共找到 39 条与 长度和角度测量 相关的标准,共 3 页
Dimension measurement of hot free forgings and rolled rings
本标准规定了直流差动变压器式位移传感器的术语和定义、产品分类、基本参数、要求、试验方法、检验规则、标志、使用说明书、包装和贮存。本标准适用于由振荡器、差动变压器和解调器组成一体的直流差动变压器式位移传感器(以下简称传感器)。
Direct-current linear variable differential transformer (DC-DC LVDT) displacement transducers
本标准规定了普通螺纹量规的术语和定义、分类、符号、牙型、公差、要求、检验、标志与包装等。 本标准适用于牙型角为60°,公称直径为1mm至355mm,螺距为0.2mm至8mm的普通螺纹量规。 本标准规定的普通螺纹量规(以下简称“螺纹量规”)适用于检验GB/T 192-2003、GB/T 193-2003、GB/T 196-2003、GB/T 197-2003规定的普通螺纹。
Specification of gauges for general purpose screw threads
本标准规定了普通螺纹量规的型式与尺寸。 本标准适用于牙型角为60°,公称直径为1mm至180mm,螺距为0.2mm至6mm的普通螺纹量规所用的测头与手柄。 本标准规定的普通螺纹量规(以下简称“螺纹量规”)的型式与尺寸适用于GB/T 3934-2003规定的普通螺纹量规(不包括螺距为8mm的)。
Types and dimensions of gauges for general purpose screw threads
温度变化试验的目的在于确定温度变化或连续温度变化对试验样品的影响。
Environmental testing for electric and electronic products--Part 2: Test methods Guidance on change of temperature tests
本标准规定了矩形花键量规(以下简称“量规”)的各项尺寸公差、技术要求和标志与包装。 本标准适用于检验GB1144《矩形花键公差和检验》用的量规。
Gauges for straight-sided splines
本标准规定了水准泡的产品分类、技术要求和试验方法。 本标准适用于安平和测量微小倾角的圆形和管状水准泡。
Level
本标准规定了有关圆度测量的术语、定义及参数。
Measurement of roundness--Terms,definitions and parameters of roundness
本标准规定了用接触式(触头式)仪器测量半径变化来确定圆度误差的方法及仪器的一般特性。 本标准适用于在给定条件下,经轮廓变换,以下列任一圆心来评定零件轮廓对理想圆的偏离。 最小区域圆圆心; 最小二乘方圆圆心; 最小外接圆圆心; 最大内接圆圆心。
Methods for the assessment of departure from roundness--Measurement of variations in radius
本标准规定了用两点、三点法测量来确定圆度误差值的一种方法,适用于测量零件内、外圆形要素的圆度误差。 两点、三点测量得到的数值与实际的圆度误差值存在着差异,必须由本标准给出的反映系数进行修正。 与本标准有关的标准 GB 1183-80《形状和位置公差 术语及定义》 GB 1958-80《形状和位置公差 检测规定》
Assessment of departure from roundness--Two and three point methods
This International Document relates to automatic pipettes which are generally used as national primary standards of volume. It gives advice on the manufacture and installation of such standards together with their calibration, use and maintenance. Automatic pipettes are used by national laboratories, services of legal metrology and regional laboratory metrological offices for the calibration of volumetric standards of a lower order and for the verification of volumetric instruments - including volumetric glassware (flasks etc.), a field which is covered by various OIML International Recommendations and ISO Standards (see clause 13 for references to International Standards and Recommendations relating to laboratory glassware).
Glass delivery measures - Automatic pipettes
Technical Requirements for Laser Arch Meter
Laser shaft alignment instrument technical requirements
本标准规定了普通高度标尺的产品分类、要求、试验方法、检验规则,及标志、包装、运输与贮存。 本标准适用于一般工程测量和土木建筑、装潢、机械安装等作业测量的普通高度标尺。以下简称“标尺”。
Altitude scales
本标准规定了轮式测距仪的术语和定义、产品分类、要求、试验方法、检验规则,及标志、产品说明书、包装、运输与贮存。 本标准适用于测量室内外地面距离的轮式测距仪。
Measuring wheels
本标准适用于地表水、地下水、生活污水和工业废水中甲醇的测定
Determination of Methanol in Water by Static Headspace/Direct Injection Gas Chromatography
本标准适用于公路工程路面面层施工、工程验收及旧路调查等厚度检测
Method of Pavement Radar Detecting Pavement Surface Thickness
本标准规定了汽车外廓尺寸测量仪的(以下简称测量仪)的术语和定义、分类、型号、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于汽车安全技术、综合性能检验等在检测线上使用的测量仪。
General technical requirements for measuring instruments for automobile external dimensions
Verticality measuring ruler calibration device
Inclined block micrometer calibrator
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号