度

Rubber, vulcanized or thermoplastic - Determination of hardness - Part 4: Indentation hardness by durometer method (Shore hardness)

DIN ISO 48-2 E:2020-08 硫化或热塑性橡胶硬度测定第2部分：10 IHD到100 IHD之间的硬度

Rubber, vulcanized or thermoplastic - Determination of hardness - Part 2: Hardness between 10 IRHD and 100 IRHD

DIN ISO 48-8 E:2020-08 硫化橡胶或热塑性橡胶硬度的测定第8部分：用Pusey和Jones方法测定橡胶包覆辊的表观硬度

Rubber, vulcanized or thermoplastic - Determination of hardness - Part 8: Apparent hardness of rubber-covered rollers by Pusey and Jones method

DIN ISO 48-9 E:2020-08 硫化橡胶或热塑性橡胶硬度的测定第9部分：硬度测试仪的校准和验证

Rubber, vulcanized or thermoplastic - Determination of hardness - Part 9: Calibration and verification of hardness testers

DIN ISO 48:2009 硫化或热塑橡胶.硬度的测定(硬度在10 IRHD至100 IRHD之间)(ISO 48:2007),DIN ISO 48:2009-10的英文版本

1.1 General This International Standard specifies four methods for the determination of the hardness of vulcanized or thermoplastic rubbers on flat

Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD) (ISO 48:2007);English version of DIN ISO 48:2009-10

ISO 48 E 标准查询与下载