17.200 热力学和温度测量 标准查询与下载

GB/T 4994-2015 铁-铜镍(康铜)热电偶丝

本标准规定了铁一铜镍〔康铜)热电偶丝的产品分类、技术要求、试验方法、检验规则、供应方式、包装及标志。 本标准适用于制造工业铁一铜镍〈康锏)热电偶U型热电偶〉用合金丝〈以下简称偶丝)。

Iron/Copper-Nickel (Constantan) thermocouple wires

GB/T 29822-2013 钨铼热电偶丝及分度表

本标准规定了钨铼热电偶丝(以下简称为偶丝)的产品分类、技术要求、试验方法、检验规则、供应方式、包装和标识。本标准适用于制造钨铼3—钨铼25热电偶丝、钨铼5—钨铼26热电偶丝、钨铼5—钨铼20热电偶丝(以下分别简称为D型偶丝、C型偶丝和A型偶丝)。

Tungsten-rhenium thermocouple wires and temperature-electromotive force (EMF) tables

GB/T 4990-2010 热电偶用补偿导线合金丝

本标准规定了电热偶用补偿导线合金丝的产品分类、技术要求、试验方法、检验规则、标志、包装等。 本标准适用于分度号为S、R、K、N、E、J和T的热电偶配用的补偿导线合金丝。

Alloy wires of extension and compensating cables for thermocouples

GB/T 4834-2001 直读/非直读式电容型袖珍剂量计

本标准规定了直读/非直读式电容型袖珍剂量计的技术要求、试验方法和检验规则等。 本标准适用于测量能量为20keV～3MeV的X、γ辐射累积剂量的电容型袖珍剂量计。真空室型剂量计可参照使用。

Direct or indirect-reading capacitor-type pocket dosemeters

DB1304/T 390-2022 矿用温度传感器检测方法

Detection method of mining temperature sensor

GSO IEC TS 63144-1:2022 工业过程控制设备 热成像相机 第1部分：计量表征

IEC 63144-1:2020(E) applies, in the field of metrology, to the statement and testing of technical data in datasheets and instruction manuals for thermographic cameras that are used to measure the temperature of surfaces. This includes, unless otherwise stated, both two-dimensional and one-dimensional (line cameras or line scanners) temperature measuring instruments, independently of the scanning principle (fixed multi-element detector or scanning camera system). This document describes standard test methods to determine relevant metrological data of thermographic cameras. Manufacturers and sellers can choose relevant data and can state that the data shall be compliant with this Technical Specification.

Industrial process control devices - Thermographic cameras - Part 1: Metrological characterization

DB13/T 3016-2018 地温食品储运温控技术要求

Technical requirements for temperature control of ground temperature food storage and transportation

DB12/T 3012-2018 冷链物流 温湿度要求与测量方法

本标准适用于低温食品农产品（以下称为物品） 的物流保鲜作业。

Cold chain logistics temperature and humidity requirements and measurement methods

DB13/T 3012-2018 冷链物流 温湿度要求与测量方法

Cold chain logistics temperature and humidity requirements and measurement methods

DB11/T 3012-2018 冷链物流 温湿度要求与测量方法

Cold chain logistics temperature and humidity requirements and measurement methods

DB11/T 3016-2018 低温食品储运温控技术要求

Technical requirements for temperature control of low-temperature food storage and transportation

DB14/T 1538-2017 农产品冷链物流 果蔬贮运指南

本标准适用于果蔬类农产品冷链物流贮存和运输。

Guidelines for Storage and Transportation of Fruits and Vegetables in Cold Chain Logistics of Agricultural Products

DB11/T 1388-2017 通断时间面积法供热计量系统技术规范

Technical specification for heating metering system by on-off time area method

DB12/T 560-2015 冷链物流 温度检测与要求规范

本标准适用于主要低温食品的物流保鲜作业

Cold chain logistics temperature detection and requirements specification

SB/T 11092-2014 多温冷藏运输装备技术要求及测试方法

本标准规定了多温冷藏运输装备的分类和标记、技术要求、测试方法和检验规则等。本标准适用于多温冷藏汽车、多温冷藏集装箱等各类多温冷藏运输装备。其他型式的多温多空间冷藏运输装备可参照本标准执行。

The technical requirements and test methods of multi temperature refrigerated transport unit

CAN/CSA-C900.1-2013(R2018) 热量表 第1部分：一般要求（采用 EN 1434-1:2007 第二版 2007-02 有加拿大偏差）

Scope This European Standard specifies the general requirements and applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed (cooling) or given up (heating) by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units. Electrical safety requirements are not covered by this European Standard. Pressure safety requirements are not covered by this European Standard. Surface mounted temperature sensors are not covered by this European Standard.

Heat meters - Part 1: General requirements (Adopted EN 1434-1:2007, second edition, 2007-02, with Canadian deviations)

CAN/CSA-C900.4-2013(R2018) 热量表 第4部分：型式认可测试（采用 EN 1434-4:2007 第二版 2007-02 有加拿大偏差）

1 Scope This European Standard applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed or given up by a liquid called the heat-conveying liquid. The meter indicates heat quantity in legal units. Electrical safety requirements are not covered by this standard.

Heat meters - Part 4: Pattern approval tests (Adopted EN 1434-4:2007, second edition, 2007-02, with Canadian deviations)

CAN/CSA-C900.2-2013(R2018) 热量表 第2部分：结构要求（采用 EN 1434-2:2007 第二版 2007-02 加拿大有偏差）

Scope This European Standard specifies the constructional requirements and applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed (cooling) or given up (heating) by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units. Electrical safety requirements are not covered by this European Standard. Pressure safety requirements are not covered by this European Standard. Surface mounted temperature sensors are not covered by this European Standard.

Heat meters - Part 2: Constructional requirements (Adopted EN 1434-2:2007, second edition, 2007-02, with Canadian deviations)

CAN/CSA-C900.3-2013(R2018) 热量表 第3部分：数据交换和接口（采用 EN 1434-3:2008 第二版 2008-10）

Scope This European Standard applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed or given up by a liquid called the energy-conveying liquid. The meter indicates heat in legal units. Electrical safety requirements are not covered by this standard. Part 3 specifies the data exchange between a meter and a readout device (POINT / POINT communication). For these applications using the optical readout head, the EN 62056-21 protocol is recommended. For direct or remote local readout of a single or a few meters via a battery driven readout device, the physical layer of EN 13757-6 (local bus) is recommended. For bigger networks with up to 250 meters, a master unit with AC mains supply according to EN 13757-2 is necessary to control the M-Bus. For these applications the physical and link layer of EN 13757-2 and the application layer of EN 13757-3 is required. For wireless meter communications, EN 13757-4 describes several alternatives of walk/drive-by readout via a mobile station or by using stationary receivers or a network. Both unidirectionally and bidirectionally transmitting meters are supported by this standard.

Heat meters - Part 3: Data exchange and interfaces (Adopted EN 1434-3:2008, second edition, 2008-10)

DB37/T 2399-2013 室内空气温度测量方法

本标准适用于规定的供暖期内，用温度测量器具在集中供暖室内进行的空气温度测量（包括第三方测量机构进行的室温测量和日常室温监测）。

Indoor air temperature measurement method