H31 人造富矿 标准查询与下载

GB/T 24531-2009 高炉和直接还原用铁矿石 转鼓和耐磨指数的测定

本标准规定了铁矿石转鼓和耐磨指数由于冲击和磨损而使粒级降低程度的测定方法。 本标准适用于块矿、烧结矿和球团矿。

Iron ores for blast furnace and direct reduction feedstocks-Determination of the tumble and abrasion indices

GB/T 21236-2007 电炉回收二氧化硅微粉

本标准规定了二氧化硅微粉产品的牌号、技术要求、试验方法、检验规则、包装、标志、贮存、运输和质量证明书。 本标准适用于硅铁和工业硅等生产中，通过电炉的烟罩收集的含硅气体氧化凝聚后，经干法收尘装置收集的二氧化硅微粉，该产品在本标准中被称为“电炉回收二氧化硅微粉”，简称为“二氧化硅微粉”(俗称“硅灰”)。

Silica fume from electric-furnace

GB/T 20491-2006 用于水泥和混凝土中的钢渣粉

本标准规定了用于水泥和混凝土中的钢渣粉的术语和定义、技术要求、试验方法、检验规则、包装、标志、运输和贮存。 本标准适用于水泥和混凝土中钢渣粉的生产和检验。 本标准也适用于钢渣粉与粒化高炉矿渣粉、粉炭灰复合的产品。

Steel slag powder used for cement and concrete

EN 10293:2015 钢铸件.一般工程用钢铸件

This European Standard applies to steel castings: for general engineering uses. Its uses include machinery (mechanical, electrical...), automotive industries, railroad, armament, agricultural equipment, mining, etc. In cases where castings are joined by welding by the founder, this document applies. In cases where castings are welded; - to wrought products (plates, tubes, forgings...), or; - by non-founders, this document does not apply.

Steel castings - Steel castings for general engineering uses

JIS G 5505:2013 紧密石墨铸铁(蠕墨铸铁)

This Standard specifies CV graphite cast irons.

Compacted (vermicular) graphite cast irons

ASTM A957/A957M-13 一般工业用钢和铝熔模铸造通用要求的标准规格

1.1 This specification covers a group of requirements that are mandatory for castings produced by the investment casting process to meet the metallurgical requirements of the following steel casting specifications issued by ASTM. ASTM Designation Title of Specification A27/A27M Steel Castings, Carbon, for General Application A128/A128M Steel Castings, Austenitic Manganese A148/A148M Steel Castings, High-Strength, for Structural Purposes A297/A297M Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat-Resistant, for General Application A447/A447M Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service A494/A494M Castings, Nickel and Nickel Alloy A560/A560M Castings, Chromium-Nickel Alloy A732/A732M Castings, Investment, Carbon and Low Alloy Steel for General Application, and Cobalt Alloy for High Strength at Elevated Temperatures A743/A743M Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion-R......

Standard Specification for Investment Castings, Steel and Alloy, Common Requirements, for General Industrial Use

KS D ISO 5922:2008 可锻铸铁

이 규격은 가단 주철품의 요구사항에 관하여 규정한다. 또한 기계적 성질에 기초하여 분류하는

Malleable iron castings

KS E ISO 8263:2007 铁矿石粉.烧结试验结果的表示方法

이 규격은 소결 시험 결과의 표현 방법을 규정한다. 소결 공정으로 집괴되는 모든 철광석 분

Iron ore fines－Method for presentation of the results of sintering tests

YB/T 421-2005 铁烧结矿

本标准规定了铁烧结矿的分类和标记、技术要求、试验方法、检验规则、包装、标志和质量证明书。 本标准适用于供高炉冶炼用的铁烧结矿。

Iron and sintering ore

YB/T 005-2005 酸性铁球团矿

本标准规定了酸性铁球团矿的技术要求、试验方法、检验规则、包装、标志、运输、贮存和质量证明书。 本标准适用于供高炉冶炼用的酸性铁球团矿。

Acidic iron ore pellets

ISO 5922:2005 可锻铸铁

This International Standard specifies requirements for two types of malleable cast iron, namely whiteheart malleable cast iron and blackheart malleable cast iron, used in the manufacture of castings. Classification is given for each type of malleable cast iron on the basis of mechanical properties determined on separately cast test pieces. This International Standard is applicable only to malleable cast iron cast into sand moulds or moulds of comparable thermal diffusivity.

Malleable cast iron

JIS M 8718:2000 铁矿石颗粒.抗压强度的测定

この規格は,焼成した鉄鉱石べレットの圧かい(潰)強度試験方法について規定する。

Iron ore pellets -- Determination of crushing strength

YB/T 140-1998 水泥用钢渣化学分析方法

Method for chemical analysis of steel slag in cement

YB/T 148-1998 水泥用钢渣中金属铁含量测定方法

Standard test method for the content of metallic iron in steel slag used in cement

YB/T 106-1997 高钛冷固球团矿

Cold-bounded high-titaning bearing pellets

ASTM E279-97(2005) 铁矿丸和烧结矿抗磨性测定的试验方法

This test method is a comparative method intended primarily to test materials for compliance with compositional specifications or for monitoring. It is assumed that all who use these procedures will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Appropriate quality control practices must be followed such as those described in Guide E 882. This test method is used to monitor the feed to blast furnaces for process control.1.1 This test method covers a relative measure of the resistance of iron ore pellets and sinter to degradation by impact and by abrasion.1.2 The values as stated in SI units are to be regarded as the standard. The values in parentheses are given for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Abrasion Resistance of Iron Ore Pellets and Sinter by the Tumbler Test

YB 4099-1996 钢渣砌筑水泥

Steel slag masonry cement

YB 4098-1996 钢渣道路水泥

Steel slag cement for road

ASTM A834-95(2006) 一般工业用的普通要求的铸铁的标准规范

1.1 This specification covers a group of requirements that are mandatory requirements when used in conjunction with the following iron casting specifications issued by ASTM:ASTM Specification2A 47/A 47MA 48/A 48MA 197/A 197MA 220/A 220MA 278A 319A 395/A 395MA 436A 439A 518/A 518MA 532/A 532MA 536A 571/A 571MA 823A 842A 874/A 874MA 897/A 897M 1.2 This specification also covers a group of supplementary requirements which may be applied to the above specifications as indicated herein. These are provided for use when additional testing or inspection is desired and apply only when specified individually by the purchaser in the order. 1.3 The requirements of the individual material specification, and this general specification shall prevail in the sequence named. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Common Requirements for Iron Castings for General Industrial Use

YB/T 057-1994 低热钢渣矿渣水泥

Low heat steel slag cement