共找到 37 条与 流体存储装置 相关的标准,共 3 页
本标准规定了石墨制压力容器的通用要求、材料、设计、制造、检验和验收及容器出厂要求。本标准适用于具备以下条件的石墨制压力容器: ———工作压力大于或等于0.1 MPa,设计压力不大于2.4 MPa; ———设计温度-70 ℃~205 ℃ ; ———盛装介质为气体、液化气体或介质最高工作温度高于或等于其标准沸点的液体。本标准不适用于下列石墨容器: ———直接火焰加热的石墨容器; ———核能装置中的石墨容器; ———浇铸石墨容器; ———主要应力由金属外壳承受的石墨砖板衬里设备。
Graphite pressure vessels
本标准规定了奥氏体不锈钢制自增压式液氮容器(以下简称自增压容器)的产品分类、技术要求、试验方法、检验规则、标志、包装及储运等要求。 本标准适用于储运介质为液氮,工作压力小于0.1MPa,有效容积为50L~800L,且采用高真空多层绝热的自增压容器的设计、制造。 本标准不适用于下列范围的自增压容器: ——带压贮存液氮; ——贮存液氧等其他低温液体。
Autoboosting caliber liquid nitrogen container
GB/T18443的本部分规定了真空绝热深冷设备漏率测量的试验原理与方法、试验装置、设备和仪器、l式验条件与试验准备、试验步骤、数据处理、试验记录与试验报告等要求.本部分适用于除储运液氢介质以外的真空绝热深冷压力容器、真空绝热深冷焊接气瓶、真空绝热管及莫管件等真空绝热深冷设备漏率的测量,其他设备可参照执行.
Testing method of performance for vacuum insulation cryogenic equipment.Part 3:Leak rate measurement
GB/T 18443的本部分规定了真空绝热深冷设备漏热量测量的试验原理与方法、试验装置、设备和仪器、试验条件与试验准备、试验步骤、数据处理和试验记录与试验报告等要求。 本部分适用于除储运液氢介质以外的真空绝热深冷压力容器、真空绝热深冷焊接气瓶、真空绝热管及其管件等真空绝热深冷设备的漏热量测量,表面温度测量法适用于真空绝热管及其管件的漏热量测量。
Testing method of performance for vacuum insulation cryogenic equipment.Part 6:Heat-leak rate measurement
GB/T18443 的本部分规定了真空绝热深冷设备维持时间测量的试验原理与方法、试验装置.设备和仪器,试验条件与试验准备.试验步又、数据处理和试验记录与试验报告等要求。 本部分适用于除储运液氢介质以外的真空绝热深冷压力容器真空绝热深冷焊接气瓶等真空绝热深冷设备维持时间的测量。
Testing method of performance for vacuum insulation cryogenic equipment.Part 7:Holding time measurement
GB/T 18443的本部分规定了真空绝热深冷设备容积测量的试验原理与方法、试验装置、设备和仪器、试验条件与试验准备、试验步骤、数据处理和试验记录与试验报告等要求。 本部分适用于除储运液氢介质以外的真空绝热深冷压力容器、真空绝热深冷焊接气瓶、真空绝热管及其管件等真空绝热深冷设备容积的测量。
Testing method of performance for vacuum insulation cryogenic equipment.Part 8:Volume measurement
GB/T 18443的本部分规定了真空绝热深冷设备性能试验对试验环境、试验设备、被检件与试验介质、试验项目和顺序、数据处理、试验记录和试验报告等的基本要求。 本部分适用于除储运液氢介质以外的真空绝热深冷设备性能试验,其他设备可参照执行。
Testing method of performance for vacuum insulation cryogenic equipment.Part 1:Basic requirements
GB/T 18443的本部分规定了真空绝热深冷设备夹层真空度测量的试验原理与方法、试验装置、设备和仪器、试验条件与试验准备、试验步骤、数据处理和试验记录与试验报告等要求。 本部分适用于除储运液氢介质以外的真空绝热深冷压力容器、真空绝热深冷焊接气瓶、真空绝热管及其管件等真空绝热深冷设备夹层真空度的测量,其他设备可参照执行。
Testing method of performance for vacuum insulation cryogenic equipment.Part 2:Vacuum degree measurement
GB/T 18443的本部分规定了真空绝热深冷设备静态蒸发率测量的试验原理与方法、试验装置、设备和仪器、试验条件与试验准备、试验步骤、数据处理和试验记录与试验报告等要求。 本部分适用于除储运液氢介质以外的真空绝热深冷压力容器、真空绝热深冷气瓶等真空绝热深冷设备静态蒸发率的测量,其他可参照执行。
Testing method of performance for vacuum insulation cryogenic equipment.Part 5:Static evaporation rate measurement
本标准规定了自增压式液氮容器的产品分类、技术要求、试验方法、检验规则、标志、包装、贮运。 本标准适用于畜牧、医疗、科研、工业等部门贮存和运输液氮的中型不锈钢制自增压式液氮容器。
Autoboosting calibre liquid nitrogen container
本标准规定了低温容器漏气速率(简称漏率)的检验原理、装置、试样、条件、准备、程序、结果的说明和检验报告。 本标准适用于采用真空绝热型的低温容器、低温介质输送管路及低温阀门的漏率检验。也适用于一般真空容器及其他容器的漏率检验。
Test methods for leak rate of cryogenic containers
Method for preparation and internal pressure testing of filamentwound pressure vessels
Performance Requirements for Pressurized Water Storage Tanks
Management Regulations for Safe Use of Pressure Vessels
Inspection methods for vacuum insulated cryogenic liquid tank containers
Integrated device for installation of heat pump systems for household and similar purposes
Heating enamel hot water storage tank
本标准规定了钢制立式储罐用采样器选用、检验及验收的技术要求。 本标准适用于石油化工、煤化工或石油库新建、改建、扩建工程中钢制立式储罐用采样器的选用、检验及验收。不适用于低温常压储罐用采样器的选用、检验及验收。
Standard for selection, inspection and acceptance of the sampler for vertical steel oil tanks in petrochemical industry
Safety self-locking quick opening blind plate
This recommended practice (RP) provides guidance on the selection of common types of valves used by the petroleum refining , chemical petrochemical an associated industries These include gate, ball, Plug, butterfly, check and globe valves covered by API and ASME Standards . Modulation control valves and Pressure relief valves outsides the scope of this RP. Installation issues are discussed briefly for a few valve types .
Valve Selection Guide
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号